|
|
Grip seals GPN 305
For the protection of tubes, bore-holes and internal threads
Material: EVA
Colour: yellow
Grip stoppers GPN 310
Particularly suitable for the protection of bore-holes and internal threads.
Material: PE-LD
Colour: red
Grip stoppers GPN 315
Similar to the 310 Series, but with a larger cover flange.
Material: PE-LLD
Colour: yellow
Grip seals GPN 330
For the protection of bore-holes, internal threads and especially for pipe ends with screw-cap joints.
Material: PE-LD
Colour: yellow
Grip seals GPN 335
For the transportation and storage of hose fittings.
Material: PE-LD
Colour: yellow
Grip stoppers GPN 630
The stopper - flexible, rubber-like material - is inevitably rolled up during disassembly. |
|
I003: Diam.
I. 10 to I. 160 mm
|
|
Square plugs GPN 260
For special section tubes, press fit by means of distinctive disks.
Floor leveling plugs GPN 265
Vertical adjustment by an adjusting screw with an extra strong hexagonal top.
Rectangular plugs GPN 270
For special section tubes, press fit by means of distinctive disks. |
|
I002: LxH
I. 10X10 I. 12X12 I. 13X13 I. 15X15 I. 16X16 I. 18X18 I. 20X20 I. 22X22
I. 25X25 I. 28X28 I. 30X30 I. 32X32 I. 34X34 I. 35X35 I. 38X38 I. 40X40
I. 45X45 I. 50X50 I. 52X52 I. 55X55 I. 60X60 I. 65X65 I. 70X70 I. 75X75
I. 80X80 I. 90X90 I. 95X95 I. 100X100 I. 110X110 I. 120X120 I. 140X140
I. 150X150
|
|
CTR :
- Filler breather with strainer - Tank top mount
CTR/2 :
- Filler breather with strainer - Tank top mount
FSB :
- Metal filter breather with strainer |
|
TCAZ/TCASZ :
- Knurled plugs with dipstick
- Knurled plugs with dipstick and breather hole
TCA/TCAS :
- Hex plugs with dipstick
- Hex plugs with dipstick an breather hole
TMDA/TMDFA/TMDFA-BR :
- Filler breather with large breather hole and dipstick
- Filler breather with large breather hole, dipstick and filter
- Filler breather with large breather hole, dipstick and filter in sintered bronz
TMDFA/AL :
- Filler breathers with dipstick, anti-splash disc
TMDAV :
- Filler plug with one way air vent valve and dipstick
TPA/TPFA/TPAV :
- Press-fit filler breather with large breather hole and dipstick
TPBA/TPBAS/TPBAF :
- Low profile press-fit plug with dipstick
- Low profile press-fit plug with breather and dipstick
- Low profile press-fit plug with breather, filter and dipstick
TFA :
- Filler breather caps with internal thread and dipstick
AL/1 - AL/2 - ALS/1 - ALS/2 :
- Dipstick, press-fit with one seal
- Dipstick, press-fit with 2 seals
- Dipstick, press-fit with one seal and breather hole
- Dipstick, press-fit with 2 seals and breather hole |
|
TYPE: DN/DS
Long plug with large flange especially suitable for sealing the female part of quick connectors on brake and fuel lines. The length of the plug ensures tight internal closure. The flange protects the external surface, and makes the plug easy to remove. Most of them are with or without tabs, to match packaging and ergonomics.
Some plugs meet the requirements of SAE J2044 standard; therefore the dimension given for the diameter is not that of the plug itself but of the nominal size of the pipe for which it is suitable. |
|
TYPE: DA
The DA type is ideal for holes in plate work as a cover plug, or in pipe ends when a smooth finish is required. The head of the plug is flat. |
|
- Material : Polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.
- Maximum continuous working temperature
120°C. |
|
| ... products without technical information |
| |
|
|
