|
|
FT-NAM-I-CFG (604 000)
• 6,2 mm. Housing width
• Namur sensor, dry contact inputs
• DIP switch configurable frequency ranges and output signal ranges
• 3 port 1500 VRMS isolation
• High precision conversion
• Wide operating temperature range
• Low power consumption
The FT-NAM-I-CFG configurable frequency transducer converts measured values of namur sensors and dry contacts into standard current and voltage signals or its inverse.
Input type, frequency ranges and output range are field configurable by means of easily accessible dip switches or can be specified when ordering. |
|
| Sluice Gate Drives to open and close sluice gates on canals and rivers. haacon is fabricating sluice gate drives from 1- 40 t load and there are different implementations. Lift and length of rack are individually adjusted to your requirements. Most of our models suit either manual operation as well as electric motor drive. For an individual offer please send the "Checklist for dimensioning a sluice gate drive" entirely refilled back to us. You can load it and further technical data from the haacon site. |
|
| ... products without technical information |
| |
| The Blancett Frequency-to-Current (F-to-I) and Frequency-to-Voltage (F-to-V) converters are microprocessor-based devices designed to provide an analog output directly from a Blancett turbine flow meter. The converters measure and calculate the flow rate of a turbine flow meter and produce an analog output representative of that flow rate, in the form of a 4-20 mA or 0-5 VDC signal. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
... see all the products in the category
UPSs
|
FemtoPower1060-x-s are passively mode-locked 300 fs fibre lasers operating in the 1060 nm spectral range and delivering up to 5 W of average power.
The lasers consist of a master source, high power fibre amplifier and optical pulse compressor. The lasers are air-cooled, maintenance free and do not require any adjustments.
APPLICATIONS
Fundamental study
Micromachining
Bio-medical
Metrology |
|
Diesel engine control meets electric drive system!
HEINZMANN has combined its know how in Diesel Engine Control and in Electric Drive Systems by developing an electric motor/generator for diesel hybrid drives.
As a specialist in control systems for diesel engines, HEINZMANN is now able offer a major contribution to this forward-looking drive technology for the construction vehicle sector.
Description
Operation as a motor, generator or starter
- brushless
- Liquid cooling
Application
Applications for the HYPERION Hybrid Drive include
- wheeled loaders
- forklift trucks
- hydraulic excavators.
It is also possible to install the full-hybrid system in closed rooms, tunnels and aircraft hangers. |
|
The Cloupressor: BOGE SLF
A frequency controlled screw compressor. By changing the speed of both motor and air end the SLF can operate the air end in its specifically optimum range and adapt the compressed air output to the actual needs. Expensive idling times and motor switches are avoided. At the same time a smaller pressure band can be set, also helping to save enrgy.
Special benefit: By adjusting the air end speed by frequency regulation not only the FAD can be adjusted but also the pressure value! Usual frequency controlled screw compressors only change the FAD at a certain given maximum pressure. Lowering the pressure value did not result in a higher FAD. But with the SLF adjusting the pressure value will at the same time result in an adjustment of the maximum possible FAD! This way a 13 bar model easily can be switched to an 8 bar model including the higher volume flow of an 8 bar machine. There are no alterings or constructive changes necessary. All pressure values can be served with one machine.
New models up to 160 kW / 220 PS!
SLF 30 - SLF 221
Direct coupled & oil injection cooled.
Effective FAD: 1,06 - 28,21 m³/min
Pressure range: 8 - 13 bar
Drive rating: 22 - 160 kW
|
|
Ergo XJN/XSN
The sit-on stacker is one of the rider stackers. Gives ergonomic handling at a low cost.
Suitable for mixed handling, stacking/transfer with continuous driving time not exceeding 3 hours.
XJN (Junior) has the smallest turning radius.
XSN (Senior) has the biggest battery.
|
|
| Presto Pallet Stackers are ideal for servicing pallet racks. They are more economical and easier to use than conventional fork lifts. With over 40 models to choose from and a wide variety of available options, there's sure to be a Presto Pallet Stacker to meet your needs. |
|
|
|
see the results for the following category
