|
|
Dura-Sleeve return idlers are a patented abrasion resistant urethane sleeve that is easily clamped on any existing or new rubber or urethane disc return idler shaft.
* Patented Design - of our idler sleeve clamping system utilizes you to replace worn out rubber or other urethane disc return idlers.
* Abrasion Resistant Urethane - compounds provide wear ability that exceeds 5 times the wear life of standard rubber disc return idlers.
* Meets all CEMA Standards - and available in any belt width and inside and outside roller diameter.
|
|
| ... products without technical information |
| |
The Tru-Trainer employs a unique and highly effective tracking action, which is non-damaging to the belt and reacts immediately if the belt begins to drift off center.
Because it does not rely on contact with the belt edge in order to guide the belt, belt edge damage, which occurs frequently with other tracking systems, is avoided. The center pivot is unique and simple, consisting of a stainless steel pin within a solid steel center shaft. Advantages include:
- Simple to Install
- Maintenance Free
- Operates In All Conditions
- Increases Conveyor Belt Life
- Reduces Spillage and Waste
- Minimum Working Parts
- Lower Motor Power Consumption
- Operates on Reversible Belts
- Rubber Covered for Better Traction
|
|
|
|
|
|
MARTIN® TRAC-MOUNT™ Idler
MARTIN® TRAC-MOUNT™ Idler uses sliding frames to fit into tight spaces between cradles, ensuring proper rolling support for the belt.
Simple Service
Individual rollers slide in and lock in place from outside the belt. No more laying idler sets on their side.
Proper Conveyor Belt Support In Tight Spaces
Slide-in frames need only 8 inches (203 mm) of width for 6-inch (152 mm) rollers.
Meets CEMA Standards
Available for any belt width or troughing angle, with any brand of rollers.
MARTIN® Transfer Points are custom-engineered by Martin Engineering to eliminate blockages, reduce impact, centralize loading and guarantee the material flow rate.
Martin Engineering makes bulk materials handling cleaner, safer and more productive, with engineered systems including conveyor belt cleaners, conveyor load zone/transfer point chutes, impact cradles and slider beds, skirtboard sealing systems, air-supported belt conveyors, air cannons, pneumatic (air) and electric industrial/bin/railcar/truck vibrators, belt training/alignment devices, dust suppression/collection/control systems, and specialized contract services including installation/maintenance and silo/bin/bunker cleaning.
|
|
Tracker Rollers from HOSCH ensure conveyor belt alignment.
- Maintenance free
- No wearing parts
- Durable rubber surface
- Suitable for all environmental conditions
- Minimum space required, compact dimensions
- Ease of installation
- Minimum of installation
- Also suitable for reversing operation, ideal for retrofitting
|
|
The Chevron secondary belt cleaner uses the speed and force of the belt rolling over our patented rubber disks. The unique rotary fingers are forced against the base of the chevrons to dislodge material from the belt.
- Sweeping Action - of each disk cleans in front of and behind each and every chevron.
- Easy Maintenance - no motors, air nozzles, or other problematic equipment to maintain.
- Works Great - in the pulp and paper, fertilizer, potash, and other bulk material industries where chevron style belts are heavily used.
- Solid or Notched - 8” (200mm) diameter abrasion resistant rubber disks are available depending on the height of the chevrons and the conveyor belt speed.
|
|
|
Flexco Chevron Belt Cleaner takes a new approach to cleaning chevron, cleated, and raised rib belts. Hundreds of rubber fingers create a rotary cleaning action that easily flicks carryback off the belt. And without the typical clogging and rapid wear problems associated with brush-type cleaners. Now there is a better solution for wet sand belts, wood chip belts and other raised top or grooved belts.
|
|
|
Our brushing machine type BM 1138 has been constructed previously for heavy-duty conveyor belt cleaning in coal mines and foundries. Today we supply it for almost all kinds of industry where conveyor belts have to be cleaned.
|
|
|
|
|
|
MARTIN® Brush Belt Cleaners are specially suited for the removal of fines and residue from ribbed, flighted, grooved, or chevron belts. Versions are available to suit your conditions and your budget.
Motor-Driven Cleaning Action
One or two-horsepower motor (depending on belt width) turns brush against belt motion.
Match Cleaner To Requirements
Specify the cleaning system to suit your conditions and your budget.
MARTIN® Standard Brush Cleaner
MARTIN® Standard (Spiral) Brush Cleaner is value-priced answer to belt cleaning problems.
MARTIN® Strip Brush Cleaner
Uses 12 brush strips to form cleaner that sheds even moist material that would plug other brushes.
Brushes To Fit Need
MARTIN® Standard (Spiral) Brush Cleaner uses 0.38 inch (0.96 mm) polypropylene bristles wrapped in spiral around the hub. MARTIN® Strip Brush Cleaner forms brush from strips with 0.40 inch (1 mm) polypropylene bristles. Other materials and bristle diameters are available.
Martin Engineering is the world’s leading developer and manufacturer of engineered conveyor belt cleaning systems. In this position, Martin Engineering has developed fundamental principles of cleaner design that have set standards for belt cleaner engineering and performance.
The multiple-cleaner system originally adopted by Martin Engineering is now the standard for applications on belt conveyors carrying all types of bulk materials around the world. End users (and other cleaner manufacturers) have accepted it almost universally.
|
|
|
Using Low Back Pressure (LBP) conveyors, parts ride directly on a densely populated array of plastic rollers. The parts flow freely with very low friction and exert minimal force on adjacent parts.
|
|
EUROBELT® SERIES 40 SLIDING ROLLERS is provided with small rollers inserted on its surface that revolve whenever there is accumulation, avoiding crushing and damage in the base of the product.
Those rollers can be inserted in Flat Top or Flush Grid types of SERIES 40, so that you can choose the suitable type according to the requirements of the application. This belt has been designed mainly to solve problems of transport of boxes, containers ...
|
|
The Chevron secondary belt cleaner uses the speed and force of the belt rolling over our patented rubber disks. The unique rotary fingers are forced against the base of the chevrons to dislodge material from the belt.
- Sweeping Action - of each disk cleans in front of and behind each and every chevron.
- Easy Maintenance - no motors, air nozzles, or other problematic equipment to maintain.
- Works Great - in the pulp and paper, fertilizer, potash, and other bulk material industries where chevron style belts are heavily used.
- Solid or Notched - 8” (200mm) diameter abrasion resistant rubber disks are available depending on the height of the chevrons and the conveyor belt speed.
|
|
|
Flexco Chevron Belt Cleaner takes a new approach to cleaning chevron, cleated, and raised rib belts. Hundreds of rubber fingers create a rotary cleaning action that easily flicks carryback off the belt. And without the typical clogging and rapid wear problems associated with brush-type cleaners. Now there is a better solution for wet sand belts, wood chip belts and other raised top or grooved belts.
|
|
Mink round brushes - Highly efficient tools with countless applications
Mink round brushes can be applied to solve problems in a wide range of areas, and our engineers have the ideas to exploit this potential. When it comes to flexibility, no industrial tool can match these brushes. We offer a huge selection of models: roller brushes (with stub shafts), round brushes (with hollow centre spindle, no shaft), the Mink HP-System (two half segments, without shaft) and the Mink Zick-Zack-System (modules, with or without shaft). Finally, there are Mink web spreader brush rolls for modern processing of plastic film, textiles and many other kinds of web.
Advantages:
• Suitable for goods of all kinds
• Versatile and economical
• Maximum cleaning power combined with optimum surface care
• Form and stiffness according to individual requirements
• Less need for cleaning agents thanks to the mechanical action of the bristles – economic and ecological benefits
|
|
Mink roller brushes (BW) - Individually configured roller brushes with shafts
Mink roller brushes differ from other Mink round brushes by virtue of their integrated shafts. Owing to the wide-ranging demands made on these brushes, especially in terms of shaft dimensions, there is no advantage in maintaining a stock range. Nevertheless, with our extensive experience in this area we are able to configure special brushes for you very quickly. On account of its extraordinary versatility the Mink Zick-Zack-System can frequently serve as the basis for a reliable solution.
Your advantage:
• Individual configurations for special purposes
|
|
|
Our brushing machine type BM 1138 has been constructed previously for heavy-duty conveyor belt cleaning in coal mines and foundries. Today we supply it for almost all kinds of industry where conveyor belts have to be cleaned.
|
|
|
|
|
|
MARTIN® Brush Belt Cleaners are specially suited for the removal of fines and residue from ribbed, flighted, grooved, or chevron belts. Versions are available to suit your conditions and your budget.
Motor-Driven Cleaning Action
One or two-horsepower motor (depending on belt width) turns brush against belt motion.
Match Cleaner To Requirements
Specify the cleaning system to suit your conditions and your budget.
MARTIN® Standard Brush Cleaner
MARTIN® Standard (Spiral) Brush Cleaner is value-priced answer to belt cleaning problems.
MARTIN® Strip Brush Cleaner
Uses 12 brush strips to form cleaner that sheds even moist material that would plug other brushes.
Brushes To Fit Need
MARTIN® Standard (Spiral) Brush Cleaner uses 0.38 inch (0.96 mm) polypropylene bristles wrapped in spiral around the hub. MARTIN® Strip Brush Cleaner forms brush from strips with 0.40 inch (1 mm) polypropylene bristles. Other materials and bristle diameters are available.
Martin Engineering is the world’s leading developer and manufacturer of engineered conveyor belt cleaning systems. In this position, Martin Engineering has developed fundamental principles of cleaner design that have set standards for belt cleaner engineering and performance.
The multiple-cleaner system originally adopted by Martin Engineering is now the standard for applications on belt conveyors carrying all types of bulk materials around the world. End users (and other cleaner manufacturers) have accepted it almost universally.
|
|
|
The modular principle underlying our one-way system of trapezoidal toothed roller brushes provides for fast, low cost changes of brushes. They can be installed and similarly removed by a simple hand operation. The teeth lock securely (and in a non-twist manner); as a result, a gap-free bristle surface is assured. Precise true running is guaranteed at all times. The DT system consists of brush segments which are mounted to the brush core with two locking collars. Due to the special modular principle on which they are based, worn individual segments on a roller brush can be replaced
|
|
Mink round brushes - Highly efficient tools with countless applications
Mink round brushes can be applied to solve problems in a wide range of areas, and our engineers have the ideas to exploit this potential. When it comes to flexibility, no industrial tool can match these brushes. We offer a huge selection of models: roller brushes (with stub shafts), round brushes (with hollow centre spindle, no shaft), the Mink HP-System (two half segments, without shaft) and the Mink Zick-Zack-System (modules, with or without shaft). Finally, there are Mink web spreader brush rolls for modern processing of plastic film, textiles and many other kinds of web.
Advantages:
• Suitable for goods of all kinds
• Versatile and economical
• Maximum cleaning power combined with optimum surface care
• Form and stiffness according to individual requirements
• Less need for cleaning agents thanks to the mechanical action of the bristles – economic and ecological benefits
|
|
Mink roller brushes (BW) - Individually configured roller brushes with shafts
Mink roller brushes differ from other Mink round brushes by virtue of their integrated shafts. Owing to the wide-ranging demands made on these brushes, especially in terms of shaft dimensions, there is no advantage in maintaining a stock range. Nevertheless, with our extensive experience in this area we are able to configure special brushes for you very quickly. On account of its extraordinary versatility the Mink Zick-Zack-System can frequently serve as the basis for a reliable solution.
Your advantage:
• Individual configurations for special purposes
|
|
|
The modular principle underlying our one-way system of trapezoidal toothed roller brushes provides for fast, low cost changes of brushes. They can be installed and similarly removed by a simple hand operation. The teeth lock securely (and in a non-twist manner); as a result, a gap-free bristle surface is assured. Precise true running is guaranteed at all times. The DT system consists of brush segments which are mounted to the brush core with two locking collars. Due to the special modular principle on which they are based, worn individual segments on a roller brush can be replaced
|
|
Batch terminal
The batch terminal serves for the stacking of big packages for the laminated storage in trucks or journals and is offered as accessorie for conveyor belts,
weight categories up to 100kg per package
vertical lift up to 4 meters
dimension of the packages: from 400mm x 400mm x 400mm up to
1200mm x 1200mm x 1600mm
It is also possible to link it in manual workspaces.
|
|
|
|
see the results for the following category : 
