|
|
Dura-Sleeve return idlers are a patented abrasion resistant urethane sleeve that is easily clamped on any existing or new rubber or urethane disc return idler shaft.
* Patented Design - of our idler sleeve clamping system utilizes you to replace worn out rubber or other urethane disc return idlers.
* Abrasion Resistant Urethane - compounds provide wear ability that exceeds 5 times the wear life of standard rubber disc return idlers.
* Meets all CEMA Standards - and available in any belt width and inside and outside roller diameter.
|
|
| ... products without technical information |
| |
The Tru-Trainer employs a unique and highly effective tracking action, which is non-damaging to the belt and reacts immediately if the belt begins to drift off center.
Because it does not rely on contact with the belt edge in order to guide the belt, belt edge damage, which occurs frequently with other tracking systems, is avoided. The center pivot is unique and simple, consisting of a stainless steel pin within a solid steel center shaft. Advantages include:
- Simple to Install
- Maintenance Free
- Operates In All Conditions
- Increases Conveyor Belt Life
- Reduces Spillage and Waste
- Minimum Working Parts
- Lower Motor Power Consumption
- Operates on Reversible Belts
- Rubber Covered for Better Traction
|
|
|
|
|
|
MARTIN® TRAC-MOUNT™ Idler
MARTIN® TRAC-MOUNT™ Idler uses sliding frames to fit into tight spaces between cradles, ensuring proper rolling support for the belt.
Simple Service
Individual rollers slide in and lock in place from outside the belt. No more laying idler sets on their side.
Proper Conveyor Belt Support In Tight Spaces
Slide-in frames need only 8 inches (203 mm) of width for 6-inch (152 mm) rollers.
Meets CEMA Standards
Available for any belt width or troughing angle, with any brand of rollers.
MARTIN® Transfer Points are custom-engineered by Martin Engineering to eliminate blockages, reduce impact, centralize loading and guarantee the material flow rate.
Martin Engineering makes bulk materials handling cleaner, safer and more productive, with engineered systems including conveyor belt cleaners, conveyor load zone/transfer point chutes, impact cradles and slider beds, skirtboard sealing systems, air-supported belt conveyors, air cannons, pneumatic (air) and electric industrial/bin/railcar/truck vibrators, belt training/alignment devices, dust suppression/collection/control systems, and specialized contract services including installation/maintenance and silo/bin/bunker cleaning.
|
|
Tracker Rollers from HOSCH ensure conveyor belt alignment.
- Maintenance free
- No wearing parts
- Durable rubber surface
- Suitable for all environmental conditions
- Minimum space required, compact dimensions
- Ease of installation
- Minimum of installation
- Also suitable for reversing operation, ideal for retrofitting
|
|
The Chevron secondary belt cleaner uses the speed and force of the belt rolling over our patented rubber disks. The unique rotary fingers are forced against the base of the chevrons to dislodge material from the belt.
- Sweeping Action - of each disk cleans in front of and behind each and every chevron.
- Easy Maintenance - no motors, air nozzles, or other problematic equipment to maintain.
- Works Great - in the pulp and paper, fertilizer, potash, and other bulk material industries where chevron style belts are heavily used.
- Solid or Notched - 8” (200mm) diameter abrasion resistant rubber disks are available depending on the height of the chevrons and the conveyor belt speed.
|
|
|
Flexco Chevron Belt Cleaner takes a new approach to cleaning chevron, cleated, and raised rib belts. Hundreds of rubber fingers create a rotary cleaning action that easily flicks carryback off the belt. And without the typical clogging and rapid wear problems associated with brush-type cleaners. Now there is a better solution for wet sand belts, wood chip belts and other raised top or grooved belts.
|
|
|
Our brushing machine type BM 1138 has been constructed previously for heavy-duty conveyor belt cleaning in coal mines and foundries. Today we supply it for almost all kinds of industry where conveyor belts have to be cleaned.
|
|
|
|
|
|
MARTIN® Brush Belt Cleaners are specially suited for the removal of fines and residue from ribbed, flighted, grooved, or chevron belts. Versions are available to suit your conditions and your budget.
Motor-Driven Cleaning Action
One or two-horsepower motor (depending on belt width) turns brush against belt motion.
Match Cleaner To Requirements
Specify the cleaning system to suit your conditions and your budget.
MARTIN® Standard Brush Cleaner
MARTIN® Standard (Spiral) Brush Cleaner is value-priced answer to belt cleaning problems.
MARTIN® Strip Brush Cleaner
Uses 12 brush strips to form cleaner that sheds even moist material that would plug other brushes.
Brushes To Fit Need
MARTIN® Standard (Spiral) Brush Cleaner uses 0.38 inch (0.96 mm) polypropylene bristles wrapped in spiral around the hub. MARTIN® Strip Brush Cleaner forms brush from strips with 0.40 inch (1 mm) polypropylene bristles. Other materials and bristle diameters are available.
Martin Engineering is the world’s leading developer and manufacturer of engineered conveyor belt cleaning systems. In this position, Martin Engineering has developed fundamental principles of cleaner design that have set standards for belt cleaner engineering and performance.
The multiple-cleaner system originally adopted by Martin Engineering is now the standard for applications on belt conveyors carrying all types of bulk materials around the world. End users (and other cleaner manufacturers) have accepted it almost universally.
|
|
|
|
see the results for the following category : 
