|
|
On target for each production process is to achieve the highest possible net product and to guarantee the defined quality of the product.
There are several reasons for reducing a product:
-after sack dipping station
-after dryer
-fried product
-recycling process
-enlargement of surface of product
-grinding process
-and further more
When choosing the right delumper, the efficiency of a production process can be significantly increased and production cost can be reduced.
Proof it by trying our test units!
|
|
The CRUSHER is installed at the extraction point of silos, hoppers, containers and allows the crushing of bulk or powder products which have been accumulated after a long storage period.
The CRUSHER enables these products to flow more easily. It is available in 3 versions : steel, stainless, aluminium.
|
|
Desagglomeration of powder blocs according to GMP standard.
Developped for the desagglomeration of powder blocs, the JetBreacker reduces the powder blocs to particles smaller than 10 mm.
Main advantages :
- GMP execution with CIP option
- Compact and mobile execution with bag discharge optionally
- Possibility to be connected to the loading station (silo or Big Bag)
- « High contained » solution up to OEB5
- High desagglomeration efficiency
- Excellent quality and price ration
- More than 15 systems in operation at customers side
|
|
Application
Desintegration of product agglomerates, lumps,...
Example:
* lumps formed in a silo
* filter cakes in front of a pneumatic conveyor
Working Principle
Product falls in the delumper. The lumps are hit by the rotor knives and forced through a grid. The fines pass straight through the grid.
|
|
Tuffer Aerator/Lump Breaker Series 329
The Tuffer aerator/lump breaker effectively reduces moist, semi-moist or dry solids down to grain size. The counter-rotation of the fast moving blades helps to reduce lumps with ease and aerates the material.
The result is a more consistent particle size and a fluffier bulk solid. Material will gravity feed and flow easier, improving overall handling efficiency.
Features:
Abrasion-resistant blades
Air purge shaft seals
Rugged construction
V-Belt drive
Low profile design
Self-cleaning
Low cost
|
|
The lump breaker is set up in a vertical product flow chute. Its main components are a frame, a fixed grid and rotating blades.
It will break up any lumps and detect any solid foreign substances inside the flow.
This material is typically used after a storage silo and before a pneumatic conveying system ie airlift, airslide, etc...
|
|
Clod-crusher E600 knife
Crush and désagglomère the matters taken masses some or compressed.
Electra: INDUSTRIAL materials of crushing, mixes, handling, storage, proportioning, sifting and bagging
|
|
| ... products without technical information |
| |
The firms BKM Bolender Maschinenkonstruktion GmbH and
Gerd Wolff Maschinenfabrik GmbH (Hagen-Germany)
Spezialists in strip mills and special machines for the steel fabrication.
Our product offering ranges from simple models to highly sophisticated designs: for rolling, cut-to-length line, conveying coils, bundles and strip material of hot wide strip, medium strip, cold roll machine, distal steel sheet, slit strip, electric strip
*Rolling mill
*Strip mill
*Mill stands for cold rolling
*cut-to-length line
*High performance slitting line
*Pickling and tempering lines
*Traversing spoolers
*Packaging lines
*Coiling lines
Compact slitting lines
Equipment for cold rolling mills and Service-Center:
We have - or develop - the right components and equipment for any task, for example:
*Straightening machines
*Hydraulic shears
*Annealing hoods
*C-hooks
*Conveyor racks
*Coil decoupler
*Coil tilting fixture
*Coil tumbler
*Reel
*Decoiler
Service & Maintenance:
*Inspection
*Repair
*Training
|
|
We design and produce gearboxes and machines for the steel and non ferrous metals industry:
- gearboxes for roll stands
- shears
|
|
BWG supplies strip processing lines for the steel, stainless steel and aluminum industries.
We cover a strip thickness range from approx. 0.05 mm through 16 mm, strip width up to approx. 2,300 mm and process speeds up to and over 600 m/min. Our strip processing lines are renowned in the industry for their innovative solutions with outstanding process results, their high uptime availability in conjunction with a high level of automation, robustness and maintenance-friendliness.
|
|
| ... products without technical information |
| |
|
|
|
|
FEATURES
LIFETIME Guarantee:
HFT offer a lifetime guarantee on the MOTOR of the TEG-3
Repeatable points every time:
The use of the 'TEG - 3 Tungsten Electrode Grinder' will give exactly the same tungsten points every time, enabling consistent repeatable arc performance and welding results.
Axial grinding:
By grinding the points longitudinally, the 'TEG - 3 Tungsten Electrode Grinder' eliminates arc flicker or wander.
Sizes:
Sizes from 1.6mm to 4mm can be ground as standard. Any other sizes can be catered for on request.
The TEG-3 Grinder is so powerful that it will grind tungsten electrodes up to 6 mm diameter, without stalling or burning out the motor. Remember, our lifetime guarantee and it has no limits. With the aid of a special collet accessory, short tungsten electrode lengths can be held, thus increasing the life of each electrode.
Low cost:
The TEG-3 Tungsten Electrode Grinder, has been designed and manufactured specifically for grinding Tungsten Welding Electrodes up to 6 mm diameter.
Prolonged tungsten life:
A tungsten electrode tip ground with the TEG-3 machine, will have a much greater life than a tip that has be hand ground on a workshop wheel or belt machine.
Arc Stability
Tungsten Electrode Tips ground with the TEG-3 Grinder, will be smooth and free from ridges, thus preventing erratic arc behaviour, arc flickering and arc instability.
|
|
|
|
|
|
APOLLO 13
DIAMETER OF APPLIABLE END-MILLS:
4-13 FOR 2 FLUTED AND 6-13 FOR 4 FLUTED END-MILLS
APPLIABLE SHAFT DIAMETER OF END-MILLS:
4-6-8-10-12
AXIAL ANGLES:
1 PRIMARY CUTTING ANGLE 6º
2 RELIEVE ANGLE 20º
3 END GASH 30º
Whetstone grinding wheel:
CBN 170 FOR HSS (DIA 170 FOR CARBIDE)
VOLTAGE:
+ -10% 220V AC 50/60HZ
ENGINE POWER:
100W - 7200 RPM
DIMENSIONS: 220x2220x200
WEIGHT: 4.8 KG
EQUIPMENT:
5 HOLDER TUBES
RING SUPPORT FOR 2 AND 4 FLUTED END-MILLS
ALLEN WRENCH 3 mm
ALLEN WRENCH 2.5 mm
BRUSH
CABLE CONNECTION
APOLLO 22
DIAMETER OF APPLIABLE END-MILLS:
12-22
APPLIABLE SHAFT DIAMETER OF END-MILLS:
12-16-20
AXIAL ANGLES:
1 PRIMARY CUTTING ANGLE 6º
2 RELIEVE ANGLE 20º
3 END GASH 35º
Whetstone grinding wheel:
CBN 270 FOR HSS (DIA 270 FOR CARBIDE)
VOLTAGE:
220V AC 50/60HZ + - 10%
ENGINE POWER:
300W - 6900 RPM
DIMENSIONS: 300x300x280
WEIGHT: 12 KG
EQUIPMENT:
3 HOLDER TUBES
RING SUPPORT FOR 2 AND 4 FLUTED END-MILLS
ALLEN WRENCH 3 mm
ALLEN WRENCH 2.5 mm
BRUSH
CABLE CONNECTION
1 Fast (only 2 minutes) in implementation.
2 No need any professional knowledge, anyone can use it.
3 Machine favorite of the head. You can reuse the end-mills.
4 Saving, increase profits, increase effectiveness of the production.
5 Saves time, money, material and end-mills.
(APL-13 edges up to 1500 pieces with the same grinding wheel)
(APL-22 edges up to 1300 pieces with the same grinding wheel)
6 Increase the life time of the end-mill (wearing nothing more than 0.2 mm)
7 You can reuse the end-mill 8 to 9 times.
8 10 times more precise than hand-sharpening
9 Applicable to 2 and 4 fluted end-mills of HSS and carbide.
10 Simple, compact, portable and secure.
|
|
|
Quickly sharpen a wide range of end mills. Renew endmills up to 1" in diameter and 6" flute length. Easily sharpen long flute end mills. The easy-pull handle allows precise control of the air-bearing spindle. You can pull and rotate the spindle the full length of the end mill without the necessity of re-positioning your hand. Increase your production. A sharp end mill will allow maximum machining rates as well as generating less heat in the process. Fewer burrs will be created, reducing the time necessary for finishing processes.
|
|
The Atritor DCM Mill is one of the most universal milling systems available with independently driven grinding and classifying sections.
It has a wide range of applications producing materials in some instances to less than 15 microns.
Feed material is metered into the mill pneumatically and first passes into the classifier zone where any fraction of the feed that is already inside specification is removed as product, thus avoiding any over-grinding. Oversize is recycled internally to the grinding zone and is returned to the classifier after further size reduction. This process produces a steep size distribution curve.
Adjustment of the classifier speed controls the size of the product leaving the mill. The product is conveyed pneumatically to a collecting cyclone and/or bag filter. With the application of heat to the inlet air flow, simultaneous drying can be undertaken.
|
|
Rhodax crusher
Principle
In-bed compressive grinding
Advantages
On load and on line setting
Non sensitive to tramp iron
Low wear rate
Stable quality of ground product fineness
Selective grinding and classification of the Fines which preserve hard grains.
|
|
Feature
It's suitable for any powder, granule and liquid. Easy operation and powder won't fly out. Screen could be changed speedily.
Application
Foodstuff, Chemical, Medicine, Mineral, Rubber, Plastic, Metal and the Kinds of Environmental ProtectionKetc.
|
|
|
|
see the results for the following category : 
