|
|
Split body floating ball valve
ND (nominal diameter): 4-200
other diameters or pressures under request
NP (nominal pressure): 6-160
MAIN TECHNICALS SPECIFICATIONS
Execution : A105, AISI 316, ISO, ANSI 515.
Can have risen with any types of actuators
Connection of actuators following one ISO 5211
Anti-statique
Management of the fluid in both senses
Technology: Forged
Principle: 2 pièces
|
|
CONSTRUCTION
Full bore in L, T, or X, floating ball, supported by four seats, high performance low emission double stuffing box, relief seats, anti-static device, fire safe, pressure balance hole in ball, blow-out proof stem.
CHARACTERISTICS
High performance low emission double stuffing box.
Internal wetted parts are in acc. to NACE Standard MR0175
|
|
CONSTRUCTION
Full bore, fully welded body, floating ball, high performance low emission double stuffing box, relief seats, anti-static device, fire safe, pressure balance hole in ball, blow-out proof stem.
CHARACTERISTICS
High performance low emission double stuffing box.
Internal wetted parts are acc. NACE Standard MR0175.
OPTIONS
API 6D
GN - PE EM-D20-E (Gas Natural S.d.G.)
|
|
CONSTRUCTION
Full bore, fully welded body, floating ball, high performance low emission double stuffing box, relief seats, anti-static device, fire safe, pressure balance hole in ball, blow-out proof stem.
CHARACTERISTICS
High performance low emission double stuffing box.
Internal wetted parts are in acc. to NACE Standard MR0175.
|
|
CONSTRUCTION
Reduced bore, one piece body, floating ball, high performance low emission double stuffing box, relief seats, anti-static device, fire safe, pressure balance hole in ball, blow-out proof stem.
CHARACTERISTICS
High performance, low emission double stuffing box.
Internal wetted parts are acc. NACE Standard MR0175.
|
|
Series 040/050 - DN06 to DN50 PNO-16
Available with DVGW registration stampings
Fields of application :gas
|
|
Hydratron can supply from stock a wide range of High Pressure Ball Valves suitable for either gas or liquid service at pressures of up to 20,000 PSI (1,400 Bar )
Valves can be supplied with NPT, Medium Pressure, or High Pressure connections with wetted parts manufactured from 316 Stainless Steel.
Both 3 and 2 way models are available which can be fitted with air actuators if required.
|
|
Series 700 - DN13 to DN25
Body, ball, stem : steel or stainless steel. 1.4571
Fields of application:
hydraulics, high pressure cleaning systems, press vehicles, pressure test equipment (Seats and seals adapted to application)
|
|
The GHILUX ball valves are shutoff valves type ON-OFF. The opening and closing functions are made by hand, acting on the control spindle of the ball with the handle, or operated with a spanner or screwdriver.
The main characteristics of these valves are the different versions and the reduced dimensions, which have been carefully studied
British Gas approved
The ball valves are available in the following sizes:
tube from 6 up to 18;
thread of 1/8 to 3/4.
|
|
Beswick Engineering now offers a series of miniature ball valves in standard shut-off (MBV-1010), 3-way diverting (MBVT-1010) and 3-way mixing diverting (MBVMD-1010) configurations. Designs offer compact size, light weight and non-restricted flow and are an outstanding choice for applications up to 250 psig.
The standard shut-off valve weighs approx. 9 grams in stainless steel and the 3-way diverting and 3-way mixing diverting valves weigh approx. 12 grams in stainless steel. The mixing diverting valve allows either port to be individually selected or both ports to be simultaneously selected with no shut-off. All of these valves utilize 316 SS ball elements and are available with a variety of seals. Inlet and outlet ports are 10-32 UNF standard, with other sizes available on request.
Body Material: 303 or 316 stainless steel.
Seals: Buna-N. Optional Materials: EPDM, Viton®.
|
|
The J+J electric actuator is widely used in the plastic valve market because it has a plastic housing making it light in weight, and as it has more standard features than any of its rivals, offers exceptional value.
The new J3 Series electric actuators offer an LED status light and plug & play conversion kits that change the function from on-off to failsafe, or modulating, or both.
|
|
2-Way Poly KZValve (shown with KZCO's EH2 actuator)
VALVE FEATURES:
- Valve Sizes from 3/4" to 2" Full Port Single Valves
- Valve body available in poly or nylon
- Ball and Stem: 316SS
- Seat: Virgin PTFE
- Stem Seal: Dual VITON O-Ring
- Body Seals: EPDM
- Max PSI 150 @70F (Poly)
- Max PSI 300 @70F (Nylon)
- Wiring (most configurations available)
- FNPT or Flanged outlets available
- Quick Hairpin (QH)(1" Only)
ACTUATOR FEATURES:
- High quality, durable actuator housing rated NEMA 6P for waterproof applications and NEMA 7D for Ignition Protection applications
- 12/24 VDC and 24 VAC operation available
- Tough aluminum gear box with metal gears
- Actuator housing available with "indicator flag" or with "blank" lid
- Waterproof wire plug connectors
- Private labeling available
Consult our Engineering or Sales staff for application assistance.
|
|
|
Top-Flo® sample valves are specially engineered to be the finest in the industry and incorporate many features and benefits not found on other sampling valves. Top-Floreg; sampling valves come standard with minimal internal deadleg area designed into each valve, keeping hold up volume to a minimum for accurate samples every time. Right Angle or In-Line models can be supplied as main components (special bored cap and main body) to allow the user to fabricate their own size configurations on an as needed basis. Right Angle or In-Line models available from stock in sizes 1/2" to 4" clamp end x hose barb.
|
|
Series 020 - DN04 to DN50
Body, ball, stem : stainless steel. SS316Ti
Fields of application:
chemical and petrochemical industry, environmental installations, off-shore, water, high pressure cleaning systems (Seats and seals adapted to application)
|
|
BuTech Pressure Systems offers an extensive line of check valves, needle valves, 2-, 3-, 4- and 5-way ball valves with 3/16" to 1" ports (4.7mm to 25.4mm), as well as fittings, tubing and related equipment for petroleum production.
Our sub-sea valves are custom designed for instrumentation, process control and chemical injection applications in the harshest environments. Designed for Remote Operated Vehicle (ROV) operation, these valves provide rugged protection, safety and reliability in template control panels, sub-sea wellheads and christmas trees.
Manufactured to meet the requirements of NACE MR-01-75, API spec. 6A and 17D, and numerous other specifications, BuTech sub-sea valves ensure trouble-free operation in hydrogen sulfides, corrosion inhibitors, paraffin thinners, hydraulic fluids and many other chemicals.
|
|
Trunnion ball valve
ND (nominal diameter): 25-800
other diameters or pressures under request
NP (nominal pressure): 6-420
MAIN TECHNICALS SPECIFICATIONS
Execution : A105 or 316L
Double floating seats
Sets of table linen anti-blow of ram and replaceable
Three gaskets
Anti-statique
Anti-feu according to standard API 6 FA / API 607 / BS6755
Traffic of the fluid in both senses
Technology: Molded or Forged
Principle: Sphère arbrée
|
|
Instrument Ball Valve:
Features:
• 2 way ON-OFF valve, 3 way and 5 way switching valve and 4 way cross over valve models are made.
• One-piece ball stem eliminates backlash to ensure alignment of ball and orifice.
• Blowoutproofbottomloadedstem.
• Heavy directional black unbreakable handle
• Panel mounting facility and low operating torque
• Series of end connections W 3/8", 1/2" double or single ferrule tube end or male/female NPT, BSP pipe end.
• Pressure rating up to 2000psi at 100 F
• Material of construction: SS 304/316, Brass.
• 100% factory tested.
|
|
Specifications:
- Pressure Rating: 125 PSI air
- Temperature Range: 40 F to 140 F
- Two piece, Full port valve with threaded ends
- Handle: Tamper proof lockout feature locks in the closed position only
- Exhaust port is tapped 10-32 UNF thread for mounting mufflers or to direct air
|
|
3-PC SANITARY BALL VALVE
SS316 BODY, FULL BORE, BUTT WELD OR CLAMP END
WITH OR WITHOUT POLISH OUTSIDE,
WITH/WITHOUT (DIRECT) MOUNTING PAD ISO5211
1000WOG, USED FOR FOOD/SANITARY PIPE LINE
|
|
General information
* high-grade materials like steel, stainless steel or aluminium
* for pressures up to 1500 bar (21750 PSI)
* with optional pneumatic, electric or hydraulic actuator
* also available with position indicator, limit switch, proximity switch or locking device
* with threaded connector
o with DVGW-approval
o with removable centre
o with automatic pressure relief
o with additional miniature test point outlet
o as combination
o with spring-return and integrated check valve
o for support cylinder control
+ with integrated, pilot-operated check valve
+ without check valve
* with flange connection
o with SAE-flange connection
o with DIN-flange connection
* with welding-end
o with removable centre
* with staple-lock connector
* for manifold mounting
* for manifold insertion as cartridge type
|
|
3 WAY/4 WAY BALL VALVE
THREADED END OR FLANGED END
WITH OR WITHOUT (DIRECT) MOUNTING PAD ISO 5211
1000 WOG OR DIN PN16/40/ANSI 150L
STANDARD /FULL BORE
PORT TYPE: L/T/X
|
|
TRIFLUX series is available both with L and T bore and allows to divert the flow in all directions including the inlet shut off, applicable to each of the three threaded ends. It is suggested for gas and water distribution, industrial and civil heating, water plants at medium pressure, hydraulics and pneumatic, non aggressive media and vacuum.
|
|
|
|
|
|
Flow Patterns:
Hayward Manual Three-Way Ball Valves come standard with a two port "TW" ball allowing for three flow configurations within 180 degrees of rotation. With the bottom port as the inlet, the flow can be directed out the left port, out the right port or shut off. Hayward Actuated Three-Way Ball Valves come standard with a three port "NT" ball allowing for two flow configurations within 90 degrees of rotation. With the bottom port as the inlet, the flow can be directed out the left port or out the right port, there is no shut off position. A "TW" ball, used with with the proper electric actuator, adds what is typically called a "center off position" to the "NT" flow pattern of actuated valves. An optional "TP" ball, used with either manual or actuated valves, allows flow through all ports at the same time or flow shutoff.
True Union Design:
This makes these valves very easy to maintain by allowing for easy removal from a piping system without breaking down the piping connections. Just unscrew the three assembly nuts and lift the valve body out of the line.
Easy to Actuate:
A manual valve can be easily automated. Just remove the handle and install the optional actuator mounting kit. The mounting saddle is integrally molded into the valve body. For rock-solid actuator mounting, the valve incorporates a unique design whereby the mounting bracket mounts directly to the valve body. This assures proper alignment of the actuator to the valve without creating any damaging side loads to cause premature stem seal failure.
No Metal, No Corrosion:
Hayward all plastic three-way valves contain no metal parts. The valves will never fail because of corrosion and they do not require painting or epoxy coating to stand up to aggressive environments.
|
|
GENERAL DESIGN
The floating ball is held between two pre-compressed
seals which ensure a tight, non-leak fit at both positive
and negative pressures. The ball’s rotational angle is
constrained by a stop pin and disc.
Cranked handles are incorporated to provide good
clearance for the operators hands.
Flat handles can be provided on request.
FEATURES Full bore valves provide an unrestricted flow path for
negligible pressure drop. Floating ball on pre-compressed seals minimises
wear and provides an excellent seal at positive and
negative pressures. High working pressures - see table on page 59. Operating temperatures from -20°C to +100°C.
1
4 Open to close in
/ turn (90°).
|
|
|
|
|
|
PNEUMATIC / MANUAL BALL VALVES
The ball valves BUROCCO INOXVALVOLE are charaterized by their innovative shape and adopted technical solutions.
- Up to 5 utilizing ways.
- Autoadjustable gaskets on ball and stem.
- Rotating stem and ball on bearings in PTFE opportunely modified for the utmost working precision and the life of the seat balls.
- Valve dismantling without removing the pipes.
- Rapid replacement of seat balls and stem gasket.
- 2 way versionwith rotation in any position on 360°C even after the installation.
- Besides 3-4 way valves it is possible to have a version with way on the ball rotation axle which extends the application field of the valve considerably, for example: 2-3- way angle, 2-3-4 way with drain, sample collection or data receipt (temperature, pressure, capacity, etc.); 2-3-4-5 way with washing.
- Special applications in combination with on/off, unidirectional and safety valves, with filters, etc.
- Possibility to seal the interspace between ball and body valve through injection of material inert to corrosive fluids (max working temperature 80 °C).
- Application of connections for pressure washing interspace ball/body during the normal working cycle, avoiding contamination among differerent fluids.
|
|
Cepex offers a complete range of ball valves in PVC-U and PVC-C (both manual and automatic), featuring the "Antiblock" system which prevents ball jamming. Valves are 100% hydro tested prior to leaving the factory, and their reliability is further guaranteed by the world's premier certification institutes.
Ball valves are available in accordance with several dimensioning standards (Metric, BSP, ASTM, NPT, British Standard, JIS...) in order to meet the requirements of any market.
|
|
The TOTAL ball valve, with full bore, is an extremely robust product with perfect air bubble sealing
does not need any maintenance, is equipped with wrapping seats ensuring long life cycles. The patented outside sealing system guarantees the maximum reliability during the time.
The valve is approved according the DIN-DVGW standards: such approval was obtained for the first time in 1974 and then always renewed up to the present one. All valves are tested at 25 bar pressure, for a period longer than 48 hours.
|
|
|
Cam-Tite ball valves are engineered to provide the very best performance for demanding hazardous and corrosive applications. Designed to overcome such inherent valve problems as high operating torque and stem leakage, Cam-Tite ball valves feature a unique, non-spherical ball with a bevel at the lip of the port. This configuration minimizes pressure on the seating areas, thus reducing cold flow and prolonging seat life.
|
|
|
The Legris range of ball valves, including standard, axial, and needle valves, provides a reliable means of opening and closing fluid systems.
|
|
|
|
