|
|
|
|
|
|
Conax Technologies multiple hole sealing glands seal from 1-50 probes, tubes, wires or fiber optic cable in a single gland. Immersion lengths can be easily adjusted in the field and elements may be set at different lengths to monitor multiple points. Irregular shapes and patterns are available. A high density feedthrough is also available to accommodate up to 240 conductors.
Features:
Seals 1 or More Elements
For Gas or Liquid
Stainless Steel Fitting
"Soft Sealant"
Adjustable Immersion Length
Selected Elements Can Be Readily Replaced
Reusable
Wires Easily Assembled or Replaced In Field
Temperature Range From -400°F to +1600°F (-240°C to +870°C)
Pressure*: Vacuum to 10,000 PSI (690 bar)
Application Ideas:
MHM glands can be customized to accommodate special hole patterns, irregular shapes and higher density requirements for gradient thermocouple, RTD or thermistor probes, tube bundles, liquid level sensors or other devices.
Replacement Sealant (RS) available, consisting of sealant only.
Example: RS-MHM5-040-16-T
|
|
WISKA QUIXX. Push in, pierce through, ready.
There is no easier way to insert a cable with protection grade IP 66. For QUIXX we transferred the soft membrane technique from junction boxes to cable inserts.
|
|
General description:
The Roxtec RS PPS back-to-back seal has been developed specifically to address the challenges of plastic pipes passing through pressurised and fire rated areas. The seal consists of two Roxtec seals that protect against water and gas leakage. An intumescent sealing strip in the middle expands when the plastic pipe burns through, and fills the empty space to stop any fire from passing through.
|
|
TKS - KLIKSEAL®
Klikseal is a revolutionary two-component grommet with cable anchorage - something completely new to the market.
Through innovation and advanced production technology, we have designed a product that has many of the advantages found in a cable gland.
Apart from the cable anchorage, Klikseal is compact, self-adjusting to its surrounding wall thickness (patented), click-fixed in place (patented), has a membrane seal, is waterproof, requires very little effort to install with its collapsible outer membrane (patented), and saves up to 90% of your time.
The installation of a Klikseal requires no tools and has a
pop-out membrane that is a permanent seal until penetrated by a cable or pipe. Each size of Klikseal can be used with an exceptional range of cable and pipe diameters. An M25 can be used for cables and pipes ranging from 4 mm to 14 mm. Because of its compact design, the Klikseal only extends 5,7 mm outside the housing on which it is mounted.
|
|
TSS
The TSS is the latest addition to the TST product range.
What makes the TSS different from existing products on the market are the built-in features that you normally do not find in this otherwise relatively simple product.
TSS handles an exceptionelly large cable span.
With the ”pop-out-membrane” you always have a round opening and are guaranteed to have IP67.
The TSS is equipped with a sock that closes tight around the cable and allows for it to be moved around like a ”joy-stick” in the opening without endangering the IP-classification. So it works extremely well with cables passing through
at an angle.
These are some of the features that creates a lot of value added in the TSS, and makes it a unique product.
|
|
TRS - RUTASEAL LIGHT®
Rutaseal Light® is designed for strip lighting manufacturers and similar applications. Less material makes it lighter and easier to install, while providing IP67 protection.
Suitable for holes in materials of 1 - 4mm thickness.
• Quick and simple assembly without the use of tools
• Resistant to chemicals
• Weatherproof
RUTASEAL LIGHT® is very simple to use and demands no tools, which in turn means lower work cost. It requires no screwdriver or scissors to make the hole, which otherwise would endanger the IP Class seal.
RUTASEAL LIGHT® is SEMKO tested for IP67 internally and externally.
RUTASEAL LIGHT® is produced of EPDM in Metric sizes. The seals are produced in black, light grey and grey. RUTASEAL has a very high finish and the automatic method of production guarantees the same even and high quality on all products.
|
|
RUTASEAL is very simple to use and demands no tools, which in turn means lower work cost. It requires no screwdriver or scissors to make the hole, which otherwise would endanger the IP Class seal.
RUTASEAL is SEMKO tested for IP67 internally and externally. The chloroprene version is also DNV approved.
RUTASEAL is produced in EPDM and Chloroprene in both PG and Metric. The seals are produced in black, light grey and grey. RUTASEAL has a very high finish and the automatic method of production guarantees the same even and high quality on all products.
|
|
|
|
|
|
Design-A-Flange is an innovative modular system where inserts can be changed depending on your needs. You can design you own configuration based on how many openings you want, where you want them placed, and what type of seal you want to have. You are no longer forced to use a fixed flange with a certain number of pre-determined openings. You choose the configuration that suits your needs.
The push-out membranes ensures fast and easy installation without worries about achieving the correct IP-level. Should you want cable anchorage on certain cables then just install a Klikseal or a cable gland in the flange. If a cable no longer will be used you can seal the opening either by replacing the insert or cutting out the membrane and sealing the opening with one of our grommets.
Design-A-Flange offers a number of features that you cannot find in any other flange solutions
- Design you own configuration, with the right size openings, and right number of openings placed where you want them.
- Push-out membranes to make installation fast, easy and fool-proof.
- High IP-protection.
- No need to drill separate holes to install a Klikseal or a cable gland.
- The inserts are easily changed to adapt to new needs.
- Very easy to seal an opening that no longer will be used.
|
|
DIMENSIONS
Lenght 430mm - 16.9"
Width 260mm - 10.2"
Height 310mm - 12.2"
Weight 10.3 kgs - 22.6lbs
FEEDING
Pressure Range 5.5 -7 bar / 78 -99 psi
Air Consumption 12 L/s - 25 cuft/min
PERFORMANCE
Max Tension Force 9000N -6.5bar-92psi
Tensioning Speed 6mt/m
Sealing seal double notches
Joint strength 80% of the breaking strength
|
|
DIMENSIONS
Lenght 350mm - 13.8"
Width 140 mm - 5.5"
Height 170 mm - 6.7"
Weight 4 Kgs - 8.8 lbs
FEEDING
Pressure Range 5.5 -7 bar / 78 -99 psi
Air Consumption 12 L/s - 25 cuft/min
PERFORMANCE
Max Tension Force 3000N - 4500N -6.5bar-92psi
Tensioning Speed 5mt/m 4500N - 7mt/m 3000N
Sealing seal single notch
Joint strength 80% of the breaking strength
|
|
RECORD
Economical machine especially suited for strapping voluminous packs and pallets. The strapping head is placed on the side of the machine frame.
The sealing head guarantees high seal efficiency for PP or PET strap.
Admitted strap size : 9 - 12 or 16 mm width.
OPTION :
- Automatic sword permitting passage of the straps through the pallet beams.
- Sealing head movable
- Automatic roller conveyor.
|
|
JN-85YMA
Features:
- The machine utilizes a fixed rail for sealing head travel (200-300mm), ensuring close proximity of the sealing head to large packages, and a tight strapping effect. It is equipped with pneumatic cylinder to drive hydraulic movement system.
- This machine is designed for large packages that can align to the sealing head (area).
- Installation with conveyor and photocell is essential.
- This machine requires compressed air source to drive an oil cylinder and makes machine move stable.
- Equipped with warning alarm and buzzer to notice failures of feeding strap.
- P.E.T strapping system is available as an option.
|
|
| ... products without technical information |
| |
Camozzi offers a large selection of fittings and accessories suitable for a wide range of applications. Universal fittings, super-rapid fittings, quick-release couplings and accessories are available in different dimensions from M5 to G1/2. Our fittings range includes the patented and longstanding “Sprint” system that guarantees tightening and facilitates the repeated removal and reassembly of the fitting.
|
|
|
DSTI offers a number of standard & custom union designs that have been used in the robotics industry. These assemblies can be used to transfer air & electrical signal data to & from the rotating gripper.
|
|
|
|
|
|
Cap Inspector
The Cap Inspection System is specifically designed to be used with any induction heating cap sealing equipment. The advanced features and the flexibility of the system allow it to monitor a wide range of container sizes at various conveyor line speeds. The Cap Inspector will detect and respond to a number of faulty conditions occurring during the induction cap sealing process.
Features:
- Detects all typical fault conditions on a conveyor line during the cap sealing process: Missing Cap, Bottle Misalignment (offset from center line), Cocked or unscrewed cap, Bottle Down, Idle State / No Bottles.
- 4 Relay Outputs (Ready/Fault, Monitoring On, Line, Ejector)
- Easy to operate and user friendly design.Self learning "AUTO CONFIGURATION" feature.
- The Ejector (not included) can be located up to 10Ft away from the sensing system.
- 2x20 LCD Display with Backlight. 3 additional Status LEDs.
- Universal Supply Voltage (95 to 250V AC).
- Productivity rate (bottles/min) is constantly monitored and displayed.
- Small, compact, watertight design.
|
|
| ... products without technical information |
| |
The bearings of industrial rotating equipment operate under arduous conditions - often for considerable periods of time. The most reliable indicator of bearing condition is the temperature of the metal beneath the shoe.
Recognition of rising temperature can provide a warning of the breakdown of the lubricating oil film; thus allowing machine shutdown and maintenance to take place - avoiding the probable catastrophic failure of the bearing and possible damage to its mounting. Conax Miniature Bearing Sensors provide a simple and cost-effective method to monitor bearing temperatures.
Features:
- For embedded applications in rotating machines
- RTDs - 100 ohm platinum, 0.00385 ohm/ohm/°C
- Thermocouples types J, K, T & E
- Single and duplex sensors
- Various styles and sizes
- Operating Temperature: to 250° F ( 120° C)
|
|
Miniature Bearing (MBS) Sensor
A critical indication of the status of bearings on large rotating plant is provided by their running temperature.
Due to its small physical size the miniature bearing sensor can be positioned close to the bearing surface allowing it to sense any early change in temperature.
These devices are available in both thermocouple and PT100 resistance thermometer format and can be supplied as either single or duplex sensors. The sensor lead wire insulation is in PTFE and if necessary lead wire jackets can be protected with stainless steel outer braid.
BSWS Bearing sensor wire seal assemblies are low temperature/low pressure glands for embedded sensors to prevent oil wicking along the sensor leads. They seal on the individual insulated leads exiting an oil-filled bearing housing.
Typical aplications are motors, turbines, pumps & journal bearing pedestals.
|
|
The W70 offers an economical solution to a wide variety of mix proof processing applications. Flow of two different media through the same valve simultaneously, without the potential for mixing, provides increased operating efficiencies and significant production cost savings.
- 1½" through 4" tube size
- 150 p.s.i. product pressure rating
- Sturdy, machined spherical bodies. One piece or two piece body construction available.
- Elongated center to face body dimensions for easy manifolding
- Tee or cross configurations; "S" line, "I" line or butt-weld port connections
- Tri-Ring FKM (Fluoroelastomer) or EPDM seats
- Micro switches or proximity switches; with or without solenoid valve
|
|
| ... products without technical information |
| |
The "Plug 'n Pack" concepts made by BEHN + BATES unify the applicator, filling and sealing technology in one compact, pre-assembled and dust-tight unit that ensures a low-noise filling operation and shortest assembly times as the test operation is carried out in our workshop already.
Our "Plug 'n Pack" concepts can be integrated even into smallest spaces.
|
|
KVM: Bag Filling and Closure Machine
For Packaging Of Products With Advertising Appeal.
Top-Closing Machine KVM 10 with customer-specific bag head shaping modules.
Highest Flexibility:
At a set performance of 80 bags/min., various types of top closure can be manufactured:
simple sealed top seam
180° folded top seam, closed
bag closed by clip
peel seam closure
label closure
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
