|
|
|
The Blancett Frequency-to-Current (F-to-I) and Frequency-to-Voltage (F-to-V) converters are microprocessor-based devices designed to provide an analog output directly from a Blancett turbine flow meter. The converters measure and calculate the flow rate of a turbine flow meter and produce an analog output representative of that flow rate, in the form of a 4-20 mA or 0-5 VDC signal.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
... see all the products in the category
UPSs
|
FemtoPower1060-x-s are passively mode-locked 300 fs fibre lasers operating in the 1060 nm spectral range and delivering up to 5 W of average power.
The lasers consist of a master source, high power fibre amplifier and optical pulse compressor. The lasers are air-cooled, maintenance free and do not require any adjustments.
APPLICATIONS
Fundamental study
Micromachining
Bio-medical
Metrology
|
|
| ... products without technical information |
| |
|
Impressive though the success story of semiconductor lasers has been, there are still several spectral "gaps", wavelengths that cannot be directly accessed with laser diodes. However, nonlinear frequency conversion techniques can be employed to generate tunable laser radiation in the UV, blue and green spectral range. TOPTICA offers state-of-the-art laser systems based on second harmonic generation (SHG), sum frequency generation (SFG) and fourth harmonic generation (FHG).
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
Impressive though the success story of semiconductor lasers has been, there are still several spectral "gaps", wavelengths that cannot be directly accessed with laser diodes. However, nonlinear frequency conversion techniques can be employed to generate tunable laser radiation in the UV, blue and green spectral range. TOPTICA offers state-of-the-art laser systems based on second harmonic generation (SHG), sum frequency generation (SFG) and fourth harmonic generation (FHG).
|
|
The OLFLEX® VFD and VFD-CT cables are now CE and CSA approved, in addition to being UL-listed, making the popular cables ideal for international use.
The semi-conductive material extruded over the cable’s copper forms a spike resistant barrier, eliminating the corona discharge normally resulting from voltage spikes, reflections, and power distortions. Unlike standard power cables, the enhanced VFD power cables are excellent for connecting variable frequency drives to motors, especially in applications that require a voltage rating of 1000 V/2000 V peak.
A 12x minimum bending radius allows the cable to flex and bend in both moderate flexing applications and confined areas. In addition, the cables offer superior oil resistance thanks to its orange PVC outer jacketing.
The OLFLEX® VFD-CT is rated for use in cable trays and features all the benefits of the OLFLEX® VFD. In addition, the cable is flame retardant, UV resistant, and meets NEC and NFPA requirements.
OLFLEX® VFD SLIM is a reduced diameter shielded motor supply cable for variable frequency drives. The materials used are designed to hold up to the non-linear power distortions associated with VFD drives. This cable has a specially blended PVC jacket that is approved for both UL and CSA standards for 600V.
|
|
As power cables only
With one control pair resp. quad
With two control pairs
For Indramat® and Siemens® servo motors
|
|
| ... products without technical information |
| |
The Cloupressor: BOGE SLF
A frequency controlled screw compressor. By changing the speed of both motor and air end the SLF can operate the air end in its specifically optimum range and adapt the compressed air output to the actual needs. Expensive idling times and motor switches are avoided. At the same time a smaller pressure band can be set, also helping to save enrgy.
Special benefit: By adjusting the air end speed by frequency regulation not only the FAD can be adjusted but also the pressure value! Usual frequency controlled screw compressors only change the FAD at a certain given maximum pressure. Lowering the pressure value did not result in a higher FAD. But with the SLF adjusting the pressure value will at the same time result in an adjustment of the maximum possible FAD! This way a 13 bar model easily can be switched to an 8 bar model including the higher volume flow of an 8 bar machine. There are no alterings or constructive changes necessary. All pressure values can be served with one machine.
New models up to 160 kW / 220 PS!
SLF 30 - SLF 221
Direct coupled & oil injection cooled.
Effective FAD: 1,06 - 28,21 m³/min
Pressure range: 8 - 13 bar
Drive rating: 22 - 160 kW
|
|
|
|
see the results for the following category
