|
|
|
|
|
|
Heavy-Duty Dust Collection
The continuous duty bag dust collector for those applications where cartridges will not work. The Bagtron comes in a full range of sizes, from 67 sq. ft. to 1750 sq. ft. of filter, thus giving CFM's of air moved from as low as 500 CFM and as high as 25,000 CFM. In addition custom / larger sizes are available.
Self Cleaning While Running
Online cleaning is accomplished by a solid state control board which sequentially energenizes solenoids, allowing diaphragm valves to dump compressed air from the storage header into the blow-down pipe. The blow-down pipes have orifices over the inlets of each bag. The primary air is then joined by secondary air in the clean chamber both to flex the bag, cracking the dust cake, and also to blow off the loosened dust. The large agglomerated dust particles will then fall to the hopper for discarge from the collector. The compressed air jet is processed through a Venturi before passing to the fabric of the bag.
Specifications
- 14 Gauge with ribs
- Magnehelic gauge
- 16 oz. singed polyester felt
- Internal Venturi
- Galvanized bag cages
- Nitro blue enamel
- 4.75" Dia bags - 6, 8, or 10 ft. long
Options
- Direct mounted blower/motor
- Volume control damper
- Fan silencer
- Bin vent design
- Rotary air lock
- Platform & ladder packs
- Explosion vents
- Photohelic gauge
|
|
Flowtron AC Series
Self-Cleaning Cartridge Air Cleaners
Quiet, Efficient Operation
The Flowtron Air Cleaner is packed with design features that go straight to the bottom line. The film-laminated media is state-of-the-art for collecting fine dust in heavy concentrations from a wide range of welding, grinding, and finishing operations. The large capacity dust filters clean thoroughly off-line for the lowest cost per pound of collected dust, and the low-speed backward inclined blower reduces the energy cost of moving the air.
SRR Self-Cleaning System
As compressed air reaches near-sonic velocity exiting from our Sonic Resonating Rapperª, its whipping motion raps the inside of the cartridge, dislodging even the material deeply packed into the pleats.
|
|
|
|
|
|
Multi-Purpose Dust Collection for Industry
The Filter 1 Pulsatron PFV Series of Dust Collectors utilize high efficiency cartridge filters to provide effective collection of a broad range of dust particles and contaminates, such as wood, composites, plastic, dry powder, metals, toner, and cement. Operations include grinding, sanding, foundry, welding, fabrication, blasting, metallizing, and powder coating. The Pulsatron is designed for customization to unique applications. It is available in configurations of variable dimensions, number of cartridges, and optional features to effectively clean particulates ranging in type, size, and loading amount.
The vertical orientation of the cartridge in the Pulsatron PFV allows the dust to be blown off and fall directly into the hopper. Power-pulse reverse-jet cleaning, backflushing the filters with short bursts of compressed air, operates on a solid state controller to provide automatic cleaning. The unit is available with optional backward inclined direct drive blowers for quiet, efficient operation.
Features
- High efficiency cartridge filters vertically oriented for effective dust removal
- Automatic power-pulse reverse-jet cleaning for continuous duty, uninterrupted filtration
- 3 phase TEFC motor on rubber vibration mounts
- Welded heavy-gauge steel construction with industrial epoxy gulf blue coating
Options
- Various Filter Medias to Fit the Application: 80/20 Blends, Spun Bond Polyester, Phenolic or PTFE Coated, Fire Resistant, High Temperature, Metal Impregnated
- Magnetic Motor Starters
- Hopper Slide Gate
- HEPA or CARBON Safety Afterfilters with Visible/Audible Alarms
- Backward Inclined Direct Drive Blower
|
|
|
|
|
|
The High Efficiency Cyclone Separator / Dust Collector
The Filter 1 Cyclotron combines a long tapered cone, a high velocity inlet, and a large internal helix to easily separate from the air stream all moderate size particles, such as saw dust chips and particles from metal grinding.The Cyclotron fans are positioned on the clean air side of the cyclone and are direct drive for low maintenence. In addition, the fans have backward inclined blower wheels for high efficiency and low noise operation. Optional Safety After Filters ensure that even the smallest particles are captured. Standard filter material for the after-filters is 16-ounce seared, felted polyester, designed to hold large dust particles to the outer edges, thus forming a filter cake which heightens filtering efficiency and facilitates easy removal.
Features
- Long, Tapered Cone
- High Velocity Inlet
- Large Internal Helix
- Heavy-Gauge Steel Construction with Industrial Blue Enamel Coating
- Direct Drive Backward Inclined Blower
Options
- Safety After Filters: Bags Fitted for 55-Gallon Drums
- Removable Galvenized Panels for Weather Exposure
- Drop Out Bins Built to Your Specifications
- Rotary Valves
- Spark Resistant Construction
- Radial Blower Wheels
- Sprinkler Heads
- Explosion Vents (Silencers)
|
|
Auto M shaker filter
The Auto M Z-Series is the latest generation of robust simple mechanically cleaned dust collectors suitable for non-continuous duty for industrial, commercial and educational locations.
Key features
• Neat, compact, unobtrusive, easy to clean exterior
• Robust weatherproof welded steel construction
• Electric shake cleaning, perfected by 30 years' experience
• No need for compressed air
• ATEX certified Baseefa 03 ATEX0225 for explosive dusts
• Simple maintenance, access from clean air side
• Many options including secondary filters to increase versatility.
Typical applications
• Metalwork, grinding, fettling, sanding, polishing
• Woodwork, dust extraction from small and medium workshops
• Bulk powders, chemicals, sack tipping, weighing, bagging
• Educational workshops – ceramics, metal work, crafts, woodwork,
|
|
U.S. Air Filtration baghouses (also called pulse jet baghouse, pulsejet dust collectors, etc...) are self contained, fully automated where needed. We also supply and install ducting, access platforms, ventilation and instrumentation. Baghouses are engineered for dusts of 3 microns and larger, in the following applications:
- Woodworking
- Powder processing
- Material handling
- Primary metals, including steel-making
- Metals fabrication: grinding, sawing, sanding, polishing
- Papermaking
- Ceramics manufacturing
- Mixing and blending options
- Mining
- Foundries
- Glass Plants
- Battery Plants
- Universities
|
|
FMK25 cassette filter
The FMK25 range of reverse jet cassette filters was developed for continuous operation in industrial process filtration and dust collection applications – incorporating the long established easily maintained Dantherm pocket fabric filter cassette.
Key features
• Tough galvanised steel construction
• Weatherproof for exposed locations
• Integral pre-separation chamber
• All maintenance from unit front
• Independently tested (FMKZ) with ATEX compliant features for explosive dusts
• Efficient cross flow / down flow inlet air pattern
• Wide range of integral or remote fans
Typical dust control and process applications
• Bulk materials handling – conveying, screening, sieving, mixing, bin/silo venting
• Building materials manufacture and distribution
• Chemical, plastics and pharmaceutical powders
• Processes with light or medium dust loading
|
|
|
|
|
|
Pulse Jet Cartridge Collectors
U.S. Air Filtration cartridge collectors offer significant advantages for many different applications. Each pulse jet dust collector is custom-engineered to a specific pressure or vacuum. Our cartridge collectors feature high efficiencies that are particularly important for applications involving toxic dusts or where air is being re-circulated. A cartridge collector is quite compact relative to the amount of airflow passing through them because of the large amount of media contained in each cartridge.
Cartridge collectors present minimal safety risks to workers changing the elements because they do not have to enter the collector to remove the filters. They remain in an outside "fresh air" environment, where their lungs, skin, and clothing have very little contact with dust inside the collector. Pulsejet bags cartridges can be replaced quickly, and workers are not exposed to the dusts. U.S. Air Filtration collectors and cartridges are engineered to work together as an integrated system. With 14 collector lines and 12 proprietary filter cartridges, U.S. Air Filtration can design a dust collection solution for your exact needs.
|
|
MCA Multi- Cyclone
The MCA is a range of seven multi-cylone separators designed particularly for high temperature applications. Gas flows up to 63,000 m3/h are possible with up to 60 modules.
Key features
* Robust fully welded steel construction
* Collection efficiency up to 97%
* 7 sizes with capacities from 2,800 to 63,000 m3/h
* Temperature tolerance up to 300 deg.C
* Optional thermal insulation
* Wide range of accessories
|
|
TP type bag filters
The TRIPULS bag filter is a space-saving filter that still provides optimum performance.The complete filter element (filter medium plus frame), specially designed for the TRIPULS filter, allows optimum deformation of the filtering medium during the cleaning of the filter, comparable that undergone by a TP.
Each filter element includes three injection tubes. Their design and the resulting features (high flow and a big difference in cleaning pressure), combined with the special TRIPULS filter element, guarantee maximum filtration for low compressed air consumption.
These qualities, added to the compact construction, with the possibility of the horizontal or vertical assembly of the filtering elements, make the TRIPULS an ideal solution for many dust extraction problems, when the space available is restricted.
|
|
Cyclones use the effects of centrifugal force and gravity to separate particles in suspension in gas. The geometry of cyclones is a determining factor in obtaining high efficiency. Various physical properties such as: temperature, composition and viscosity of the gas, shape, granulometry, relative density of the particles, concentration of dust need to be taken into account when defining their efficiency.
To deal with special problems, we offer special constructions: apparatus for high pressure or high negative pressure, with protection against abrasion, with heating of the body
|
|
Magnetically coupled centrifugal pumps of building group 2 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Housing, impeller, impeller magnet coating and rear casing can be made of either glass-fibre reinforced PP plastic or PVDF. Sleeve bearings, starting ring and centering shaft are made of 99.7% pure oxide ceramic. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
- With non-ventilated motor so that it is insensitive to vapour.
|
|
Magnetically coupled centrifugal pumps of building group 4.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Housing, impeller, impeller magnet coating and rear casing can be made of either glass-fibre reinforced PP plastic or PVDF. Sleeve bearings, starting rings and centering shaft are made of 99.7% pure oxide ceramic. The impeller starting ring is made of PTFE graphite. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
Magnetically coupled centrifugal pumps of building group 1 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Constructional design
Housing, impeller, impeller magnet coating and rear casing are made of either glass-fibre reinforced PP plastic or PVDF or stainless steel. Sleeve bearings, starting ring and centering shaft are made of 99.7% pure oxide ceramic. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
Vertical centrifugal immersion pumps
Seal lots and safe to run dry Solid plastic vertical centrifugal immersion pumps are used predominantly space-saving by direct installation into industrial environments. For strongly crystallizing media, centrifugal immersion Pumps are supplied with a special seal to avoid the penetration of steam and the connected crystallization. Standard depths of immersion are ranging from 200 mm up to 500 mm. Depths of immersion up to 1000 mm are possible by the means of an intermediate bearing
Fluids delivered:
- Acids, bases and mixtures
- Solvents
- Alkaline degreasing baths
- Electroplating baths
- Foto chemicals
- Radioactive, aseptic and precious liquids
- Food stuffs
- Other low-viscosity fluids
Fields of application:
- Electroplating
- Etching and cleaning plants
- Refrigerating machines
- Solar systems
- Sewage and water treatment
- Foto industry
- Textile and food industries, etc.
|
|
|
|
|
|
The centrifugal immersion pumps of building group 4 are used for wet-pit operation in containers, pits and tanks. Centrifugal immersion pumps for dry-well installation, i.e. to be installed and operated outside the container, are also available.
All components of pumps in plastic design that are in contact with the fluid are made of PP or PVDF. The pump shaft consists of a motor shaft made of stainless steel and a shaft-protecting tube of either PP or PVDF. Built-in elastomers are made of FPM (or also EPDM without surcharge). Centrifugal immersion pumps are equipped with overhang shafts so that there is no need to provide for shaft bearings in components that are in contact with the fluid. Thus, the pumps are safe to run dry and do not require regular service and maintenance.
There is no need of a mechanical sealing of the shaft. Only a so-called gas seal is installed beneath the motor to prevent aggressive vapours from penetrating the motor chamber. But this seal is never in contact with the fluid delivered.
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
Magnetically coupled centrifugal pumps of building group 2 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Housing, impeller, impeller magnet coating and rear casing can be made of either glass-fibre reinforced PP plastic or PVDF. Sleeve bearings, starting ring and centering shaft are made of 99.7% pure oxide ceramic. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
- With non-ventilated motor so that it is insensitive to vapour.
|
|
Magnetically coupled centrifugal pumps of building group 4.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Housing, impeller, impeller magnet coating and rear casing can be made of either glass-fibre reinforced PP plastic or PVDF. Sleeve bearings, starting rings and centering shaft are made of 99.7% pure oxide ceramic. The impeller starting ring is made of PTFE graphite. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
Magnetically coupled centrifugal pumps of building group 1 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Constructional design
Housing, impeller, impeller magnet coating and rear casing are made of either glass-fibre reinforced PP plastic or PVDF or stainless steel. Sleeve bearings, starting ring and centering shaft are made of 99.7% pure oxide ceramic. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
|
|
|
|
Standard Filter Corporation now offers the finest Diaphragm Valves manufactured by Goyen! The valves are available in a wide range of configurations to suit a variety of reverse pulse filter designs. These sophisticated valves precisely control airflow through the filters for optimal cleaning. The range now includes the exciting 'next generation' Millennium series which sets a new standard in performance, design, ease of installation and maintenance economy. The range of Diaphragm valves includes:
3 Series Pulse Jet Valves
Superior performance, easy maintenance diaphragm valve available with threaded ports (T3 Series), dresser nut ports (DD3 Series) or flange and slide ports (FS3 Series). Outlet at 90 degrees to inlet.
T Series Pulse Jet Valves
High performance diaphragm valve with threaded ports. Available with integral pilot or as remotely piloted valve. Outlet at 90 degrees to inlet.
DD Series Pulse Jet Valves
High performance diaphragm valve with dresser nut ports. Available with integral pilot or as remotely piloted valve. Outlet at 90 degrees to inlet.
FS Series Pulse Jet Valves
Very high performance diaphragm valve with flanged inlet port and slide seal outlet port for easy valve installation and removal. Available with integral pilot or as remotely piloted valve. Outlet at 90 degrees to inlet.
|
|
|
U.S. Air Filtration can provide dust collector diaphragm valves in a range of configurations to suit all types of pulse jet cleaning baghouse designs. These sophisticated diaphragm valves utilize a flexible molded diaphragm to regulate airflow through the filters for optimal cleaning. The diaphragm valve creates a pulse of air that shakes through the bag, shaking off any dirt from the outside of the bag, cleaning the filter. U.S. Air Filtration can provide a replacement diaphragm valve for any dust collection application. Specifically, we stock and distribute Goyen Diaphragm Valves, Goyen Diaphragm Valve Repair Kits, Goyen Solenoid Valves
|
|
Chutes & Transitions
Standard Filter has the in house Engineering and Bulk Material Handling expertise to fabricate Custom Chutes and Transitions for Hopper and Silo Discharge and Filling applications. Woven and Non Woven Fabrics such as Cotton, Polyester, Polypropylene, Vinyl, Nomex, Teflon can be utilized to suit practically any solids flow application. Ends can be made to fit stub ends or flanged to mate.
|
|
Ducting
Nordfab QF clipped ducting
is an adaptable, smart looking, easy to fit or extend ducting system. It can be quickly dismantled and reconfigured according to the needs of your site. It is suitable for all general dust extraction applications at ambient temperature and particularly for wood, panel production and furniture manufacture. A complete range of compatible accessories and installation components enable professional installations with economy.
Flanged ducting
in heavier gauges is available for more demanding applications for example with abrasive dusts such as metals and quarry products and also for higher temperature applications including flue gas from foundry processes and incineration.
|
|
| ... products without technical information |
| |
Vertical centrifugal immersion pumps
Seal lots and safe to run dry Solid plastic vertical centrifugal immersion pumps are used predominantly space-saving by direct installation into industrial environments. For strongly crystallizing media, centrifugal immersion Pumps are supplied with a special seal to avoid the penetration of steam and the connected crystallization. Standard depths of immersion are ranging from 200 mm up to 500 mm. Depths of immersion up to 1000 mm are possible by the means of an intermediate bearing
Fluids delivered:
- Acids, bases and mixtures
- Solvents
- Alkaline degreasing baths
- Electroplating baths
- Foto chemicals
- Radioactive, aseptic and precious liquids
- Food stuffs
- Other low-viscosity fluids
Fields of application:
- Electroplating
- Etching and cleaning plants
- Refrigerating machines
- Solar systems
- Sewage and water treatment
- Foto industry
- Textile and food industries, etc.
|
|
|
|
|
|
The centrifugal immersion pumps of building group 4 are used for wet-pit operation in containers, pits and tanks. Centrifugal immersion pumps for dry-well installation, i.e. to be installed and operated outside the container, are also available.
All components of pumps in plastic design that are in contact with the fluid are made of PP or PVDF. The pump shaft consists of a motor shaft made of stainless steel and a shaft-protecting tube of either PP or PVDF. Built-in elastomers are made of FPM (or also EPDM without surcharge). Centrifugal immersion pumps are equipped with overhang shafts so that there is no need to provide for shaft bearings in components that are in contact with the fluid. Thus, the pumps are safe to run dry and do not require regular service and maintenance.
There is no need of a mechanical sealing of the shaft. Only a so-called gas seal is installed beneath the motor to prevent aggressive vapours from penetrating the motor chamber. But this seal is never in contact with the fluid delivered.
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
Parker's IQ200 particle counter is specifically designed to provide continuous, on-line monitoring of the particulate contamination level of hydraulic and lubrication fluids. This compact, affordable particle counter can connect to virtually any system to give the user real-time data at the specified interval. Other features include:
• Remote and multiple system monitoring from one location
• Completely automatic
• Laser accuracy and repeatability
• Programmable test intervals from 3 seconds to 24 hours
• Adjustable contamination level alarms
• Integral flow and calibration check
• ISO 4406-1999 reporting format (4, 6, 14 micron) and correlation to NAS 1638
• User friendly Windows-based software
• Data displayed instantly in chronological or graphic form
|
|
|
|
|
|
Icount Particle Detector
The Icount Particle Detector from Parker represents the most up-to-date technology in solid particle detection. The design dynamics, attention to detail, and small size of the permanently mounted, on-line particle detector brings a truly innovative product to all industry. The laser based, leading-edge technology is a cost effective market solution to fluid management and contamination control.
Features and benefits of the Icount PD include:
• Independent monitoring of system contamination trends.
• Early warning LED or digital display indicators for Low, Medium and High contamination levels.
• Moisture % RH LED indicator (optional).
• Cost effective solution in prolonging fluid life and reducing machine downtime.
• Visual indicators with power and alarm output warnings.
• Continuous performance for dependable analysis.
• Hydraulic, phosphate ester & fuel fluid compatible construction.
• Self diagnostic software.
• Fully PC/PLC integration technology such as: RS232 and 0-5 Volt, 4-20mA.
|
|
|
|
see the results for the following category : 
