|
|
2320 SERIES RECUPERATIVE
RADIANT TUBE BURNER, SUCTION TYPE
CAPABILITIES Quiet stable operation Uniform tube temperature Conversion of existing Bloom gas fired recuperative radiant tube burners to combination gas and oil firing easily accomplished Suitable for 5”(127 mm) and 7” (178 mm)
and larger I.D. ‘U’ tubes or ‘W’ tubes and
can be mounted on either leg of the tube
|
|
The MAXON TUBE-O THERM® burner-to-tube direct firing system provides uniform heat transfer, eliminates "hot spots", and produces faster bring-up times than all other tube burners. This industrial burner fires directly into smaller-bore, less expensive tubes and burns butane, , propane or natural gas with reduced levels of NOx and CO.
TUBE-O THERM® gas burners ensure improved performance for industrial washers, dip tanks, water-bath heaters, and solution tanks.
|
|
The ImmersoJet (IJ) is a nozzle-mix tube-firing burner that is designed to fire at high velocities through small diameter immersion tubes.
The combustion gases from the burner scrub the inner tube surface and produce high heat transfer rates. This, in combination with the high velocity flow through the smaller diameter tubes allows for system efficiencies in excess of 80%.
The smaller IJ tubes also have smaller bends which means less tank space is occupied by the tubes. With a combustion chamber that is integral to the burner body, the new version of the ImmersoJet can sit lower on the tank than previous IJ models.
This burner is available with the Eclipse HeatPak packaged valve train - flame safety option.
system.
|
|
The ThermThief’s unique nozzle creates an intense, adjustable length flame with a vigorous spinning action. The flame scrubs the inside of the fire tubes to remove the gas film boundary layer and increase heat transfer effectiveness with outstanding temperature uniformity. Not only does this contribute to longer tube life, it also ensures consistently uniform product processing.
ThermThief delivers these additional benefits:
Low NOx and low CO.
Low excess air capability for high efficiency.
Low air and gas pressure requirements.
High heat transfer at low noise levels.
Reliable ignition at a wide range of firing rates.
|
|
TUBE-O-FLAME®
MAXON's TUBE-O-FLAME® industrial burners provide clean, low NOx heating for tube firing. The TUBE-O-FLAME® burns most fuel gases inside an array of tubes to provide reduced fuel consumption and better process response. The low horsepower requirements reduce operating costs, and produce clean combustion with outstanding reliability.
TUBE-O-FLAME® natural gas burners ensure improved performance for industrial washers, dip tanks, water-bath heaters, solution tanks, and asphalt tanks.
|
|
Burner with Compact Immersed Tube - Startub
Burner with mixture with the nose and tubular immersed exchanger
Characteristics:
- Output of about 90% on NCV
- Compactness
- Process leaving the clean baths
- Adaptation of the exchanger to the nature of the bath
- Together flexible adapting to the form and the size of the bath
|
|
The photomultiplier provides extremely high sensitivity and ultra-fast response. Photomultiplier tubes (PMT) have high bandwidth and noise-free gain on the order of a million. This makes them ideal for the detection of extremely low light or short pulses of light. Photomultipliers can be used to detect photons from 115nm to 1700nm. A typical Photomultiplier consists of a photoemissive cathode (photocathode) followed by an electron multiplier and an electron collector (anode).
Hamamatsu offers the most complete range of head-on and side-on photomultiplier tubes from 3/8" to 20" in diameter.
|
|
Toshiba offers a wide family of thermionic vacuum tube covers X-Ray tubes, X-Ray Image Intensifier, micorwaves tubes and a large variety of proportionnal counters.
Toshiba America Electronic Components, Inc. (TAEC) offers Magnetron Tubes for residential and commercial Microwave ovens as well as imaging system components for a variety of medical, dental and industrial applications. For the latter, the company has established itself as the single source for the complete image chain to meet the needs of all major applications. This product line includes x-ray tubes, a variety of image intensifiers (from 4- to 16-inches), optical units (lens, adapter and cover) and CCD cameras with up to 1K x 1K image resolution. All of TAEC's imaging components offer superior image sharpness, optimized uniformity and maximum image brightness.
|
|
|
Electron multipliers (EMT) are used for the detection and measurement of electrons, charged particles such as ions, VUV radiation and soft X-rays. Hamamatsu electron multipliers have high gain and low noise, making them suitable for the detection of very small or low energy particles. An EMT has CuBeO dynodes for producing gain via secondary emission. The dynodes are connected by a built-in voltage divider (1M ohm per stage) and are supplied in an evacuated glass bulb. The first dynode can be replaced by a photocathode of CsI or KBr for use in VUV photometry. Microchannel Plates (MCP) can also be used as electron multipliers. EMTs are used in applications such as mass spectroscopy, field ion microscopy, electron or VUV spectroscopy, Auger spectroscopy, AES and ESCA.
|
|
| ... products without technical information |
| |
UNIQUE GLOBAL SUPPLIER !
With the AXXAIR global concept you may upgrade the tube cutting machines from:
· simple orbital cutting
· to automatic orbital cutting
· to automatic orbital cutting and welding for prefab applications: CC+SASL
· to traditional orbital welding with closed heads: SASL+SATF
IN A FEW MINUTES ONLY !
|
|
Mechanized Pipe Welding System
The Piper Bug Pipe Welding System from Bug-O Systems is a digitally controlled programmable welding travel carriage integrated with Lincoln Electric® Invertec® V350-PRO Power Source. The Piper Bug features a positive rack and pinion drive system and a digital control box in which all welding parameters can be programmed for multi-pass, multi-layer welds on process piping and cross country pipe lines. The Piper Bug will increase productivity and weld quality while reducing costs.
|
|
|
|
|
|
Gullco PIPE KAT® Automated Pipe Welding System with integrated wire feeder unit incorporates 40 IPM welding carriage design with quick action mounting for ease of installation. The PIPE KAT® also comes equipped with a linear oscillator with adjustable weave width and weld joint centerline adjustment and all electronic motorized functions incorporate jog settings. The system comes with a main control box with 12 ft umbilical and 27 ft. of water hose and electrode cable, wire feed spool capacity of 10 lbs, with a maximum wire speed of 791 IPM and a wire size range of 0.8 to 1.4 mm. The welding torch uses Abicor Binzel consumables.
WELD TORCH AND WIRE IINFORMATION:
Welding torch uses Abicor Binzel consumables. Wire feed 10 lb. spool capacity. Maximum wire speed of 720 IPM. With a wire size range of .8 to 1.4 mm. All motors 24 volt DC.
Remote pendant on 12 ft. of cable incorporates carriage speed and jog, wire feed speed and jog, vertical slide adjustments, oscillation width and centerline adjustment with start/stop and emergency stop buttons.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
... see all the products in the category
Labware
|
The INFRA radiant module is the most classical expression for infrared heating for industrial buildings, sportshalls, ware-houses, poultry farms and glasshouses. The machine is made up of a burner working with forced induction in premix type Baf, with a multi gas head, exhaust fume electro fan, heat exchanger made up of special heat treated steel radiant pipes for high temperature; stainless steel reflecting metallic parabole and support hangers. It has low thermal inertia, and can heat single zones also with limited dimensions activating single modules, it does not move the dust in the air, does not take any space on the floor, it heats the bodies but not the air, so this means that the lower is building insulating, the higher are fuel savings that are achived with infrared radiant tubes.
|
|
Equipments suited for all environments with great height (form 4 to 20 meters) or with high thermal dispersion.
It includes a burner unit and a heat exchanger tube which reaches the temperature of 400 ÷ 550 °C., providing a very high radiation efficiency, also by means of the reflecting cover located over the tubes, which focuses the thermal flow downwards.
By means of a centralized equipment control system it is possible to heat only the areas concerned by operations
|
|
2 solutions available : Radiant heaters « U-tube » (U) or linear (L)
Alimentation Natural Gaz or Propane, horizontal or inclined
4 sizes 13 / 22 / 35 / 50 KW
Option : Régulation, stainless steel reflectors, double skin, dilatation rings …
Various accessories : Regulation kit, fume kit, gas conection kit ... etc
|
|
Radiant tubes Infra
Heating by radiation
Apparatuses INFRA of THERMIGAS can be suspended on the frame via chains or of ropes or be gone up out of mural bracket.
Components
- burner and extractor out of separate boxes facilitating the assembly and demounting and allowing indifferently to assemble one or the other on the ends of the pin.
- steel tubes with easily dismountable elbow, the whole being painted in workshop using a painting high temperature.
- indeformable and unbreakable steel self-supporting quality.
- stainless steel reflectors easily nettoyables. These reflectors comprise, on each side over a length a fold with 180° avoiding the sharp edges.
|
|
Evolix 250 - Sheath erasing with burner gas outside
Comfortable: temperature sheaths 200 °C
5 burners from 35 to 300 kw, length of the network of sheath up to 324 Mr.
Sheath monotube linear with generator 300 kw.
Buildings of great volume and up to 14 m height.
Buildings requiring a burner outside (maintenance, fire hazard...)
|
|
|
|
see the results for the following category : 
