|
|
Applications:
Suitable for the following processes: hand cutting, sheet
metal cutting, rivet cutting, heating and gouging.
|
|
The right angle flow control is an ideal solution to cylinder speed control where space is at a premium.
FEATURES:
Costly fittings, connections and piping can be eliminated because the valve can rotate 360° and then can be locked into place when the desired position is achieved
Provide meter out control of exhaust air from an air cylinder while providing full flow in the reverse direction
Cylinder port sizes of M5 (10-32) to 1/2"
Inlet port sizes of M5 (10-32) to 1/2" NPT or 5/32" to 3/8" Instant Tube Connector
145 PSI maximum pressure
Temperature range of 0° to 140°F (-18° to 60°C)
|
|
TORK Electric actuated valves are two series
1. Electric actuated ball valve
2. Electric actuated butterfly valve
TORK Electric actuated ball valve,T-EAV900Serie, are two main parts, a quater turn,90 degree turn electric actuator and ball valve. Out put torque value of electric actuator (Nm) , must be more 25%
than out put torque value of ball valve (Nm).
application: ball valves,butterfly valves,dampers,plug valves , on-off or proportional control
|
|
Bex LA - Flush Mounted Ball Valves
LA valves are designed to be used on suspended fluids in the pulp and paper industry. The vave is aimed to meet some basic demands.
In sampling applications it must deliver a tru part of the main flow.
In drainage applications there must be no risk of clogging.
Installed the valve must not cause any heavy dynamic stress to the pipe or the wel
To meet the demands the fluid ahead of the ball must continuously be renewed. The ball must in practice be a part of the pipe wall. The flow ahead of the ball must also be turbulent and at very low velocity the fluid must be mobile. The design of the weld-on flange that is thin and with a conical entrance facing the ball ensure the function.
In drainage applications the fluid can be standing in front of the ball. The fluid can not be allowed to dewater into the valve body as normal for a ball valve. Fibers that get wedged between the ball and the upper seat ring can initiate a clogging problem. Of this reason the LA valve will always have a cavity filler around the ball.
La valves are designed to add as low weight as possible to the pipe wall and the welding. The weld-on flange is thin has a low weight and is easy to handle. The valve body will add a low weight to the weld-on flange and the center of gravity will be close to the pipe wall. The dynamic stress on the pipe and the welding will be low.
|
|
2-PC BALL VALVE,
SS316/304/WCB BODY,
FULL BORE/ REDUCED BORE,
WITH/WITHOUT (DIRECT) MOUNTING PAD ISO5211
THREADED END
|
|
The VKD is a True Union ball valve, particularly suitable for industrial applications, where high performances and long time reliability are a must.
The patented Seat Stop® system assures great longevity of the seals in situations where vibration or thermal expansion occurs. A micro-adjusting of the PTFE seals is also allowed.
As any accidental loosening of the ball carrier is not possible, the radial dismounting of the valve body can be done in full safety.
The new patented Dual Block® system allows a proper nut tightening, without any risk for unscrewing due to vibrations.
|
|
2-Way Poly KZValve (shown with KZCO's EH2 actuator)
VALVE FEATURES:
- Valve Sizes from 3/4" to 2" Full Port Single Valves
- Valve body available in poly or nylon
- Ball and Stem: 316SS
- Seat: Virgin PTFE
- Stem Seal: Dual VITON O-Ring
- Body Seals: EPDM
- Max PSI 150 @70F (Poly)
- Max PSI 300 @70F (Nylon)
- Wiring (most configurations available)
- FNPT or Flanged outlets available
- Quick Hairpin (QH)(1" Only)
ACTUATOR FEATURES:
- High quality, durable actuator housing rated NEMA 6P for waterproof applications and NEMA 7D for Ignition Protection applications
- 12/24 VDC and 24 VAC operation available
- Tough aluminum gear box with metal gears
- Actuator housing available with "indicator flag" or with "blank" lid
- Waterproof wire plug connectors
- Private labeling available
Consult our Engineering or Sales staff for application assistance.
|
|
The VKD is a True Union ball valve, particularly suitable for industrial applications, where high performances and long time reliability are a must.
The patented Seat Stop® system assures great longevity of the seals in situations where vibration or thermal expansion occurs. A micro-adjusting of the PTFE seals is also allowed.
As any accidental loosening of the ball carrier is not possible, the radial dismounting of the valve body can be done in full safety.
The new patented Dual Block® system allows a proper nut tightening, without any risk for unscrewing due to vibrations.
|
|
TORK Pneumatic actuated valves are two types
1.Pneumatic actuated ball valves
2.Pneumatic actuated butterfly valves
click fore more information http://www.sms-tork.com.tr/default.aspx?pid=51091&grpID=6608
T-PAV 900 Series Pneumatic Actuated Valves;
double acting actuated ball valves and single acting actuated ball valve ,3 position actuated ball valves
TORK Pneumatic actuated valves accessories :
1)solenoid valves, 5/2 or 3/2 way(namur standard or standard type).
2)Limit switch box (shows valve position,and takes electrical signal )
3)positioner(proportional control application)
4)mounting kits(non standard valves)
5)Ex-proof solenoid valves
6)manuel ovirride
7)I/P Converter and PID control panel
TORK ball valves;
Flange,screwed,welding connection,or mono block body. way : 2/2 and 3/2 ,
body: brass,stainless steel,PVC, carbon steel,carbon casting
TORK pneumatic actuators ; double acting,single acting,3 position,180 degree turn.
Ball valve specifations: valve size,connection type of valvei,valve pressureclass,fluid pressure,valve way,valve body meterial, fluid type,fluid temperature, howmany pcs should valve open-close per day after ball valve can be select.
Certificates:CE(TUV) , ISO9001:2000 TUV, GOST, TSEK, LOYD,UNSEPRO
|
|
BVH22
G1/4" - 3", DN10 - 80, PN63
Construction : 2-parts
Body / ball : 1.4408 / 1.4401
Connection : female thereaded
Actuator : handlever
BVH23
G1/4" - 4", DN10 - 100, PN40/63
Construction : 3-parts
Body / ball : 1.4408 / 1.4401
Connection : female thereaded, welding ends, flanged ends
Actuator : handlever
BVA23
G1/4" - 4", DN10 - 100, PN40/63
Construction : 3-parts
ISO-top fl ange
Body / ball : 1.4408 / 1.4401
Connection : female thereaded, welding ends, flanged ends
Actuator : pneumatic, electric
BVT/L34
G1/4" - 3", DN10 - 80, PN63
Construction : 3 ways
ISO-top fl ange
Body / ball : 1.4408 / 1.4401
Connection : female thereaded
Actuator : handlever, pneumatic, electric
BVC21
DN15 - 100, PN16/25/40
Construction : Compact-wafer
ISO-top fl ange
Body / ball : 1.4408 / 1.4401
Connection : flanged ends
Actuator : handlever, pneumatic, electric
BVO22
DN15 - 300, PN16/40
Construction : 2-parts
ISO-top flange
Body / ball : 1.4408 / 1.4401
Connection : fl anged ends
Actuator : handlever, pneumatic, electric
|
|
The Model 6B and 10B Ball Valve of 2 piece design which gives higher strength and integrity. We have incorporated the same dynamic multi-ring gland system as in the needle valve, which when combined with the anti - blowout back seating stem, guarantees resistance to all operating processes and pressures.
Key Benefits are as follows :
Over designed high strength adaptor threads combine with soft parent metal bottom seal to give closure thread protection and ensures environmental safety.
Gland and stem leakage a thing of the past due to the dynamic multi-ring gland system, combined with the anti blowout back seating stem.
Precision cut CNC threads banish the problem of thread leakage, and the 100% 4 stage inspection means precise connectivity.
Super finished ball, floating within dynamic self relieving seats, offers dynamic response to fluctuating process pressures. This maintains 100% bubble tight seat closure in both directions.
|
|
1-Piece, Instrumentation, 40 Series Ball Valves
1-Piece, Instrumentation, 40G Series Ball Valves
2-Piece, Instrumentation 33 Series Ball Valves
3-Piece, Alternative Fuel Service, High Pressure (up to 6000 psig [413 bar])
3-Piece, Instrumentation, High-Pressure (up to 10 000 psig [689 bar]), 83 Series Ball Valves
3-Piece, Multipurpose SK Series Ball Valves
3-Piece, Process / Instrumentation, 60 Series Ball Valves
|
|
Spherical faucet wafer
DNN (Nominal Diameter): 10-200 (other diameters and pressures on requests)
PN (Pressure rating): 6-100
TECHNICAL MAIN FEATURES
- Execution: A105, AISI 316
- Can be gone up with all types of actuators
- Connection of the actuators according to ISO 5211
- Anti-static
- Direction of the fluid in the two directions
- Technology: Forged
- Principle: Wafer/sandwich
Markets:
Chemistry
Hydroelectric
Oil/gas
Connection: Between flanges
Type of connection:
- ANSI
- PN/ISO
Passage: Integral
|
|
Faucet with cryogenic floating sphere
- DNN (Nominal Diameter): 15-200
- PN (Pressure rating): 16-100
Technology: Forged
Principle: 2 parts
Markets:
- Cryogenics
- Oil/gas
Connection:
- Has flanges
- To weld
|
|
Faucet with floating sphere 2 parts
DNN (Nominal Diameter): 4-200 (other diameters and pressures on requests)
PN (Pressure rating): 6-160
TECHNICAL MAIN FEATURES
- Execution: A105, ISO, ANSI 515 or AISI 316
- Can be gone up with all types of actuators
- Connection of the actuators Iso 5211
- Anti-static
- Direction of the fluid in the two directions
Technology: Forged
Principle: 2 parts
Markets:
Chemistry
Hydroelectric
Oil/gas
Connection: With flanges
Type of connection:
- THUS
- PN/ISO
Passage:
- Integral
- Reduced
|
|
Faucet with shaft sphere
DNN (Nominal Diameter): 25-800 (other diameters and pressures on requests)
PN (Pressure rating): 6-420
TECHNICAL MAIN FEATURES
Execution: A105 or 316L
Double floating seats
Gaskets anti-blow of ram and replaceable
Triple seals
Anti-static
Fire-resistant according to API standard 6 FA/API 607/BS6755
Circulation of the fluid in the two directions
Technology: Moulded or Forged
Principle: Shaft sphere
|
|
3-way Plug Valves
TUFLIN® 3-way Plug Valves for complex piping systems
The design and sealing principle of the TUFLIN® 3-way plug valve is based on the proven 2-way plug valve design. All configurations are suitable for more flexible and complex piping systems and applications.Typical applications of multiport plug valves:
* as changeover valves for pressure relief duties
* for by-pass or mixing operation purposes
* as switchover valves for filtration circuits
* in the pulp and paper industry
* in filtration or drying plants
|
|
Valves
Product range
DIN & ANSI
gate, globe, check, piston valves, diaphragm valves, tank bottom valves, plug valves, ball valves, butterfly valves
Connectors, fittings & instrumentation
fittings, instrumentation valves, pressure & temperature gauges
Safety relief valves
safety valves, flame arrestors, strainers, locking devices
Steam control and conditioning equipment
steam traps, measurement instruments, separators & condensate recovery systems, boiler valves, level gauges, sight glasses
Solenoid valves & control valves Specials
quick opening closures, complete launcher/receivers, hub-ends
|
|
Bronze Ball Valves
Two-Piece Body • Full Port • Bronze Trim • Single Union Ends • Blowout-Proof Stem
600 PSI/41.4 Bar Non-Shock Cold Working Pressure 150 PSI/10.3 Saturated Steam
|
|
Metal Ball Valves
XOMOX offers a complete metal ball valve line for numerous industries and applications. We supply ball valves in 2-way and multi-way design, special ball valves and customer tailored valve solutions.
As standard we offer flanged, compact and three-piece ball valves. Special ball valves (e.g. ball valve safety couplings,) complete our comprehensive metal ball valve range.
In addition to the standard seal made of virgin or reinforced PTFE we equip our ball valve products with a broad line of special soft and metal seals for demanding duties such as high temperatures and pressures, corrosive and abrasive flow media.
All packing materials and body seals will get selected and adjusted to meet your specific working conditions.
|
|
The SOMAS ball valve type SKV is designed to meet the demands from the process industry.
The design is a flanged full bore valve in sizes DN 25-400 mm (1-16 inch).
The pressure rating is PN 50 (ANSI 300) for DN 25-50 and PN 10-25 (ANSI 150) for DN 80-400. The material is stainless steel with hard chrome plated ball as standard. As option the ball can be HiCo-coated.
The valve has a cylindrical bore that’s gives a minimum of turbulence and a maximum of capacity.
The seats are made from PTFE 53 or HiCo (High Cobolt alloy) and due to spring loaded seats the valve offers a good tightness also at low differential pressure.
The valve is delivered with actuator and accessories for hand operation, on/off operation or for control application.
Beside the type SKV, SOMAS also have a range of 3-piece ball valves type S36. The valve is available with threaded ends, type S36FBG or with welding ends, type S36FBS or with flanges, type S36FBF. It is possible to combine different types of ends.
It is a full bore ball valve in stainless steel with ISO connection for actuators and with two alternative seat materials, PTFE or PTFE re-inforced with glass fibre.
The valve is delivered for hand manoeuvre or equipped with different type of actuators for on/off control.
The SOMAS S36 valve is suitable for most liquids and gases within process industries.
|
|
The P21 High Performance Spherical Disc Valve is designed to meet tomorrow's demanding requirements for containment of solids, powders and slurries. Engineered for pressure assisted sealing from full vacuum to 150 PSI. GEMCO valves use a spherical disc which moves across the seat wiping material away from the sealing area. This self wiping action eliminates pinch points - the source of most valve wear. The P21 is offered with standard ANSI or DIN flanges and ISO actuator mounting.
|
|
SchuF invented the Lift Plug Valve in 1914. Since then, it has delivered plug valves to the Chemical, Refinery, Delayed Coking, Polymer, Cement, Mining and Power industries.
Lift Plug valves as suitable for a variety of applications such as isolation, or switching where the medium is highly abrasive, or operating conditions are severe - such as very high temperatures.
SchuF produces a special range of lift plug valves for the coking industry - the IsoPlug and SwitchPlug range.
|
|
Whatever you want from a Bulk Materials cut-off valve you’ve got it with Clyde Materials unbeatable Dome Valve® - the cost effective valve solution.
The Clyde Dome Valve®, widely regarded as the original and best material handling valve in the world, offers exceptional life from only a single moving part. The Dome Valve® is recognised as a low maintenance, long life solution that can last at least 1 million cycles between maintenance inspections. It has the ability to cut through static or moving columns of material and is pressure-tight, ensuring a consistent pressure tight seal is created when the valve is in the closed position, but in the open position it provides an unrestricted full bore opening for the best product flow characteristics possible. The Dome Valve® can also be used as a line, vessel or reactor isolation valve.
The Dome Valve® enhances other technologies from Clyde Materials Handling, a leading provider of pneumatic injection, conveying, materials handling & vacuum cleaning solutions.
The solutions we create for our customers generate many benefits and are backed by three decades of domain knowledge, expertise and a track record of generating exemplary success.
Dome Valve® sold in the United States under the trade name ‘Spheri Valve’
|
|
Rising-plug style valve for process instrumentation applications. Provides users with a highly reliable valve solution for applications where contaminated media can lead to premature valve failure.
The rising plug valve's ‘straight-through’ design supports higher flow rates than needle valves, helping to avoid the build-up of deposits.
The HRPV Series valve features an 8-turn actuation cycle, with a rolled spindle thread and smaller sealing area - lowering the torque required when controlling high pressure fluid flows and providing a long life. It’s rated to 10,000 PSI (689 bar) - a typical actuation torque of just 25 pound-inches (2.82 Nm) of torque is required.
Two types of body are available: inline 2-port design, and an inline design with a standard 3-port gauge interface at one end. In its smallest 1/4 inch female NPT version, the overall body length of the compact valve measures just 60.5 mm.
As standard, the valve is provided with PEEK seats, which allows the valve to operate up to 200+ degrees C, and resists wear and damage from the kind of aggressive media encountered in oil and gas processing environments.
Fabricated from 316 stainless steel as standard, HRPV Series valves can optionally be specified in a wide range of exotic alloys.
|
|
HILCO Transfer Valves assure positive sealing for uninterrupted flow and a low pressure drop. They feature an innovative spring loaded pad and shaft design with large cross-section O-ring seals. Top and bottom covers with centering pilots provide support to the body to resist deformation from pipe strain. The turning mechanism features a choice of handle, wormgear or actuator designs to meet your requirements.
Built to Hilliard's exacting standards, these transfer valves allow for replacement of the pads without replacement of the entire valve. Six standard sizes are available (1-1/2" to 8"), as well as a split transfer valve model designed for duplex coolers.
Continuous flow transfer valves are available in carbon steel, 304, and 316 stainless steel. “B” design, and “D” (zero leakage) design valves are available in polymer-coated stainless steel.
HILCO also manufactures 3-way valves coupled together with a common actuator and handle for duplex cooler applications. This helps to minimize extensive piping runs previously required while at the same time, reducing overall costs.
|
|
|
Design V150 is a single flange valve for throttling or on-off operation for many different applications in the process industries. The V150 is available in NPS 1 through 20, CL150 (DN 25 through 300, PN 10/16). Trim components are interchangeable between Design V150, V200 and V300.
|
|
|
|
