|
|
- 2 sizes
- E 6 - 72 from 8 to 97 kg/h in 12 performance ranges
- E 100 from 135 to 160 kg/h in 2 performance ranges
with working overpressures from 6 to 12 bar.
- Also available as pure steam generator made of stainless
steel.
- Can be equipped with fully automatic operation including
automatic blowdown, desalination and automatic control
by timer, remote control or central building control systems.
- Availabe as a compact, ready-to-operate unit with water
treatment and waste water cooling.
- No boiler house needed. In many countries, CERTUSS
electric steam generators can be installed without permit.
|
|
|
|
|
|
Uni-Matic series flash coil steam generators are suitable when quick steam production is needed, also in case of frequent start and stop (Steam is instantaneously produced and there is not an accumulator).When steam is requested, production should be almost uniform, without heavy peaks.
Benefits:
- Easy operation, reduced maintenance and well proven performance.
- Tubular structure of both combustion chamber and convective section can be easily removed for inspection and replacement.
- Reduced operating expenses thanks to the high std boiler efficiency (88%).
- Flexibility in operation thanks to the quick steam production, even in case of frequent burner start and stop.
- Low thermal losses because there is no steam accumulator.
- Thanks to the restrict thermal inertia, UNI-MATIC are suitable to be used both in continuous and batch operation.
- High operating safety margin, thanks to the limited water volume running in the entire coil.
Fields of application:
- Laundries
- Dyeing process, laboratories, ironing factories
- Foodstuff and bottling processes
- Rubber, polymer and synthetic processes
- Community
- Desalination plant
- Chemical & petrochemical processes
- Agriculture processes
- Auxiliary services
|
|
|
|
|
|
- 8 sizes with 16 performance classes ranging from 80 to
1800 kg/h of saturated steam with operating pressures
up to 32 bar.
- Unit with integrated fan burners for natural gas, liquid gas,
fuel extra light, and, as of 500 kg/h of saturated steam, with
combined burner natural gas/fuel EL. Biogas burners are
possible as well, depending on the gas quality.
- Availabe with fully automatic operation including automatic
blowdown, desalination and automati ccontrol by timer,
remote control or central building control systems.
Automatic sequence control or on-off control regulated by
the mains pressure for installations with multiple boilers.
- Facilitated installation conditions in many countries. No boiler
house required.
- Electronic function indication system with clear text indication
and long-time storage allows to analyse operation and
performance over a long period.
- Potential-free contacts allow to transmit up to 20 different
function messages to a central building control system.
- High degree of efficiency due to a proper burner technology,
perfectly adapted to the special construction of the steam generator.
Possibility to install a downstream flue gas heat exchanger.
|
|
|
|
|
|
Type: Model 200-Model 8000
Capacity: 200kg / h-8000kg / h
4 bar-20 bar
Work with gas, light oil, heavy oil
Boiler efficiency: 90%
Burning efficiency: 91-92%
3 pass special design
Delivered with followings
Electric panel
Economizer
Burner
Feedig pumps
Condensing tank
Water softner
ADVANTAGES OF BROX STEAM GENERATORS:
Brox steam generators can achieve steam in 5 minutes in the desired level. It does not need to be run before usage.
The steam is produced in the antigorite. Like classic boilers, it does not have the high pressure blow up risk.
It does not have any water level instruments. Because the system is controlled automatically, nobody needs to be present.
It is produced vertically and horizantal depending on your request.
It is designed to give steam in the shortest time, to save time and energy, and to provide maximum safety for the industries in need.
With the design and fast firing capability, it will reduce the consumption to minumum. When compared with classic boiler, it saves 10% more.
It is designed to fire naturalgas, diesel fuel and fuel oil. It can use all three with the same firing unit.
To get quality system, enough water is given to the chamber with the same ratio of fuel that is needed for firing. In big units, the fuel and water ratio is designed in modulations.
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY
|
|
- Completely pre-installed, ready-to-use, on a zinc-plated,
coated chassis including feed water tank and blowdown receiver
for wastewater. Electrical distribution with all switching elements
in central switch cabinet.
- Alternatively available as steam accumulator or heated with steam,
hot water or thermo-oil.
- Outputs ranging from 80 – 2000 kg / h with steam pressures from 0.5 – 25 bar.
|
|
|
|
|
|
BABCOCK WANSON are specialists in industrial coil boilers offering a range of steam generators from 150 to 8000 Kg/h with operational pressures from 5 to 50 bar. The water volume is low and flows directly proportional to the desired steam output using a positive displacement water feed pump. In the high pressure HPVAP Series 100 bar is possible in a closed loop thermosyphon pumpless design offering very high overall plant efficiency without pressure vessels and suitable for a range of batch and variable process flow applications particularly in edible oil processing.
User advantages :
- reliability and robustness ;
- maximum safety due to the low water volume under pressure ;
- installation close to the process with reduced plant costs ;
- fast production of steam from cold start in as little as three minutes ;
- production of high pressure steam up to 50 bar, even 100 bar for the closed loops with thermosiphon application ;
- burner complies with the most stringent regulations and is perfectly adapted to the application ;
- compactness with small footprint and low weight ;
- low thermal losses with automatic blowdown and reduced losses from the casings ;
- well suited to intermittent operations ;
- quality of the dry steam with BABCOCK WANSON separator.
|
|
|
Tubeless steam generators VPR are the result of considerable experience acquired by Garioni Naval in costruction of traditional steam boiler. They are ideal for small and medium size plants where medium pressure (up to 10 bar) steam is required. Their particular tubeless design ensures standards of safety and realibility which have received considerable acclaim from our customers. Our tubeless steam generators are ideal for garment industries, dry cleaning, ironing shops, saunas, and all industrial processes where high reliability is required.
|
|
|
|
|
|
With its thousands of welds, pipes extending several hundred kilometers and many thousands of tons of heavy structural steel, the utility steam generator (boiler) is at the heart of any fossil-fired power plant. This is where the pulverized fuel is burnt at around 1,450 °C; forming here are also the hot flue gases and the extremely hot steam under high pressure, which subsequently drives the turbine blades.
HPE develops, designs and supplies steam generators for unit capacities up to and over 1,100 Mwe with 300 bar plus pressures, 600 °C live steam temperatures and reheater temperatures up to 620 °C for all the available fossil fuels. These extend from coal and lignite to specific fuels (e.g. gases from coke ovens / steelworks and refinery residues).
With a track record extending back over 100 years, Hitachi Power Europe is one of the market and technology leaders in utility steam generators. References include over 370,000 megawatts of installed power plant capacity (of which 180,000 MW is coal, 43,000 MW lignite and 140,000 MW oil and gas firing) which have been set up since 1970.
Developments are constantly ongoing in utility steam generators. New, highly-resistant materials, for instance, should enable them to achieve even higher steam temperatures and pressures. This is the way to raise the efficiency of tomorrow's coal power plants to over 50%
|
|
|
|
|
|
The MX range is a compact and affordable steam boiler ideal for small to medium sized users of process steam.
Each boiler is individually tailored to your specific needs and manufactured from start to finish in our own factory, thereby ensuring quality control of the very highest standard. All fittings are mounted in the factory to make installation on site as quick and easy as possible.
The boiler can incorporate any make of burner to suit a wide range of gaseous or liquid fuels in single, dual or tri-fuel combinations.
The MX boiler has a thermal efficiency in excess of 89% (based on NCV) .
External surfaces are well insulated and finished in tough, Aluzinc cladding.
The front door is lined with the latest ceramic fibre technology offering significantly less heat loss than traditional refractory materials.
The MX range has larger heating surfaces and steam space than comparable boilers, meaning desirable low heat transfer rates, Low NOX emissions, easily achievable outputs, and quality dry steam throughout the firing range.
A huge range of accessories are available to further enhance the boiler; contact us for more details.
Manufactured to BS2790 Class 1 with outputs to 3MW (5000 kg/hr) and operating pressures to 17 bar(g)
|
|
|
Clayton currently offers Steam Generators and Fluid Heaters in 17 sizes ranging from 25 to 1000 Boiler Horsepower (BHP) or 862 to 34,500 pounds of steam per hour. These units are controlled flow, water tube boilers, built to the appropriate national and local standards, using high quality materials and workmanship. Units are designed to burn natural gas, propane, light oil and heavy oil, as well as a combination of these fuels and are available with steam design pressures up to 3000 psig. Superheat Units, which provide superheated steam, are also available in a variety of sizes and for a range of steam pressures and temperatures.
|
|
|
|
|
|
Steam without restrictions
STEAM GENERATOR
Energy saving:
Production with a very high output of clean steam which can be used in the food industry.
Reduced statutory restrictions
3 ranges:
outside the EU Pressure Equipment Regulations ≤ 0.5 bar (110 °C)
categories of equipment Il and III (European PE Directive 97/23/EC) 3 and 4 bar (152 °C)
category IV
Optimised overall dimension:
Steam generators have a vertical or horizontal design depending on the power.
The reduced height enables installation in various locations (ceiling at 2.50 m)
An adapted power range
outside PED/low pressure, heat capacity from 120 to 1500 kW i.e. steam output from 170 to 2150 kg/h
categories Il and III, heat capacity from 120 to 800 kW i.e. steam output from 170 to 1150 kg/h
category IV: 120 to 800 kW
A patented innovative technology
which combines the benefits of an immersion heater with energy savings in gas energy.
Control by capacitance level probe
Stainless steel manufacture
which enables use within all types of environment: food industry, installation in community buildings and even outdoor installations.
Robust structure with reduced maintenance costs.
|
|
|
|
|
|
Clayton provides a line of Steam Generators to provide superheated steam. These units use the same proven design as the basic Steam Generator that produces saturated steam, but with the addition to the helical coil of an integral superheater section, in which the steam is superheated. The use of the integral superheater section eliminates the need for a separately fired superheater.
Units can be provided in a configuration that allows the user the option of providing saturated or superheated steam. Superheated steam can be provided at pressures up to 57 bar (850 PSIG) and at temperatures up to 343 ºC (650 ºF).
These units are available to provide superheated steam in a variety of applications – for industrial needs, as well as, as auxiliary boilers in power plants, and anywhere that superheated steam is needed.
Since superheater Steam Generators are essentially of the same design as saturated steam units, they provide the same advantages. The particular advantages as power plant auxiliary boilers include:
Rapid Start - from a cold state to full output in 5 to 20 minutes
The unit can be left in a cold stand-by condition
Fast Response to load swings
Compact Design
High Degree of Operator Safety – Non-Explosive Design
Low Maintenance – Single Burner
|
|
Heat Recovery Fire-Tube Steam Boilers
The gases heat recovery at high temperatures has a wide diversity of boiler designs, depending on the origin of the gases and on the heat transfer to the fluids needed for every process. The software developed in CERNEY permits the suitable application of the theoretical principles to the practice relating to boilers.
In our Heat Recovery Fire-Tube Steam Boilers range, the body of the boiler, formed by a cylindrical body of horizontal disposition, incorporates inwardly a multitubular bundle for heating transmission and an upper camera for formation and accumulation of steam. The gases circulation is carried out from a bridled front chamber up to the rear area, where it finishes its way in another chamber for fumes outlet.
|
|
Model ODP
SMOKE TUBE BOILER IN DRY BACK TWO-PASS DESIGN.
The boiler is supplied as a single-body, fully automated system:
- the multi-level or modulating burner and the stack can be supplied on request
General Features High performance and top quality steam are made possible thanks to the technical features of the boiler:
2 smoke passes
Big furnace for low specific thermal loads
Dry smoke inversion chamber
The tubes are expansion-fitted and welded
The furnace is equipped with omega reinforcements, also working as expansion joints
The tube plate is accessable through the front door
|
|
ALSTOM has extensive knowledge of steam generation, combustion, fuel technology and heat recovery systems
Our wide range of equipment includes:
-utility boilers including drum-type, advanced once-through (sub or supercritical) and fluid bed, with a complete range of firing systems
-heat recovery steam generators (HRSG) for large gas turbines (>50MW) in combined cycle or cogeneration applications
-boiler products, including air preheaters, mills and pulverizers
We cover all types of fuels oil and gas, bituminous coal, anthracite, lignite, petcoke, oil refinery waste, industrial by-products and biomass.
Products and supply tailored to meet our customers needs
|
|
|
DIGIMAG 380 is a MIG-MAG inverter welding equipment. Either air-cooled or water-cooled, it brings the flexibility to weld the widest range of industrial applications, meeting the requirements for both medium and heavy fabrication.
|
|
The SASL200 power source, more powerfull, has been designed to offer modularity for the customer who can add functions in accordance to his markets: AVC, Wire feeder, oscillation for.
The user interface has been improved through a color touch screen remote control, 5.7 inches (multi-language)
SPECIFICATIONS :
-Welding type: TIG
-Arcstrike: HF or contact
-Welding Current: 3 à 210 A
-Network:
Autoline, 110V-230V with PFC
-Pulse time: from 0,01 to 8 sec
-Power Factor : 160 A (100%)
-Memory: 200 programs/20 levels on Compact Flash card (per card)
-Weight: 23 Kg
-L x l x h: 530x500x400 mm
-Multi-language: english, french, german, spanish, italian, korean, japaneese and chineese, russian, turkish
-Thermic printer
-Compatible with all AXXAIR heads, SC and SAT and manual toches
|
|
Transportable microwelding equipment for surfacing tools on site (Whithout interruption of production, or dismantling of tools) such as:
- Plastic injection molds
- Cutting Tools
- Rubber Injection
- Extrusion
- Blowing
This device allows microwelding report of the material in small amounts through a variety of materials available in the form of powder, wire or ribbon (36 to 62 HRC).
|
|
Brushless alternating current welders (AC) and Brush Direct current welders (DC)
Insulation class: H
T.H.D. < 6%
Strike voltage: 45-60 V (AC) 65-85 (DC)
Usable electrodes: rutile, acid (AC) all types (DC)
Welding current: 130A to 220A (AC) 140-240 (DC)
Frequency: 50 o 60 Hz
Single Phase Generator (AC) Single Phase and Three Phase Generator (DC)
|
|
Every component in a Miller industrial engine drive is engineered and built to assure ultimate reliability in the most punishing conditions.
Trailblazer® 302 Air Pak™
Powerful all-in-one tool is designed for repair and construction with unbeatable multiprocess weld quality, integrated rotary screw air compressor, and 13,000 watts of generator power for job site tools.
Wildcat™ 200
Compact, lightweight, durable and cost effective machine is designed for the contractor and is great for maintenance/repair, farm and ranch applications.
Bobcat™
Economical welder/generator designed for rugged use. Mostly used for Stick, but also capable of Flux Cored, MIG and TIG. These units are great for farm, ranch, construction or as a stand-alone generator. New - fully enclosed case!
Trailblazer® DC
Designed for the professional welder who needs a welder/generator with excellent arc performance for all types of DC welding jobs.
|
|
|
|
|
|
MIG
Step-regulated industrial MiG/MAG
MIG is a range of robust, step-regulated, user-friendly and all-round machines for MIG/MAG dip-transfer or spray-transfer welding, from sheet metal and light structures to thick walls. Primarily develop-ed for mild steel but also applicable for stainless steel and aluminium.
MIG machines:
Many variants
There is always a MIG machine with high duty cycle for inten-sive quality welding day after day. Some models are supplied as C (compact) versions, others as STB versions (STB for separate wire-feed unit) and with option-al air-cooling or water-cooling.The many variants are designed based on the four primary models: MIG 305, 385, 445 and 545. The largest models feature four choke connections and up to 36 voltage steps.
The strong choke spool ensures fine ignition in dip-transfer welding and makes it possible to weld with solid or flux-cored wires in dimensions from 0.8 mm.MiG 385 STB MiG 445 STB MiG 545 STB 3 x 230 V/400 V 3 x 230 V/400 V 3 x 230 V/400 V 40-385 A A 40-445 A 40-545 A Energy-saving standby function for water pump/fan.MIG is supplied with several variants of both open and closed types of wire-feed units featuring four-spool drive and quick change of wires and spools. It is possible to use small or large wire spools or to feed wire from a drum.
|
|
|
|
|
|
PSM 708
The PSM 408, PSM 508 and PSM 708 models are synergic power sources with electronic technology. The dynamics of these systems have been carefully studied for MIG/MAG continuous wire welding on carbon steel, stainless steel and aluminium, in both Short-Arc and Spray-Arc mode.
The models PSM 408-508-708 are provided with complete functions for Mig/Mag welding in manual and synergic mode, and guarantee optimal welding dynamics. The SCR electronic technology with digital control provides accurate linear regulation of the welding current voltage, permitting easy parameter regulation even at a distance.
Optimal starts (Hot-Start Mig Soft-Start and Burn-Back) and above all safety and dependability in all operating conditions.
The SYNERGIC control panel with numerous programs stored, makes these power sources extremely simple to use and suitable also for non-expert personnel. The Auto-Setting device allows the power source to automatically compensate for mains voltage variations, maintaining welding arc stability. The current and arc voltage values are shown on the digital display and at switch-off the last welding condition is stored.
The synergy permits automatic optimal setting of all the parameters, with extreme simplicity. All you have to do is determine, according to the type of material/gas used and the wire thickness, the ideal program in the table of synergic curves and then set the value of one of the following parameters: material thickness, welding current, wire speed.
|
|
Champion™ 4500
Lightweight and compact,
the Champion™ 4500 welder/generator provides you with the power you need wherever and whenever you need it. As an AC welder, the Champion™ 4500 delivers up to 140 amps of welding power, making it an ideal choice for maintenance and repair projects. It's also an excellent source of auxiliary power, providing up to 4500 watts of AC power.
Champion™ Elite
the Champion™ Elite is ideal for farm, general construction, and emergency power applications. This unit is designed for Stick welding with quick and easy arc starts. It also performs general scratch-start DC TIG. The unit is capable of producing power while welding so your partner doesn’t have to wait to start on the next task. The Champion Elite offers a “no-nonsense” warranty. The engine is warranted separately by the engine manufacturer.
|
|
GLC 351/451/551-C
Fine power adjustment
Robust and modular design
Measuring devices:
For welding current and welding voltage
Wire burnback
Adjustable via potentiometer
Standby operation
For cooling pump and fan
|
|
Diesel-Powered Welder/Generators
These diesel-powered welder/generators feature smoother arc characteristics and more consistent, quality welds. Multiquip's simultaneous operation models range from 180 to 500 amps as welders and 3 to 14kW as generators.
|
|
|
|
|
|
The Ranger® 305 D is a powerful stick, TIG, and wire welding engine driven welder that is ready for all day, everyday performance on construction, maintenance or pipe applications. Rugged and dependable, the Ranger® 305 D is built with a totally enclosed case for maximum protection; Lincoln's Chopper Technology™ for an arc operators appreciate; and a 12 gallon fuel tank that will last you through the entire day. Lincoln's Ranger® 305 D ... it's ready for a workout.
Advantage Lincoln:
- Diesel Engine-Driven Welder
- A powerful 300 amp DC CC/CV diesel engine-driven welder. All rated outputs at 100% duty cycle 104°F (40°C).
- Multi-Process Welding
- Excellent DC multi-process welding for general purpose stick, downhill pipe (stick), TIG, cored-wire, MIG (CO2 and blended gas) and arc gouging.
- Digital Weld Meters
- Digital weld meters for amps and volts make it easy to precisely pre-set your procedures and monitor actual welding output.
- Superior Arc Performance
- Lincoln®'s Chopper Technology provides easy starts, a smooth arc, low spatter and excellent bead appearance.
- Plenty of AC Generator Power
- A portable powerhouse - delivers 10,000 watts peak (9,500 watts continuous) of 120V/240V AC generator power. Enough power to run lights, tools, and weld at the same time!
- AC generator voltage is constant at 120V or 240V at any weld dial setting.
- Skewed Rotor Design
- Skewed rotor design provides AC power waveshape suitable for operating Lincoln® Pro-Cut® plasma cutters and inverter power sources. Lincoln was first in the welding industry with this feature.
|
|
|
|
|
|
The Power Arc® 5500 is ideal for home, farm, contractors, maintenance, or business power outage emergencies. You get two great tools in one for double the value. First, you get 125 amps of AC welding output for many common maintenance, repair and construction projects. You also get maximum AC generator power in a lightweight package - that makes it easy to get auxiliary power where you need it - fast!
Advantage Lincoln
- 125 Amps AC Welding
- 125 amps AC welding output is ideal for 3/32" (2.4 mm) and 1/8" (3.2 mm) diameter electrodes.
- Single-range output control makes it easy to dial in the right welding setting for your application.
- 5500 Watts Surge AC Generator Power
- Sizable 5500 watts surge (4000 watts continuous) single phase AC generator power keeps your lights, tools, heaters, sump pumps or appliances running during emergencies or for any project - any time, anywhere!
- Circuit breakers provide secure overload protection for the generator and your tools.
- Rugged Tube Frame
- Rugged tube frame roll cage adds protection and many lift handle points.
- Easily Transported
- Two people can easily transport the Power Arc® 5500 where auxiliary power is needed - fast!
- Lightweight - up to 75 lbs. (34.0 kg) less than many competitors!
|
|
The AC-225C is a stick welding power source with continuous output control from 40-225 amps. The AC-225C produces an extremely smooth welding arc, at any amperage setting, for most welding application. The AC-225C can be used for a variety of materials including carbon, low alloy and stainless steels, from 16 gauge sheet metal to heavy plate.
Applications include: maintenance repairs, fabricating or modifying equipment, building tools or fixtures, rebuilding worn parts or dies, and hardfacing new or worn parts for longer service life. Also used to repair or fabricate cast iron parts.
|
|
Welders from 170 to 220A with mechanical regulation of the welding current. Reliability, sturdiness. Soundproof and open versions depending on each particular need.
PRAMAC WP 230
Item code: LC220MRA000
Rated maximum power (LTP) : 5,7 kW
Rated prime power (PRP) : 5,5 kW
Voltage : 230, 400 V
Frequency : 50 Hz
Minimum welding current : 30 A
Maximum welding current (35%) : 220 A
Max. diameter of rutilic electrodes : 5,00 mm
Max. diameter of basic electrodes : 4,00 mm
Max. diameter of cellulosic electrodes : 5,00 mm
Engine manufacturer : Ruggerini
Starting system : Electric
Speed governor : Mechanical
|
|
|
|
see the results for the following category : 
