Ball shut-off valves

P. 1
Containment Sampling Isolation Valve Model F100-40 For Nuclear Applications

P. 3
3 Design Evaluation Testing Over 45,000 hot cycles and this containment sampling/ isolation valve still exceeds leakage requirements. Purpose The testing at our Lake City, Pennsylvania plant was designed to evaluate the performance of the Copes-Vulcan 3/8" (10mm) Sampling/lsolation Valve

P. 2
2 Features The Copes-Vulcan Model F100-40 valve can solve your leakage problems in critical applications by offering: ? Positive shutoff ? Reliable operation ? Radiation resistant materials ? Fast, easy maintenance ? No need for piping supports or restraints 3/8" (10mm) Sampling Valve

P. 196
» control 1-GATE module - Storage space for 1 module required - Connection of an isolation valve - LED display «READY» - Push buttons «OPEN», «CLOSE» - 12-pole plug for connecting the isolation valve - 19-pole plug for «REMOTE» control 2-GATE module - Storage space for 1 module required - Connection

P. 3
system for pressure control & isolation, integrated controller 118 652 Pendulum valve control system for pressure control & isolation, extended control range 124 95 Combo control valve control and isolation valve in one body C Page Series Transfer valves and doors for SEMI 126 02/03 Transfer valve

P. 125
x y Control valve combined with an isolation valve for pressure control and isolation Series 951: control valve + angle valve - with bellows feedthrough - opening at 1 bar differential pressure possible - compact Series 952: control valve + gate valve - with O-ring shaft seal Body

P. 101
Control and isolation valve General purpose stainless steel valve Adaptive pressure control with stepper motor or throttling by adjustable 3-position pneumatic actuator Throttling gate valve with 3-position pneumatic actuator double acting with position indicator with solenoids Control

P. 95
(input: 100 - 240 V AC, output: 24 V DC / 4 A) 249775 3) Details see chapter «Pressure controller» Downstream pressure control and isolation valve Compact design Fast operation High-performance, integrated controller Low minimum controllable conductance Body material aluminum hard anodized

P. 8
problems due to high velocity through the dryer at low pressures. Allow the dryer to reach system operating pressure. This may take several minutes on larger models. NOTE: On larger models, with air operated inlet valves, open the pilot air isolation valve connected to the inlet tee during start

P. 7
DRYSTAR MANUAL REV: 2-4-10 7 of 14 Section 4 ? Set-Up & Operation 4.1 - PURGE SETTING Verify the purge gage reading corresponds to the setting shown on tag attached to purge valve, as the towers are purging. For adjustable purge units, up to 100 scfm capacity, the purge adjustment valve

P. 9
DRYSTAR MANUAL REV: 2-4-10 9 of 14 Observe the operation of the dryer for at least one complete cycle. The operation at the following points should be closely observed. The right inlet valve opens. (?RIGHT TOWER DRYING? Light is ON) The left inlet valve closes. (?LEFT TOWER DRYING? Light

P. 13
DRYSTAR MANUAL REV: 2-4-10 13 of 14 Section 7 -Troubleshooting PROBLEM REASON CORRECTION No outlet flow No Power Turn power on Damaged solenoid valve Replace valve Plugged filter element Replace element High pressure drop Filters clogged Replace elements Screens clogged Clean screens

P. 4
installation. A three-valve bypass is recommended around all heatless dryers to provide uninterrupted flow during maintenance. Filters must be installed before and after the dryer. Three valve bypasses are recommended for each filter to facilitate changing the elements. Special filter arrangements may

P. 6
pdf filecdr tablemain trrow tdcell divblock divparagraph font0 font 700pt arial sansserif font1 font 1100pt arial sansserif font2 font 1200pt lucida sans unicode sansserif 2 location parts 1 vacuum pump 2 base frame 3 electric motor 4 vacuum gange 5 tyre coupling 6 ball valve 7 stop cock water

P. 19
direct mounting coupling set tyre coupling ball valve off valve stop cock valve water regulating valve common base frame pump motor matching flange fitted pump water strainer brass water line b optionalaccessories b 1 non return valve 2 coupling guard 3 foundation bolt 4 silencer carefully remove

P. 22
times new roman serif b ppis b g drawing discharge flange note 1 item marked is not ppi scope 2 direction rotation clockwise hw usec aa b hx b 12 stop cock water regulating valve 1 11 ball valve water off valve 1 10 base frame pump motor 1 9 matching flance 2 9 vacuum gauge 0760 hg 4 dia dial 3 8 bsp 1

P. 10
2 start electric motor see the direction rotation it should be clockwise looking from the coupling side b never start pump without water always start the water first then pump b 3 regulate the quantity water supply as per pump data sheet means plug stop cock excessive water quantity is also

P. 5
any work the pump shall only be performed when it is standstill b it is imperative that the procedure shutting down the machine described this manual is to be followed pumps pump units which convey hazardous media must be decontaminated completion work all safety protective facilities must be reinstalled

P. 150
Isolation valve Ø 160 mm Isolation valve Ø 200 mm 40375004 40375259 40375273 40375269 40116540 12374400 12374427 High Vacuum Pre-separator Nederman has developed a large number of separators for most materials. • Separation/evacuation of material in large bags. • Discharge of collected

P. 38
the filter cartridges. Mounted on FilterMax stand. 12372063 Filter module Filter module for extra capacity, max. 4 modules in a unit. 12373946 FilterMax F W3 kit Set contains dP control set, filter regulator, shut-off valve, indicator light and plastic bags for dust container. With this set, the Filter Max F

P. 40
supervision. Saves pressured air in some applications with intermittent load. Equipped with alarm function so for high pressure drop over the filter cartridges. 12373603 Shut-off valve Ventilation shut-off valve. Should be installed in the compressed air line. Used to shut off compressed air while the system

P. 37
the right air pressure. Separates dust from compressed air, which means it also protects the valves. Should be installed in the compressed air line. May only be placed in a frost-free environment. 12372064 Shut-off valve for compressed air Ventilation shut-off valve. Should be installed in the compressed

P. 207
30511850 Part no. Extension bar Foot connection Blowback valve Filter Pressure relief valve Ball Valve with filter 27 bar x x x x x Antifreeze x x x x x x Windscreen fluid x x x ExtracEvacuation tion kits with kit probes x x Media Oil Sump oil filter Drum lid Waste oil/Antifreeze Part no. x x Ball Valve x