|
|
TRIFLUX series is available both with L and T bore and allows to divert the flow in all directions including the inlet shut off, applicable to each of the three threaded ends. It is suggested for gas and water distribution, industrial and civil heating, water plants at medium pressure, hydraulics and pneumatic, non aggressive media and vacuum.
|
|
Flow Patterns:
Hayward Manual Three-Way Ball Valves come standard with a two port "TW" ball allowing for three flow configurations within 180 degrees of rotation. With the bottom port as the inlet, the flow can be directed out the left port, out the right port or shut off. Hayward Actuated Three-Way Ball Valves come standard with a three port "NT" ball allowing for two flow configurations within 90 degrees of rotation. With the bottom port as the inlet, the flow can be directed out the left port or out the right port, there is no shut off position. A "TW" ball, used with with the proper electric actuator, adds what is typically called a "center off position" to the "NT" flow pattern of actuated valves. An optional "TP" ball, used with either manual or actuated valves, allows flow through all ports at the same time or flow shutoff.
True Union Design:
This makes these valves very easy to maintain by allowing for easy removal from a piping system without breaking down the piping connections. Just unscrew the three assembly nuts and lift the valve body out of the line.
Easy to Actuate:
A manual valve can be easily automated. Just remove the handle and install the optional actuator mounting kit. The mounting saddle is integrally molded into the valve body. For rock-solid actuator mounting, the valve incorporates a unique design whereby the mounting bracket mounts directly to the valve body. This assures proper alignment of the actuator to the valve without creating any damaging side loads to cause premature stem seal failure.
No Metal, No Corrosion:
Hayward all plastic three-way valves contain no metal parts. The valves will never fail because of corrosion and they do not require painting or epoxy coating to stand up to aggressive environments. |
|
Ball valves
Stainless steel range, for industry
Manual ball valves, in S.S316, with padlocking handle :
- One piece body valve with female/female ends (threaded BSP), nominal size 1/4" to 2"
- 2 parts body valve with female/female ends (threaded BSP or NPT) 1/4" to 3"
- 2 parts body valve with male/female ends (BSP), 1/4" to 2"
- 2 parts body valve with male/male ends (threaded BSP), 1/4" to 2"
- 3 parts body valve with female/female ends (threaded BSP), 1/4" to 4",
with or without ISO mounting socket
- 3 parts body valve to be welded (Socket or Butt welding) 1/4" to 4",
with or without ISO mounting socket
- between flanges ball valve 10/16 bars, 1/2" to 4"
- 2 parts ball valve with flanged end, 1/2" to 4"
- 3 parts ball valve with flanged end, 1" to 4"
- 3 way - threaded end ball valve (BSP) nominal size 1/4" to 2", with ISO mounting socket
- 3 way - flanged end ball valve 10/16 nominal size 1/4" to 2", with ISO mounting socket
Motorised ball valves :
- With pneumatic actuator
- with electric actuator
- many possible options
We also have a "brass" range of ball valves for home, industrial, or gas use... |
|
Automated Ball Valve - Series BV2
Full Port, Stainless Steel Construction, Rated 1000 psig (WOG), Electric and Pneumatic Actuators
Automated Ball Valve - Two-Way Plastic - Series PBV
PVC or CPVC Construction, Electric and Pneumatic Actuators
Automated Ball Valve - Three-Way Plastic - Series 3PBV
PVC or CPVC Construction, Electric and Pneumatic Actuators
Two-Piece Ball Valve - Series BV2M
Full Port, Stainless Steel Construction, Rated 1000 psig (WOG), Actuator Mounting Pad
Two-Piece Ball Valve - Series BV2MB
Full Port, Economical, Rated 600 psi (WOG), Blowout-Proof Stem
Three-Piece Sanitary Ball Valve - Series BV3HL
Hand Lever, SS Construction, Cavity filled
Three-Piece Sanitary Ball Valve - Series BV3HL-3A
Hand Lever, Cavity filled, Meets 3A Sanitary Standards
True Union Ball Valves - Series TBV
PVC Construction, Full Port, Economical
|
|
The TOTAL ball valve, with full bore, is an extremely robust product with perfect air bubble sealing
does not need any maintenance, is equipped with wrapping seats ensuring long life cycles. The patented outside sealing system guarantees the maximum reliability during the time.
The valve is approved according the DIN-DVGW standards: such approval was obtained for the first time in 1974 and then always renewed up to the present one. All valves are tested at 25 bar pressure, for a period longer than 48 hours.
|
|
Ball valves
DN 6 – 100; valve bodies in PVC-U, PP, PVDF (pressure 0 – 10 bar; operating temperature -10 to 80°C), stainless steel (pressure 0 – 60 bar; operating temperature -20 to 600°C), body versions: straight through body (2/2-way valve), T-valve (3/2-way valve); seal materials in FPM, EPDM, PTFE; connections: threaded socket, solvent cement socket, butt weld spigot, flange; manual, pneumatic and motorized operators
|
|
-Diameters from d32-d225
-From d63 with two-steps planetary gear
-Low maintenance
-Long life cycle
-Operating pressure of body 24 bar (testing pressure 36 bar)
-Pressure-resistant and rigid housing without welds
-No change of cross-section and reduction of flow
-Optimum flow design (cavitations, flow noise)
-Free passage for scraping
-Profiled seals rinse-proof in open and closed position
-Protection system prevents introduction of soiling and deposits
-Resistance against corrosion
-Higher elastic capacity than e.g. steel
-No cavitations / dead space
-Major energy saving in water supply
|
|
| Cam-Tite ball valves are engineered to provide the very best performance for demanding hazardous and corrosive applications. Designed to overcome such inherent valve problems as high operating torque and stem leakage, Cam-Tite ball valves feature a unique, non-spherical ball with a bevel at the lip of the port. This configuration minimizes pressure on the seating areas, thus reducing cold flow and prolonging seat life. |
|
| for corrosive and high-purity fluids in chemical, pharmaceutical, semiconductor and industrial application, manual or automated, ISO + ASME/ANSI, up to 200°C (400°F) |
|
1-Piece, Instrumentation, 40 Series Ball Valves
1-Piece, Instrumentation, 40G Series Ball Valves
2-Piece, Instrumentation 33 Series Ball Valves
3-Piece, Alternative Fuel Service, High Pressure (up to 6000 psig [413 bar])
3-Piece, Instrumentation, High-Pressure (up to 10 000 psig [689 bar]), 83 Series Ball Valves
3-Piece, Multipurpose SK Series Ball Valves
3-Piece, Process / Instrumentation, 60 Series Ball Valves |
|
Two-way and three-way ball valves which can be handled both by hand or through pneumatic and electric actuators.
Pressure interval: 50 bar / 210 bar
Temperature interval: -20ºC / 200ºC
Connections: from 1/4" to 3"
Made in several alloys.
|
|
Series 77 Ball Valves feature a high quality 316L investment casting. They are available with sanitary clamp or orbital tube OD ends. Select the cavity filled or non-cavity filled design. Superior leak protection is accomplished by using a patented live-loaded packing system featuring Bellville washers and double "V" ring packing. An ISO 5211 mounting pad is provided for easy automation.
Direct Mount, easy to automate
Sizes 1/2'' to 4"
Cavity filled and non-cavity filled
ISO 5211 Mounting Pad
800/1000 PSI
316L Body Ball and Stem Full Port
Sanitary clamp ends or extended tube OD ends
Excellent for Pharmaceutical and food & beverage
Main valve components are made from 316L stainless steel
Body, and ends are 316L CF3M ASTM A-351 investment cast stainless steel
Ball is machined from 316L CF3M ASTMA-351 cast stainless steel
Stem is machined from ASTM A-493 316L bar stock
Full traceability on all wetted parts (MTR's)
Standard internal polish is 15 Ra and is polished to meet ASME BPE specification DT-12 and Table SF-6 as required.
Standard seats TFM (FDA, USP 23 Class VI) TFM (TFM is a trademark of Dyneon)
Stem packing TFM
Full port to I.D. of tubing for reduced pressured drop
Bottom entry 316L pyramidal live loaded blow out proof high cycle stem adjusts to temperature and pressure fluctuation Locked stem nut to prevent loosening after continuous valve actuation
Dual anti-static devices on stem (contact between stem and ball, and stem and valve body)
ISO 5211 direct mounting pad
Direct mount actuation 1/2" to 4"
Handle locking device when manually actuated
3-piece body construction for ease of repair
Open bolt design to facilitate full external cleanability
Clamp, extended butt weld, or clamp by extended butt weld.
Clamp end requirements per ASME BPE 2002 DT-10, per table DT-2
Extended butt weld- 316L CF3M ASTM A-351 controlled chemical composition to ASME BPE 2002 table DT-3 and dimensionally per ASME BPE 2002 table DT-4 and DT-5
Please download our brochure for more sizes & tech specs. |
|
| You can count on Conbraco for top quality Apollo® bronze and steel ball valves in all sizes and shapes, and with all the connections and options you need. Whether you need valves for hydronic systems, irrigation, instrumentation, or tough industrial process flow, one of our ball valves is sure to fit your purpose. We have Two Piece, Three Piece, Unibody, Flanged, Three-Way, Union End, Steam Prep, Specialty, Top Entry and Barstock valves for every need you can possibly imagine. Apollo® ball valves deliver world-class performance for a universe of applications. |
|
Spirax Sarco ball valves offer safe and effective shut-off and control for steam, liquids and gases.
Our comprehensive range offers a choice of body design, materials, connections, seals and options, specialty valves suitable for specific applications and fluids, firesafe and actuated valves.
The range incorporates single, two and three piece valves in sizes up to DN150. |
|
| J+J, a UK ISO9001:2000 quality assured valve actuation specialist company, offer a wide range of ball valves fitted with the J3 reversible IP65 multi-voltage electric actuators. Valves offered are brass ball valves, stainless steel ball valves, cast iron ball valves and plastic ball valves. Most are availalble in 2 port and 3 port design. All packages are assembled & tested in-house. |
|
The ANTARES split body ball valve, with full bore, is used as an ON-OFF valve for: chemical products, food, installations for gas, water, air distribution. Suitable for vacuum, steam up to +195° C with PTFE+CARBOGRAPHITE. Thanks to its firm standardizations it is among the most used valves in all industrial plants.
|
|
| Rotary plug valves suitable to control high flow rates with high rangeability. The triple eccentric seat/plug design guarantees zero leakage and low initial breakaway torques when opening and closing. |
|
Temperature Control Valve - Series 36R
Self-Contained Valve/Actuator/Sealed Thermal System in One Compact Unit, Direct-Acting/Reverse-Acting
Control Valve - Series Hi-Flow
Linear Characteristics, 1/2" to 4" Sizes, 2-way or 3-way
Pneumatic Pilot Valve - Series 2V
2-way or 3-way, Ideal for Air/Water/Gas/Steam Service, Bronze Body |
|
Two Proportional Flow Control Rates with One Valve: Hayward ProFile2 corrosion resistant, proportional control ball valves provide two linear flow curves; one for fast opening and one for slow opening. The percentage of flow through the valves with either flow curve is equal to the degree of opening. As the valves are opened or closed, the flow varies in direct proportion to the valve opening. This permits predictable, accurate control of the downstream flow rate with a 1/4 turn valve.
Unique Design "Characterized" Ball: These valves utilize a unique, patented ball with a special "characterized" opening that results in the linear flow rate change. Valves are shipped with the ball installed so that the smaller opening enters the flow first, creating the slow open rate. To switch to the fast opening rate, simply reverse the ball in the valve. With the larger opening first, the flow starts fast with slower, more controlled changes as the ball is turned to "full open".
Perfect With Positioners: Hayward ProFile2 Proportional Control True Union Ball Valves can be supplied with optional electric or pneumatic actuators with positioners for automated modulating service applications.
Never a Problem with Corrosion: Because of their all plastic construction, Hayward ProFile2 ball valves will never rust or corrode. They can survive corrosive environments and harsh weather conditions without the need for painting or expensive epoxy coatings.
|
|
The ISIS ball valve, with full bore, is a product particulary suitable for ensuring a high working reliability at medium pressure in water installations. It is certified by BRITISH GAS and by WATER RESEARCH CENTRE.Blow-out proof system, with perfect air bubble sealing, does not need any maintenance, is equipped with wrapping seats ensuring long life cycles.
An antifriction ring forms the first automatic sealing at high pressure.
Two self-adjusting cone-shaped seals, with PTFE-PTFE sliding, therefore without wear, form the second sealing at low pressue.
1 O-Ring in NBR for sealing at low pressure and vacuum.
All valves are tested at 25 bar pressure, for a period longer than 48 hours.
|
|
The TITAN 3-piece ball valve, with full bore, is used as an ON-OFF valve for: chemical, water and pneumatic plants, for installations with high interchangeability of components and for steam up to 10 bar. The valves are designed and manufactured in order to allow inspections and maintenances on line by extracting only the body.
|
|
The VENUS ball valve, with full bore, guarantees a high working reliability at low pressure in gas installations: is certified DIN DVGW by the German gas institute, and BRITISH GAS by the British gas institute.
Blow-out proof system, with perfect air bubble sealing, does not need any maintenance. The patented outside sealing system guarantees the maximum reliability during the time.
1 O-Ring in NBR for sealing at low pressure and vacuum.
All valves are tested at 25 bar pressure, for a period longer than 48 hours.
|
|
| Autoclave's high-pressure ball valves have been designed to provide superior quality for maximum performance within a variety of valve styles, sizes, and process connections for pressures to 20,000 psi. Our unique design innovations include an integral one-piece trunnion mounted ball and stem that eliminates the shear failure common in two piece designs, re-torqueable seat glands that result in longer seat life, and lower friction stem seal that reduces actuation torque and enhances cycle life. |
|
The ALBA 2-piece ball valve, with full bore, is used as an ON-OFF valve for: chemical products, for water and pneumatic installations, gas, water, vacuum. For steam within limited working conditions and with special seats. All parts have to be adequately degreased if the valve have to be used for oxygen.
Temperature: For fluids from -20°C a +150°C
Pressure: For fluids from 100 bar to 40 bar |
|
High Pressure Stop Valve, forged Form with
screwed bonnet and internal stem thread
universal applications.
Typ : AVD, AVI |
|
The GHILUX ball valves are shutoff valves type ON-OFF. The opening and closing functions are made by hand, acting on the control spindle of the ball with the handle, or operated with a spanner or screwdriver.
The main characteristics of these valves are the different versions and the reduced dimensions, which have been carefully studied
British Gas approved
The ball valves are available in the following sizes:
tube from 6 up to 18;
thread of 1/8 to 3/4.
|
|
The J+J electric actuator is widely used in the plastic valve market because it has a plastic housing making it light in weight, and as it has more standard features than any of its rivals, offers exceptional value.
The new J3 Series electric actuators offer an LED status light and plug & play conversion kits that change the function from on-off to failsafe, or modulating, or both. |
|
| Cam-Line plastic-lined trunnion ball valves offer the same proven design benefits as the Cam-Tite product line, including tight shut-off, reliable stem sealing, and unsurpassed torque reduction—all unique features in a plastic-lined ball valve design. With special Tefzel or polypropylene linings and option PVDF coatings, Cam-Line ball valves are well suited for highly corrosive applications within the chemical processing industry such as sulfuric and hydrochloric acid. |
|
Rugged, Compact Design:
Hayward's rugged, low cost QIC2 all plastic PVC ball valves incorporate many design features found only on higher cost ball valves. Features such as PTFE seats, full porting and a 150 PSI pressure rating are all standard on every size of QIC2 ball valves.
Cost Sensitive Applications:
The QIC2 ball valve is perfect for OEM and other applications that require a reliable ball valve at an economical price. The QIC2 valve has been designed and tested to make certain it will perform year in and year out in the most demanding applications without leakage or failure. The internal components of the QIC2 ball valve are completely encapsulated inside the one piece valve body which means that the valve never requires adjustment. The QIC2 valve is ready to be put into service right out of the box.
Lightweight and Compact:
QIC2 lowcost ball valves are designed to fit into spaces too small for other valves. They are about 1/3 the overall size of a true union ball valve and they weigh an average of 50% less. This makes them ideal for skid mounted and other applications where space and weight are critical considerations.
Can't Rust, Won't Corrode:
Their all plastic construction means that they will never fail, stick, or jam because of rusted or corroded parts. And they'll work in places and environments where metal valves must be painted or coated just to survive. |
|
-Diameters from d32-d225
-From d63 with two-steps planetary gear
-Low maintenance
-Long life cycle
-Operating pressure of body 24 bar (testing pressure 36 bar)
-Pressure-resistant and rigid housing without welds
-No change of cross-section and reduction of flow
-Optimum flow design (cavitations, flow noise)
-Free passage for scraping
-Profiled seals rinse-proof in open and closed position
-Protection system prevents introduction of soiling and deposits
-Resistance against corrosion
-Higher elastic capacity than e.g. steel
-No cavitations / dead space
-Major energy saving in water supply
|
|
|
|
