|
|
| Murata's capacitors manufacturer, manufactured from our own superior ceramic materials, meet the demands of a wide variety of applications in voltage ratings from under 3V to several thousand volts. Based on our unique design and processing technologies we offer a variety of chip MLCC products from the ultra small 0402 size devices, through high capacitance products designed to replace tantalum and electrolytic dielectrics, low ESL, high frequency and array products. In short Murata has a ceramic capacitor to meet virtually every possible application. We also offer a wide range of trimmer capacitors including ultra small and thin types. |
|
Specifications
1. Operating Temperature : -25°C ~ 85 °C
2. Capacitance Range : 1.0 ~ 120.0 µF
3. Capacitance Tolerance : J = ± 5%, U= 10 ~ - 5 % , K = ± 10%.
4. Rated Working Voltage Range : 250 ~ 500 Vac 50/60 Hz
5. Withstand Voltage Test : ( A ) Dielectric strength test ( TV ):
Rated Voltage x 175 % for 1-5 Sec ( B ) Between Terminals and Case( TC ): Rated Voltage x 2 1000V for one minute, at 25 °C
6. Dissipation Factor ( DF ): 0.5 % MAX. When measured at 1 KHZ, 25 °C
7. Insulation Resistance ( IR ): ( A ) Between Terminals: Above 1000 F,at in 100VDC in 25 °C ( B ) Between Terminals and Case: Above 10000m, at 500vdc in 25 °C
8. Pull Test : Will sustain 2 Kg steady pull in the direction of lead egress and 1 Kg steady pull atany 90 degree angle for 60 seconds.
After test, manufacturers of capacitor shall show no evidence of damage and pass all electrical requirements
9. Damp-heat Test : capacitor are subjected to an environmental test chamber at R.H. 90 to 95 %,operating temperatures for 240 hours.
After the test, capacitor shall be conditioned at room temperature for 2 hours and meet the following criteria:
( A ) Capacitance change shall be less than 3%
( B ) Dissipation factor shall be less than 0.2 %.
( C ) Insulation resistance shall be over 50 % of the minimum requirement.
10. Life Test : ( on-off ) 100,000 cycle ± 5000 times on 2 seconds off 2 seconds at operating temperatures with rated voltage. After the test,the capacitance drift 5 %, dissipation factor 0.5 %, insulation resistance 50%.
|
|
NIC Aluminum Electrolytic Industrial capacitors are world renowned for their long life and high levels of performance. Advanced techniques in the etching and
forming of aluminum foil provides greater volumetric effi ciency and high reliability. Along with high purity materials and advanced production technology,
stringent quality control insures your company of the best possible components. Unique NIC part numbers are used to identify RoHS compliant aluminum
electrolytic capacitors through-out the supply chain. |
|
Technical Data
1. Dry manufacturer of capacitors (epoxy, oil-free)
2. Plastic case (corrosion-free)
3. Voltage rating : 120V to 660V AC
4. Frequency : 50/60 Hz
5. Capacitance range: 1.0µF to 100.0µF
6. Capacitance : ± 5%
7. Temperature range : -25°C to 105°C max
8. Dissipation factor : 0.5% per one KHz
9. Approval : UL810.CUS and EIA-456.JIS-4908. and IEC
10. Plastic capacitors : models with leads or with terminals 6.35±0.1mm (quick connection; M 8 x 10mm)
11. Test voltage between terminals and containers : 3KV 60/50Hz for one minute
12. Test voltage : 1.75time RV, one minute
13. Pull test : Will sustain 2Kg steady pull in the direction of lead egress and 1Kg steady pull at any 90 degree angle for 60 seconds
After test, capacitor shall show no evidence of damage and pass all electrical requirements
|
|
AVX manufactures a broad range of MLC supplier of capacitors including popular dielectrics like NP0, X5R and X7R. In addition we can supply specialty products like 150C X8R dielectric http://www.avx.com/docs/Catalogs/cx8r.pdf , SnPb and FLEXITERM termination devices.
If you have any specific requirements, please contact your local AVX sales office for details on how AVX Ceramics can assist you in addressing your future requirements. www.avx.com
|
|
Multilayer Ceramic capacitors
Case size: 01005 to 1210
capacitance: 1pF to 100uF
Voltage: 4V to 630V |
|
| Electrolytic supplier of capacitors for electronics from NIC Components include Aluminum Electrolytic Capacitors and Tantalum Electrolytic Capacitors available in surface mount and leaded mounting types. |
|
| Leaded electroltic capacitor suppliers for electronics are available in Radial Leaded, Snap-In, and Screw-In terminal variations. |
|
AVX offers excellent cost versus performance options for low ESR tantalum and niobium oxide* industrial capacitors. Single and multi-anode devices ensure design engineers can specify the best solution in their circuits with very low ESR performance in all TPS, TPM, NOS and NPM versions.
If you have any specific requirements, please contact your local AVX sales office for details on how AVX Low ESR Capacitors can assist you in addressing your future requirements.
TPS http://www.avx.com/docs/catalogs/tps.pdf
TPM http://www.avx.com/docs/catalogs/tpm.pdf
NOS http://www.avx.com/docs/catalogs/nos.pdf
NOM http://www.avx.com/docs/catalogs/nom.pdf
*Niobium oxide capacitors are made under license form Cabot Corporation
|
|
Chip mica capacitors
UC Series [RoHS Compliant]
Chip Mica Capacitors of high accuracy for high frequency.
Small temperature coefficent and suitable to high withstand voltage.
Sample kits of chip mica capacitors
Designers' kit of chip mica capacitors of exellent electrical performance
|
|
SMT ALUMINUM ELECTROLYTIC CAPACITORS MANUFACTURER:
- Readily available with steady shorter lead times.
- Less expensive
- Higher safety margin (improved tolerance to transient events and reserve biasing conditions).
SMT CERAMIC INTEGRATED CIRCUIT CAPACITORS:
- Readily available with steady shorter lead times.
- Less expensive (low CV combinations)
- Non-Polarized (immune to unforeseen reserve biasing/ transient conditions) |
|
Technical Data
1. Dielectric: Polypropylene film.
2. Encapsulation: Flame-retardent plastic case, UL 94 V-0,
3. With suppliers of epoxy resin industrial seal: Black.
4. Temperature range: 25°C to 100°C
5. Capacitance range: 0.1 ~ 4.7µF.
6. Rated working voltage range: 1000V, 1200V, 1600V DC
7. Test category: 25/100/21 in accordance with IEC
8. DAMP-HEAT TEST: Capacitor supplier are subjected to an environmental test chamber at R.H. 90 to 95 %, operating temperatures for 240 hours.
After the test, capacitor shall be conditioned at room temperature for 2 hours and meet the following criteria
( A ) Capacitance change shall be less than 3 %.
( B ) Dissipation factor shall be less than 0.2 %.
( C ) Insulation resistance shall be over 50 % of the minimum requirement.
9. Insulation resistance ( IR ) at 25°C: Measurement shall be mad at 25°C after applyingfor 60 Sec, at 1000VDC, Above 20,000 F.
10. Dissipations factors at 25°C (tan ): 0.1 % MAX. When measured at 1 KHZ.
11. Capacitance tolerances: ± 5 %.
12. Test voltage: 2.5 Ur, 2 sec.
13. PULL TEST: Will sustain 2 Kg steady pull in the direction of lead egress and 1 Kg steady pull at any 90 degree angle for 60 seconds. After test, capacitor shall show no evidence of damage and pass all electrical requirements.
|
|
For high volume tantalum and niobium oxide capacitors manufacturers with leading edge technology call us first - AVX your global partner.
The amount of capacitance possible in a tantalum capacitor is directly related to the type of tantalum powder used to manufacture the anode. Powder improvements have been achieved through close development with the material suppliers. AVX Tantalum is committed to driving the available technology forward as is clearly demonstrated by extended ratings continually being developed, and new technologies such as TACmicrochip® and OxiCap® technology.
If you have any specific requirements, please contact your local AVX sales office for details on how AVX Tantalum can assist you in addressing your future requirements. www.avx.com
|
|
The market orientation of the company is dedicated to establishing and maintaining close contacts with business partners. In addition to standardised products and services, Iskra Kondenzatorji d.d. prides itself on its ability to adapt to the customer's technical (electrical and mechanical) parameters and specific requirements (Custom Design), continually striving to bring our products in line with the European and international standards. Quality of products is the guiding principle of Iskra Kondenzatorji.
Our products are sold in over 40 countries worldwide. |
|
| ATC provides low cost general purpose industrial capacitors not intended for precision designs, but suitable for many applications including DC blocking, coupling, bypassing and filtering. |
|
Metallized polyester capacitors suppliers
Metallized polypropylen capacitors
Polypropylen capacitors
Polyester capacitors |
|
This series of metallized polypropylene film / Polypropylene Film Foil capacitor suppliers is for higher discharge current ( Ipeak and Irms ) and surge voltage application.
Capacitance range : 0.001uF to 5uF
Voltage range : 160Vdc to 2000Vdc / 100Vac to 600Vac
Catalogue can be download in our website. http://www.filmcapacitor-st.com
Prompt Delivery, worldwide !
For further details and quotation please contact us : info@filmcapacitor-st.com |
|
| Especially designed for inductive heat generating plants operating at frequencies between 50 and 1000 Hz. |
|
| for power-factor correction of inductive consumers (transformers, electrical motors, rectifiers) in industrial networks for voltages of up to 660 V |
|
Most of our capacitors suppliers can be modified according to customer's application and circuitry - electrically and mechanically, size, electrical connection and capacitor installation.
This way customers can have most benefit from our capacitors, not just price but electrically and mechanically etc...
Most of these capacitors can withstand higher frequency, voltage and discharge current circuitry application.
Power Film capacitor
High Voltage Film Capacitor
Pulse Grade Capacitor
Pulse Capacitor
Snubber Capacitor
RC Snubber
Professional filter Capacitor
Feed Thru Capacitor
Lighting Capacitor
Motor Run Capacitor : Cylindrical type
Capacitors Network
Axial Lead Film Capacitor
Polypropylene Capacitor
Film Foil Capacitor
Brazing Capacitor
Professional furnace Capacitor
Catalogue can be download in our website. http://www.filmcapacitor-st.com
We even support small quantity order.
Prompt Delivery, worldwide !
For further details and quotation please contact us : info@filmcapacitor-st.com
|
|
Snubber Capacitor manufacturers – Axial Leads
Application :
- Protecting Thyristor against transient voltage and current
- Applications where high dv/dt is encountered
STP-01QE Electrical wires + Terminals options for easier installation
STP-01Q Tin-plated copper lead wires - PCB soldering
Capacitance : 0.01uF ~ 4.7uF at 1kHz +25C
Capacitance Tolerance : ±5%(J), ±10% (K)
Catalogue can be download in our website. http://www.filmcapacitor-st.com
Prompt Delivery, worldwide !
For details, please contact info@filmcapacitor-st.com
|
|
It is designed to
- handle high peak pulse current
- ( Gate turn-off Thyristor ) GTO Snubber / Commutation protection
- Motor Control and Static Drive application
- With build-in M6 / M8 thread stub for easy connection
Catalogue can be download in our website. http://www.filmcapacitor-st.com
We even support small quantity order.
Prompt Delivery, worldwide !
For further details and quotation please contact us : info@filmcapacitor-st.com |
|
Protect IGBT modules against voltage and current transients and applications where high dv/dt is encountered.
Voltage Range : 1000Vdc - 2000Vdc / 500Vac - 650Vac
Capacitance Range : 0.1uF - 2.2uF
very Low ESR and self-Inductance
High rms Current
Construction :
- Extended double sided metallized carrier film design with internal series connection and metallized film construction
- Direct Mount IGBT
Catalogue can be download in our website. http://www.filmcapacitor-st.com
We support small quantity order.
Prompt Delivery, worldwide !
For further details and quotation please contact us : info@filmcapacitor-st.com
|
|
This series of capacitor suppliers is for SCR Thyristor Snubbering and Commutation.
- Plastic Case with Epoxy resin supplier - dry construction
- Voltage range : 500Vac ~ 1350Vac / 900V ~ 2300Vdc
- Capacitance : 0.1uF ~ 50uF
- Electrical Connection : M4, M6, M8 Bolt suppliers or Tab Terminals
- with M8 Bolt threads at capacitor bottom for capactior installation
Catalogue can be download in our website. http://www.filmcapacitor-st.com
We even support small quantity order.
Prompt Delivery, worldwide !
For details, please contact info@filmcapacitor-st.com |
|
|
|
