|
|
The CAGE-NUT is a square steel or stainless steel nut enclosed in an elastic metal cage.
- The CAGE-NUT allows tolerance in alignment or positioning.
- Hand-operated installation by compression of the cage in the indenting device.
- Dimensions: M3 to M12
|
|
The cage-nut allows a fast fastening in thin metal sheets, already punched.
Advantages : can be put in and off rapidly
Dimensions : From M3 to M10 ex-stock, other dimensions under request.
Material : Cage in steel or stainless steel, nut in steel or stainless steel.
|
|
|
|
|
|
|
CN Cage Nuts represent the traditional European metric size based products used for years in all aspects of European manufacturing. The greater variation on panel ranges has allowed these products to superceed the traditional UK sizes which were limited to only two panel ranges.They are totally interchangeable with the old standards but offer the designer greater choice of Hole Sizes and Panel thicknesses. They are particularly usefull where the advantage of floating thread forms are required to overcome out of tolerance mating parts. The fact that the nut floats in the cage offers a simple cost effective solution to this otherwise expensive problem. The cage nut can be used in blind applications; it can be fitted after painting of the panels and so offers the designer lots of advantages. Traditionally offered in Zinc and Yellow Passivate and in Stainless Steel these parts can be supplied with a combination of plated nuts with Stainless Steel cages or vice versa. Code 40111 M?? 40 defines Spring steel cage, steel zinc/yellow nut. Code 40112 M?? SS defines Stainless cage Stainless nut. Code 40113 M?? 4S defines stainless cage, steel zinc/yellow nut. HSL, in line with all other manufacturers of spring steel clips, refuses to accept liability for any premature failure of any spring steel part it supplies with an Electro-Plated Finish that has been specified by the customer, due to uncertainty regarding the incidence of, identification of, control of and removal of Hydrogen Embrittlement. Despite accurate processing controls, baking/anealing cannot be relied upon to guarantee removal of Hydrogen. We strongly recommend alternative finishes be specified.
|
|
... see all the products in the category
Nuts
|
The CAGE-NUT is a square steel or stainless steel nut enclosed in an elastic metal cage.
- The CAGE-NUT allows tolerance in alignment or positioning.
- Hand-operated installation by compression of the cage in the indenting device.
- Dimensions: M3 to M12
|
|
The cage-nut allows a fast fastening in thin metal sheets, already punched.
Advantages : can be put in and off rapidly
Dimensions : From M3 to M10 ex-stock, other dimensions under request.
Material : Cage in steel or stainless steel, nut in steel or stainless steel.
|
|
|
|
|
|
|
CN Cage Nuts represent the traditional European metric size based products used for years in all aspects of European manufacturing. The greater variation on panel ranges has allowed these products to superceed the traditional UK sizes which were limited to only two panel ranges.They are totally interchangeable with the old standards but offer the designer greater choice of Hole Sizes and Panel thicknesses. They are particularly usefull where the advantage of floating thread forms are required to overcome out of tolerance mating parts. The fact that the nut floats in the cage offers a simple cost effective solution to this otherwise expensive problem. The cage nut can be used in blind applications; it can be fitted after painting of the panels and so offers the designer lots of advantages. Traditionally offered in Zinc and Yellow Passivate and in Stainless Steel these parts can be supplied with a combination of plated nuts with Stainless Steel cages or vice versa. Code 40111 M?? 40 defines Spring steel cage, steel zinc/yellow nut. Code 40112 M?? SS defines Stainless cage Stainless nut. Code 40113 M?? 4S defines stainless cage, steel zinc/yellow nut. HSL, in line with all other manufacturers of spring steel clips, refuses to accept liability for any premature failure of any spring steel part it supplies with an Electro-Plated Finish that has been specified by the customer, due to uncertainty regarding the incidence of, identification of, control of and removal of Hydrogen Embrittlement. Despite accurate processing controls, baking/anealing cannot be relied upon to guarantee removal of Hydrogen. We strongly recommend alternative finishes be specified.
|
|
|
... see all the products in the category
Inserts
|
|
|
