|
|
ART. 424
2-WAY FULL-BORE THREE PIECE CASTED STAINLESS STEEL BALL VALVE, THREADED-ENDS, BUTT WELD OR T-CLAMP
ART. 429
2-WAY FULL-BORE THREE PIECE CASTED STAINLESS STEEL BALL VALVE, THREADED-ENDS OR BUTT WELD
ART. 434
2-WAY FULL-BORE STAINLESS STEEL BALL VALVE, DIN 11851 FEMALE THREADED-ENDS
ART. 445
3-WAY FLAT BODY FLANGED STAINLESS STEEL BALL VALVE, L PORT
ART. 448
3-WAY FULL-BORE THREADED-ENDS STAINLESS STEEL BALL VALVE, L PORT
ART. 450-451
3-WAY FULL-BORE THREADED-ENDS STAINLESS STEEL BALL VALVE, T OR L PORT
ART. 460-461
3-WAY FULL-BORE FLANGED STAINLESS STEEL BALL VALVE, T OR L PORT
ART. 464-465
3-WAY FULL-BORE STAINLESS STEEL BALL VALVE, T OR L PORT, DIN 11851 FEMALE THREADED-ENDS
|
|
TORK Electric actuated valves are two series
1. Electric actuated ball valve
2. Electric actuated butterfly valve
TORK Electric actuated ball valve,T-EAV900Serie, are two main parts, a quater turn,90 degree turn electric actuator and ball valve. Out put torque value of electric actuator (Nm) , must be more 25%
than out put torque value of ball valve (Nm).
application: ball valves,butterfly valves,dampers,plug valves , on-off or proportional control
|
|
The TITAN 3-piece ball valve, with full bore, is used as an ON-OFF valve for: chemical, water and pneumatic plants, for installations with high interchangeability of components and for steam up to 10 bar. The valves are designed and manufactured in order to allow inspections and maintenances on line by extracting only the body.
|
|
2-PC BALL VALVE,
SS316/304/WCB BODY,
FULL BORE/ REDUCED BORE,
WITH/WITHOUT (DIRECT) MOUNTING PAD ISO5211
THREADED END
|
|
The VENUS ball valve, with full bore, guarantees a high working reliability at low pressure in gas installations: is certified DIN DVGW by the German gas institute, and BRITISH GAS by the British gas institute.
Blow-out proof system, with perfect air bubble sealing, does not need any maintenance. The patented outside sealing system guarantees the maximum reliability during the time.
1 O-Ring in NBR for sealing at low pressure and vacuum.
All valves are tested at 25 bar pressure, for a period longer than 48 hours.
|
|
The ALBA 2-piece ball valve, with full bore, is used as an ON-OFF valve for: chemical products, for water and pneumatic installations, gas, water, vacuum. For steam within limited working conditions and with special seats. All parts have to be adequately degreased if the valve have to be used for oxygen.
Temperature: For fluids from -20C a +150C
Pressure: For fluids from 100 bar to 40 bar
|
|
High pressure ball valves:
This range offeres a reliable option for the high pressure application. These valves are recommended for the use in Oil, gas,petrochemicals where the long life is required.
|
|
2-PC HIGH PRESSURE BALL VALVE
RATING: 6000 WOG/ PN414
FULL BORE, THREADED END
SS316/ SS304/ WCB BODY
WITH/ WITHOUT MOUNTING PAD ISO5211
|
|
3-PC HIGH PRESSURE BALL VALVE
RATING: 3000WOG/ 200BAR
2000WOG/ 130BAR
FULL/ REDUCED BORE
S.S.316/ S.S.304/ WCB BODY
THREADED/ SOCKET/ BUTT WELD
WITH/ WITHOUT API 607 FIRE SAFE
NORMAL/ DIRECT MOUNTING PAD ISO5211
|
|
APPLICATIONS
HCV6 Series valves are ideally suited to mobil
plant and industrial applications, particularly
those involving high pressure pulses. Also
general applications where a robust, high
pressure changeover valve is required.
CONSTRUCTION Body and connector are zinc plated steel. Handle - steel forging, zinc plated. Ball seals - DELRIN (polyacetalic resin) Shaft seal - nitrile.
TECHNICAL DETAILS Pressure rating - up to 500 bar continuous. Operating fluid - mineral oil. Handle travel - 90 arc.
SPECIAL TYPES
We are always pleased to discuss customer
requirements for non-standard valves. Please ask for
our Technical Sales Department.
|
|
General information
* nominal diameters from 4 to 65
* nominal pressures up to 500 bar (7250 PSI)
* with optional pneumatic, electric or hydraulic actuator
* also available with position indicator, limit switch, proximity switch or locking device
* with floating ball
o with threaded connector
o as combination
o with SAE-flange connection
o for manifold mounting
o for manifold insertion as cartridge type
* with trunnion ball
o with threaded connector
o as combination
o for manifold mounting
|
|
The VKD is a True Union ball valve, particularly suitable for industrial applications, where high performances and long time reliability are a must.
The patented Seat Stop system assures great longevity of the seals in situations where vibration or thermal expansion occurs. A micro-adjusting of the PTFE seals is also allowed.
As any accidental loosening of the ball carrier is not possible, the radial dismounting of the valve body can be done in full safety.
The new patented Dual Block system allows a proper nut tightening, without any risk for unscrewing due to vibrations.
|
|
|
Cam-Line plastic-lined trunnion ball valves offer the same proven design benefits as the Cam-Tite product line, including tight shut-off, reliable stem sealing, and unsurpassed torque reductionall unique features in a plastic-lined ball valve design. With special Tefzel or polypropylene linings and option PVDF coatings, Cam-Line ball valves are well suited for highly corrosive applications within the chemical processing industry such as sulfuric and hydrochloric acid.
|
|
The VKD is a True Union ball valve, particularly suitable for industrial applications, where high performances and long time reliability are a must.
The patented Seat Stop system assures great longevity of the seals in situations where vibration or thermal expansion occurs. A micro-adjusting of the PTFE seals is also allowed.
As any accidental loosening of the ball carrier is not possible, the radial dismounting of the valve body can be done in full safety.
The new patented Dual Block system allows a proper nut tightening, without any risk for unscrewing due to vibrations.
|
|
|
|
|
|
Rugged, Compact Design:
Hayward's rugged, low cost QIC2 all plastic PVC ball valves incorporate many design features found only on higher cost ball valves. Features such as PTFE seats, full porting and a 150 PSI pressure rating are all standard on every size of QIC2 ball valves.
Cost Sensitive Applications:
The QIC2 ball valve is perfect for OEM and other applications that require a reliable ball valve at an economical price. The QIC2 valve has been designed and tested to make certain it will perform year in and year out in the most demanding applications without leakage or failure. The internal components of the QIC2 ball valve are completely encapsulated inside the one piece valve body which means that the valve never requires adjustment. The QIC2 valve is ready to be put into service right out of the box.
Lightweight and Compact:
QIC2 lowcost ball valves are designed to fit into spaces too small for other valves. They are about 1/3 the overall size of a true union ball valve and they weigh an average of 50% less. This makes them ideal for skid mounted and other applications where space and weight are critical considerations.
Can't Rust, Won't Corrode:
Their all plastic construction means that they will never fail, stick, or jam because of rusted or corroded parts. And they'll work in places and environments where metal valves must be painted or coated just to survive.
|
|
|
|
|
|
TORK Pneumatic actuated valves are two types
1.Pneumatic actuated ball valves
2.Pneumatic actuated butterfly valves
click fore more information http://www.sms-tork.com.tr/default.aspx?pid=51091&grpID=6608
T-PAV 900 Series Pneumatic Actuated Valves;
double acting actuated ball valves and single acting actuated ball valve ,3 position actuated ball valves
TORK Pneumatic actuated valves accessories :
1)solenoid valves, 5/2 or 3/2 way(namur standard or standard type).
2)Limit switch box (shows valve position,and takes electrical signal )
3)positioner(proportional control application)
4)mounting kits(non standard valves)
5)Ex-proof solenoid valves
6)manuel ovirride
7)I/P Converter and PID control panel
TORK ball valves;
Flange,screwed,welding connection,or mono block body. way : 2/2 and 3/2 ,
body: brass,stainless steel,PVC, carbon steel,carbon casting
TORK pneumatic actuators ; double acting,single acting,3 position,180 degree turn.
Ball valve specifations: valve size,connection type of valvei,valve pressureclass,fluid pressure,valve way,valve body meterial, fluid type,fluid temperature, howmany pcs should valve open-close per day after ball valve can be select.
Certificates:CE(TUV) , ISO9001:2000 TUV, GOST, TSEK, LOYD,UNSEPRO
|
|
1-Piece, Instrumentation, 40 Series Ball Valves
1-Piece, Instrumentation, 40G Series Ball Valves
2-Piece, Instrumentation 33 Series Ball Valves
3-Piece, Alternative Fuel Service, High Pressure (up to 6000 psig [413 bar])
3-Piece, Instrumentation, High-Pressure (up to 10 000 psig [689 bar]), 83 Series Ball Valves
3-Piece, Multipurpose SK Series Ball Valves
3-Piece, Process / Instrumentation, 60 Series Ball Valves
|
|
Ultra Purity
Product standards:
Technical indicators:
Working pressure: 10kg/ c
Durability test: 5000 cycles
Inboard leaking rate: 1x 10-9 atm cc/sec
Internal leaking rate: 1x 10-9 atm cc/sec
Outboard leaking rate: 1x 10-9 atm cc/sec
Performance demand:
The leaking rate meets the SEMI F1 standards
under the technical indicators circumstances
mentioned above.
|
|
|
|
|
|
Any leakage of gas or liquid has to be avoided at all cost. SOMAS ball valve is designed to take care of this issue. The valve is a full bore, flanged ball valve with cylindrical bore made in dimensions from DN 25 to DN 400. The valve is made from stainless steel with spring loaded seats for good tightness, even at low differential pressure.
The valve ball is hardchromed as standard, but can also be supplied with Hi-Co coating. The valve can be supplied with actuator and accessories for manual operation, on/off or control applications.
Ball valves also in 3-piece form
SOMAS 3-piece full-bore ball valves are mainly intended for use as manually operated valves or remotely actuated on/off valves. The ball valve meets ISO standards.
The valve is available with threaded ends, welding ends or flanges. It is also possible to combine different types of ends.
SOMAS 3-piece full-bore ball valves are equipped with seats of two materials. Fibreglass-reinfoced PTFE as standard, or carbon-filled PTFE adapted for steam.
|
|
For operating under full pressure!
For use at extremely high pressure (ex. high pressure water jet-technology) Rtelmann offers ball valves made of high-tensile chrome molybdenum steel with a nominal pressure of PN 2.500 (nominal size DN 10).
|
|
3-way Plug Valves
TUFLIN 3-way Plug Valves for complex piping systems
The design and sealing principle of the TUFLIN 3-way plug valve is based on the proven 2-way plug valve design. All configurations are suitable for more flexible and complex piping systems and applications.Typical applications of multiport plug valves:
* as changeover valves for pressure relief duties
* for by-pass or mixing operation purposes
* as switchover valves for filtration circuits
* in the pulp and paper industry
* in filtration or drying plants
|
|
TYPE FLOATING, TRUNNION
SIZE RANGE 1/4 TO 32
BONNET TYPE SIDE ENTRY, TOP ENTRY, 3PCS, FULLY WELDED
MATERIAL A105, F11, F22, F5, F9, F304, F304L, F316, F316L, F44, F51 &
SPECIAL ALLOY, WCB, WC6, WC9, C5, C12, CF8, CF3, CF8M, CF3M,
CF8C, CF10, DUPLEX, INCONEL, MONEL, HASTELLOYetc
PRESSURE RANGE CL 150 TO 2500
ENDS SCREW, SOCKET WELD, BUTT WELD
FLANGE: ANSI, JIS, DIN
OPERATOR LEVER, CHAIN LEVER, WARM GEAR, PNEUMATIC, HYDRAULIC, MOTORIZE
|
|
Ball Valves
The ball valves are indicated for the use with various types of liquids, gases and steam in a broad temperature range and pressure according to ASME B 16.34 rule.
- Activation by one-fourth round (90), reducing the valve opening and closing time;
- Two part construction, which eliminates high operation torque and avoids damage to the sealing parts;
- Three part construction (body and two covers) making maintenance easier with no need to disconnect the line ends;
- Explosion-proof stick, offering higher safety while operating, gasket maintenance;
- Sealing available in PTFE and COMPL;
- Also available in double-sealing construction, which provides higher safety when used in steam lines;
- Installation in any position.
|
|
Valves
Product range
DIN & ANSI
gate, globe, check, piston valves, diaphragm valves, tank bottom valves, plug valves, ball valves, butterfly valves
Connectors, fittings & instrumentation
fittings, instrumentation valves, pressure & temperature gauges
Safety relief valves
safety valves, flame arrestors, strainers, locking devices
Steam control and conditioning equipment
steam traps, measurement instruments, separators & condensate recovery systems, boiler valves, level gauges, sight glasses
Solenoid valves & control valves Specials
quick opening closures, complete launcher/receivers, hub-ends
|
|
Combustion Control Accessories Ball Valves (BV)
(10)
Ball valves are used to provide positive manual shut off of fuels in combustion systems.
Ball valves are UL listed and rated at 250 psi (1720 kPa) for fluid temperatures up to 400 F (204 C). Ball valves in this series are suitable for natural gas, LP gas and fuel oils. All valves feature NPT connections.
|
|
Schwer Fittings offer a complete range of reliable and proven stainless steel valves and fittings. The many different types cover a wide range of uses, pressures, temperatures and mediums.
sf-Ball Valves
A 90 rotation of the spindle moves the ball from the open flow position to closed. The pressure in the system presses the floating ball against the rounded seal on the outlet side, thereby making a leak-free seal.
Advantages:
The position of the lever shows clearly whether the valve is open or closed
Full open passage
Seal made through floating ball
|
|
Metal Ball Valves
XOMOX offers a complete metal ball valve line for numerous industries and applications. We supply ball valves in 2-way and multi-way design, special ball valves and customer tailored valve solutions.
As standard we offer flanged, compact and three-piece ball valves. Special ball valves (e.g. ball valve safety couplings,) complete our comprehensive metal ball valve range.
In addition to the standard seal made of virgin or reinforced PTFE we equip our ball valve products with a broad line of special soft and metal seals for demanding duties such as high temperatures and pressures, corrosive and abrasive flow media.
All packing materials and body seals will get selected and adjusted to meet your specific working conditions.
|
|
Specs: DN20-150C1-6
StandardFDINASMSAISO
MaterialFSUS304ASUS316L
ApplicationFbeer CDairy IndustryCbeveragesCpharmaceutical
|
|
CRYOGENIC VALVE
TYPE GATE, GLOBE
SIZE RANGE 1/4 TO 24
BONNET TYPE BOLTED, WELDED
MATERIAL F304, F304L, F316, F316L, CF8, CF3, CF8M, CF3M
PRESSURE RANGE CL 150 TO 1500
ENDS SCREW, SOCKET WELD, BUTT WELD
FLANGE: ANSI, JIS, DIN
OPERATOR HANDWHEEL, CHAINWHEEL, BEVEL GEAR, PNEUMATIC, HYDRAULIC, MOTORIZE
|
|
|
|
