|
|
|
|
|
|
The recently developed CUBEx control enclosure product line from R. STAHL now makes it possible to combine compex control and distribution panels into comprehensive, space-saving units. Adds a whole new dimension to individualised and flexible solutions for your applications. Other customer-specified control and distribution panel designs are also possible. The CUBEx system increases the flexibility of your applications and ensures that all internationally recognised installation technologies can be employed. All standard, commercially-available electrical equipment can be installed. The space-saving design of this IIB enclosure enables a mounting distance of just 10 mm between units. Moreover, flameproof enclosures incorporating "D2D" technology enable the direct connection enclosures or terminal chambers are required. CUBEx is the logical next step in the development of IIC tchnology integrated in the renowend 8220 Series. For use in Group IIB hazardous areas in Zone 1 and Zone 2 or Zone 21 and Zone 22.
The main connection switch of the lighting and heating panels CUBEx Series 8264/5-ExV is operated through the side wall via an actuation mechanism. The circuit breakers are fitted on the second mounting level and are actuated via totary drives. As an option it is possible to fit test keys to the ELCBs to make it possible to actuate the back wall of the enclosure for fixing the devices. Cable entry is done directly via tapped holes, wired directly to the switches. For current distribution the original comb type rails are used at the switching units. A typical design allows for 12 or 24 circuit breakers. Different designs upon request.
|
|
|
|
|
|
DIDO-S distribution boards are available in two types: surface mounted and flush mounted boards.
Particular attention has been set to the need to give more space in the inside in order to facilitate the operations of
wiring therfore favoring the simplicity of instalation.
PE4, PE8 and PE12 boards have a particular system to fix the DIN rail; it allows to regulate its height in two positions, an
inner and an outer.
Some Flush mounted boards (CMR) answering the demands of space saving products - more compact enclosures.
All distribution boards have DIN rail and brass terminal block (earth and neutral).
The particular structure of the lid, limits the board prominence from the wall of only 20 mm, creating a product of
discrete design and presence.
The interchangeability among the doors (transparent and opaque) and their reversibility together with the large
space for the assembling make these series very versatile.
Always careful to the demands of the clients, all products are protected with a thermo-retracable film.
|
|
|
|
|
|
FLUSH MOUNTING ENCLOSURES
*MADE FROM ABS TECHNOPOLYMER MATERIAL, WITH THICKNESS THAT ENSURE MAXIMUM STURDINESS AND STRENGHT IN EVERY POINT.
*WORKING TEMPERATURE -15° C TO +60° C
*RESISTANT TO HEAT UP TO 650° C GLOW WIRE TEST ( IN CONFORMITY WITH STANDARD: EN60335-1:94 +IEC 695-2-1 ).
*PROTECTION DEGREE IP40.
*PREMARKED MODULE COVERS, INTEGRATED ON THE FRAME.
*FRAME SEPARATED FROM DIN RAIL FOR CABLE CONNECTION AND INSTALLATION AFTER PAINTING.
*TRANSPARENT DOOR WITH LOCKING DEVICE ON OPENING.
*ENCLOSURES WITH MULTIPLE HORIZONTAL AND VERTICAL MODULAR COMBINATIONS BY MEANS TO ITEM GR11028.
*MARKED CE
*AVAILABLE ON REQUEST WITH HEAT RESISTANCE 960 °C GLOW WIRE TEST
SURFACE ENCLOSURES
*MADE FROM ABS TECHNOPOLYMER MATERIAL, WITH THICKNESS THAT ENSURE MAXIMUM STURDINESS AND STRENGHT IN EVERY POINT.
*REMOVABLE FLANGE TO SIMPLY SWITCH HOUSING AND WORK INSIDE THE DISTRIBUTION BOX.
*THE FLANGE ON THE INNER SIDE, NOT VISIBLE FROM THE OUTSIDE, IS PRE -CUT FOR ALL STANDARD TUBE AND CABLE-TRAY DIMENSION.
*THE DIN PROFILE FOR HOUSING THE SWITCHES IS HIGHER OFF THE BOTTOM TO PERMIT ALL TYPES OF WIRING WITHOUT ANY SPACE PROBLEMS.
*WORKING TEMPERATURE -15° C TO +60° C
*RESISTANT TO HEAT UP TO 650° C GLOW WIRE TEST ( IN CONFORMITY WITH STANDARD: EN60335-1:94 +IEC 695-2-1 ).
*PROTECTION DEGREE IP40.
*IN COMPLIANCE WITH CEI 23-48 -I ED.1995 PRODUCTS MEETING ESSENTIAL REQUIREMENTS OF L.V.D. 73/23/EEC AND FURTHER AMMENDMENTS ( IEC 760 2 ED 1989, AM 1/1994 AND MODIFICATIONS PR. EN60670 )
*MARKED CE AND IMQ.
*AVAILABLE ON REQUEST WITH HEAT RESISTANCE 960 °C GLOW WIRE TEST
|
|
|
|
|
|
The Tern Way 800 pan assembly has been designed for easy installation, ideal for switchboard manufacturers and a wide range of specifications. A short time withstand rating of 35kA or 5()kA for I second makes this assembly one of the most versatile on the market. Busbar raiings are available at 800A and 1250A.
Key Features
• Busbar assembly and MCCBs manufactured in U.K.
• Fully shrouded busbars.
• Four possible frame sizes for outgoing MCCBs.
• Shrouding to IP20 protection.
• Terminal covers available for both line and load side terminals. (line side fitted as standard).
• All MCCBs are padlockable in both ON and OFF position.
• Easy connection onto assembly.
Specification
Manufactured in accordance with BS 5486 Part 1 (1990)/ EN 60 439-1 (1990). Busbar ratings 800 Amps and 1250 Amps. Fully tested for both 35kA and 50kA short lime withstand for 1 second. 6. 12 and IS triple pole versions which accept outgoing MCCBs from 125A frame size single pole to 250A frame size triple pole. 3 way triple pole version which accepts outgoing 400A frame size triple pole MCCBs.
|
|
|
A range of truly versatile MCB distribution board systems providing unobtrusive final circuit management solutions for applications up to 200A. The range offers robust TP&N and SP&N distribution boards with an extensive selection of MCBs, RCBOs, RCCBs, switch disconnectors, MCCBs, fuse switch incomers, service centres and modular control and command devices.
|
|
Explosion-proof boxes
Explosion-proof boxes, control stations and panels EEx d IIB and IIC, aluminium alloy, steel or stainless steel (316L), with front window, box extension. Boxes assembling.
|
|
Switch and control systems
- Electric switch and control systems
- Marshalling and distribution panels
- Electrical switch panels in accordance with national and international standards
- Special cabinets (steel, stainless steel, aluminum) for instrumentation, control and electro-technics and for use in hazardous areas
BARTEC BENKE designs and manufactures control system solutions for automation of machines and processes.
|
|
Individual switch cabinet construction
- Console control cabinets Material: Stainless steel with subsequent powder coating, textured finish
- Stainless steel box without surface treatment
- Ethernet switch housing made of steel sheet with finaly-structured powder coating
|
|
-Lift off screw cover type
1. Available 2 plastic type of non-flush handle screw(indluded) or flush cross screw(optional)
2. Reinforced self-threaded design
3. Type 4X&IP67 for indoor&outdoor application by neoprene gasket seal
4. Available 48 kinds sizes from 50x65x45 mm to 380x560x180 mm
5. Selectable gray or clear cover
6. Available stainless steel wall mounting bracket
|
|
The product weighs approximately 1/4 the weight of an iron box and can be easily installed or moved. The product is free from corrosion, carries superior insulation.
The product has passed waterproof and dustproof tests carried out under rigid quality standards. ( IP 66 -67)
The use is also convenient for the installation of Terminal Substitution Rail, Button Box, Small Terminal, Signal, Relay and Sensor, Communication and Joint Box etc.
Refer to our E-Catalog on Direct-Industry. There are more story.
|
|
|
Vibra-metrics offers a full line of six through 48 channel NEMA 4 vibration sensor switchboxes which allow safe and speedy data collection in dangerous or inconvenient areas. Since probes are mounted permanently, more repeatable and useful data is gathered, improving your PdM process.
|
|
|
ARETA is not just a Modular cabinet but a complete system, which allows several solutions for the distribution and automation business. Thanks to the well designed orthogonal joint, the cabinet can be mounted in only a few minutes. The mounting operation is restricted only to 8 screws and all the other alloy manufactured accessories (hinges, fixing elements, etc.) are ready to be used. The cabinet profile has been well engineered and the result provides all the safety, strength and modularity standards. Profile and orthogonal joint are welded together using the very latest in laser welding technology.
|
|
We design and assemble electric panels for:
- Driving DC motors with their own drivers and protections
- Startup controls and protections for AC motors
- Panels with converter and synchronized inverter slots
- Commands and signaling for many applications and functions
- Control and automation of many different machines
|
|
GE's industrial-duty switchboard product lines Power Break® II and AV-3 AccessTM
Power Break II (PB) switchboards can house insulated case circuit breakers as mains, ties, and feeders; and low voltage power circuit breakers as mains and ties. AV-3 Access (AV3) provides individual compartments for molded case breakers serving as mains, ties, or feeders.
Feature:
Rugged construction - Designed bus structure (30 cycles )
Fast cycle times
Broad Functionality
Multiple locations
Cost effective design
|
|
There is a total of more than 50 production staff spread over five assembly shops and a test workshop.
We have spent the last 40 years making electrical cabinets; this has enabled us to build up a very significant experience. Our way of working consists in helping and advising our customers as from the development of their project. We suggest that the end product is pre-accepted or accepted on our premises, in order to make sure that it corresponds exactly to your needs.
Thanks to our teams' expertise, we are able to manufacture the following complex technical units:
- tertiary cabinets,
- modular cabinets,
- automated system cabinets,
- TGBTs (general low voltage panels),
- machine-tool cabinets,
- pneumatic cabinets,
- 1-2-3 type units with service indices ranging from IS 111 to IS 333.
|
|
| ... products without technical information |
| |
The Fuserbloc CD's mean that SOCOMEC has a wide range of fuse switches on the market
The Fuserbloc CD's incorporate functions which make them simpler to fit and use.
Application:
Load-break and protection for low voltage installations and equipment
The range consists of:
25A - 32A - 50A – 63A – 100A – 125A – 160A – 250A – 400A – 630A – 800A – 1250A
Original features and advantages:
The Fuserbloc CD's can meet all the requirements of installers and users:
- The same product reference can be operated from the front, from the door or from the side
- The range includes the "Test" function as standard, so that auxiliary circuits can be tested without connecting the power.
- A patented system gives the customer the option of front or rear connection for the equipment.
- Modular design so that 2-pole products can be used in DC installations together with 6, 8, 12 etc. pole equipment so that several loads can be controlled with the same handle
|
|
Fused isolator switches from 32 to 1250 A
Description
For NFC or DIN, BS, UL type fuses
3 or 4-pole
For direct operator, external front-mounted and RH side-mounted operators, external LH side-mounted operator
Robust and compact handles : padlockable using up to 3 padlocks, lockable, with door interlock, black/grey or yellow/red, IP65 or IP55
Auxiliary contacts:
» Two early break and “O” and “I” position signalling auxiliary contacts, configurable and common throughout the range (GS1AM110 and GS1AM101)
» Auxiliary contacts GS1AN suitable for isolation. Reversibility of these contacts to convert a N/C contact to a N/O contact and vice versa
» Off-load control circuit test facility, with auxiliary contacts GS1AM110, GS1AM101 or GS1ANT used in conjunction with handles GS2AHT
» Auxiliary “blown fuse” signalling contacts.
|
|
|
|
|
|
Fuse switch-disconnectors from 32 A to 800 A
Description
Nominal current from 32 to 800 A
Voltage rating up to 690 V (AC) and 750 V (DC
3 and 4 pole version
Test position
Indication by fuse operating mechanism
Positive contact indication
Fuse compartment with IP20 protection by insulating covers as standard
Locking device to prevent access to fuses when the switch is in the "ON" position
Upstream-downstream double insulation
Reversed power supply
Compliance with standards IEC 947-1,-3,-5, EN 60947-1,-3 and -5, IEC 60269-1 to -4, EN 60269-1 to -4, BS 88-1 to -4, DIN 43620, NFEN 60269-1 to -4, NFC 63220
Specificity of the INF family:
Nominal current from 32 to 800 A
Nominal current from 32 to 800 A
Available in 7 sizes
Can be used for all NFC, BS, DIN fuses
Specificity of the ISFT/ISFL family:
Nominal current from 100 to 630 A
3 sizes in ISFT (100, 160, 250-630 A)
2 sizes in ISFL (160, 250-630 A)
Several installation types: mounting plate, DIN rail (ISFT) or on busbar (ISFT/ISFL)
Connection by cables or on busbar
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
