|
|
Features
With simpIe structure,easy dismount,adjustabIe foot height,vibration-proof device,Iow noises,high efficiency,Iong-term normal operation,easy maintenance,gentle and tender treatment, of materiaIs this sanitary centrifugaI pump series is your ideaI choice.It complies with food sanitary standard and guarantees original taste of your products.
Application
Mainly used in industries such as pharmacy,aIcohol,foodstuff chemicaI and beverage to deliver Iiquid in smaII flow with high pressure and high pressure filtering.
|
|
Magnetically coupled centrifugal pumps of building group 1 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Constructional design
Housing, impeller, impeller magnet coating and rear casing are made of either glass-fibre reinforced PP plastic or PVDF or stainless steel. Sleeve bearings, starting ring and centering shaft are made of 99.7% pure oxide ceramic. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
Magnetically coupled centrifugal pumps of building group 2 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Housing, impeller, impeller magnet coating and rear casing can be made of either glass-fibre reinforced PP plastic or PVDF. Sleeve bearings, starting ring and centering shaft are made of 99.7% pure oxide ceramic. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
- With non-ventilated motor so that it is insensitive to vapour.
|
|
Magnetically coupled centrifugal pumps of building group 4.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.
Housing, impeller, impeller magnet coating and rear casing can be made of either glass-fibre reinforced PP plastic or PVDF. Sleeve bearings, starting rings and centering shaft are made of 99.7% pure oxide ceramic. The impeller starting ring is made of PTFE graphite. O-ring sealing of the housing is made of FPM or EPDM or FEP (optionally available).
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
|
|
|
|
The centrifugal immersion pumps of building group 4 are used for wet-pit operation in containers, pits and tanks. Centrifugal immersion pumps for dry-well installation, i.e. to be installed and operated outside the container, are also available.
All components of pumps in plastic design that are in contact with the fluid are made of PP or PVDF. The pump shaft consists of a motor shaft made of stainless steel and a shaft-protecting tube of either PP or PVDF. Built-in elastomers are made of FPM (or also EPDM without surcharge). Centrifugal immersion pumps are equipped with overhang shafts so that there is no need to provide for shaft bearings in components that are in contact with the fluid. Thus, the pumps are safe to run dry and do not require regular service and maintenance.
There is no need of a mechanical sealing of the shaft. Only a so-called gas seal is installed beneath the motor to prevent aggressive vapours from penetrating the motor chamber. But this seal is never in contact with the fluid delivered.
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
Vertical centrifugal immersion pumps
Seal lots and safe to run dry Solid plastic vertical centrifugal immersion pumps are used predominantly space-saving by direct installation into industrial environments. For strongly crystallizing media, centrifugal immersion Pumps are supplied with a special seal to avoid the penetration of steam and the connected crystallization. Standard depths of immersion are ranging from 200 mm up to 500 mm. Depths of immersion up to 1000 mm are possible by the means of an intermediate bearing
Fluids delivered:
- Acids, bases and mixtures
- Solvents
- Alkaline degreasing baths
- Electroplating baths
- Foto chemicals
- Radioactive, aseptic and precious liquids
- Food stuffs
- Other low-viscosity fluids
Fields of application:
- Electroplating
- Etching and cleaning plants
- Refrigerating machines
- Solar systems
- Sewage and water treatment
- Foto industry
- Textile and food industries, etc.
|
|
Features and Applications
The EZG(S) series Slurry Pump is a type of large capacity, high head slurry pump which is ideally suited to remove ash & sludge and to deliver liquid-solids mixture. It can be installed in multistage series. It has wide passage, non-clogging and good performance of NPSH. Expeller seal combined with packing seal or mechanical seal is adopted to guarantee the low leakage of slurry. This series has ideal structure, high efficiency, long service life, high reliability, easy maintenance, and low cost of running.
The pump can be used for seawater ash-removing to prevent it from corrosion of seawater, salt and mist, and electrochemical corrosion. It is widely used for handling abrasive and corrosive slurry in electric power, metallurgy, mine, coal, construction material and chemical industry departments, especially for removing ash and sludge in electric power station.
Notation
EZG(S)-65
E:Excellence
Z:Slurry
G:High head
S:Run in series
65:Discharge size (mm)
|
|
|
|
|
|
Introduction:
With the development of the technology, our company has introduced the series EZJ slurry pump under the theory of modern fluid mechanics and mechanical, based on the software design and practical experiences.
The EZJ series slurry pumps are designed as single-stage, single-suction centrifugal pumps.They are classified into the horizontal version (EZJ type) and vertical version (EZJL type) according to mode of construction and the discharge diameters of horizontal pumps vary from 300mm to 200mm 150mm, 100mm, 80mm, 65mm, 50mm, 40mm, etc.And the discharge diameters of vertical pumps vary from 150mm to 100mm 80mm 65mm 50mm, etc.
The pumps are innovative in both hydraulic and structural designs.The wet parts are made from self-developed high-chrome alloy cast iron with high wear-resistance.They are of energy- saving, high efficiency, little vibration, low noise, long service, lightweight, reliable operation and easy maintenance.
Application:
The EZJ series slurry pumps are widely used in power, metallurgical, mining, coal and building materials, which are suitable for handling abrasive and corrosive solids-bearing slurries with maximum concentrations of wt.45% (ash) and wt.60% (ore) such as handling the fine ore and tailings in mining, removing ash and dredges in power plant and delivering coal tailings.The pumps can be operated in series according to special requirements.
Notation:
80EZJ(V)-A42
E:Excellence
ZJ:Slurry
V:Vertical type
80: Discharge size (inch)
A:5 B:4 C:3 (the number of the vanes of the impeller)
42:The diameter of the impeller
|
|
|
|
|
|
Introduction:
The EZJ series centrifugal slurry pumps are designed as single-stage, single-suction centrifugal pumps.They are classified into the horizontal version (EZJ type) and vertical version (EZJL type) according to mode of construction and the discharge diameters of horizontal pumps vary from 300mm to 200mm 150mm, 100mm, 80mm, 65mm, 50mm, 40mm, etc.And the discharge diameters of vertical pumps vary from 150mm to 100mm 80mm 65mm 50mm, etc.
The centrifugal pumps are innovative in both hydraulic and structural designs.The wet parts are made from self-developed high-chrome alloy cast iron with high wear-resistance.They are of energy- saving, high efficiency, little vibration, low noise, long service, lightweight, reliable operation and easy maintenance.
Application:
The EZJ series centrifugal slurry pumps are widely used in power, metallurgical, mining, coal and building materials, which are suitable for handling abrasive and corrosive solids-bearing slurries with maximum concentrations of wt.45% (ash) and wt.60% (ore) such as handling the fine ore and tailings in mining, removing ash and dredges in power plant and delivering coal tailings.The centrifugal pumps can be operated in series according to special requirements.
|
|
Features and Applications
The ELM(R) series slurry pumps are cantilevered, horizontal, centrifugal, slurry pumps. They are suitable for delivering less abrasive, low dense slurry in the metallurgical, mining, coal and construction material industry. The shaft seal is adopted both gland seal and centrifugal seal.
The ELM(R) series slurry pumps have a high rate of revolution and small volume saving floor area. The frame plates have changeable, wear-resistant metal liners or rubber liners upon request and the impellers are made of wear-resistant metal or rubber. The discharge branch can be oriented to any of the eight different positions for installation and application upon request.
Notation
ELM(R)-75C
E:Excellence
L:Low concentration
M:Metal lined
R:Rubber lined
75: Discharge size (mm)
C:Frame type with maximum power
|
|
EGM Series slurry pumps are cantilevered, horizontal slurry pumps, centrifugal slurry pumps. They are designed for the handling of highly abrasive, high-density slurries. This series pump may also be installed in multistage series.
The frame plate liner and impeller for EGM Series Centrifugal slurry pump are made of wear-resistant metal. The shaft seals for the EGM series may choose gland seal or expeller seal. The discharge branch can be oriented to any of the eight positions to suit installations and applications.
This kind of centrifugal slurry pump mainly applies in the metallurgical, mining, coal, power generation, construction material and many other industries.
|
|
Features and Applications
The EZG(S) series Slurry Pump is a type of large capacity, high head slurry pump which is ideally suited to remove ash & sludge and to deliver liquid-solids mixture. It can be installed in multistage series. It has wide passage, non-clogging and good performance of NPSH. Expeller seal combined with packing seal or mechanical seal is adopted to guarantee the low leakage of slurry. This series has ideal structure, high efficiency, long service life, high reliability, easy maintenance, and low cost of running.
The pump can be used for seawater ash-removing to prevent it from corrosion of seawater, salt and mist, and electrochemical corrosion. It is widely used for handling abrasive and corrosive slurry in electric power, metallurgy, mine, coal, construction material and chemical industry departments, especially for removing ash and sludge in electric power station.
Notation
EZG(S)-65
E:Excellence
Z:Slurry
G:High head
S:Run in series
65:Discharge size (mm)
|
|
The ELM(R) series Centrifugal slurry pumps are cantilevered slurry pumps, horizontal, centrifugal slurry pumps. They are suitable for delivering less abrasive, low dense slurry. The ELM(R) series centrifugal slurry pumps have a high rate of revolution and small volume saving floor area.
The frame plates of ELM Series Centrifugal slurry pump have changeable, wear-resistant metal liners or rubber liners upon request and the impellers are made of wear-resistant metal or rubber. And the discharge branch can be oriented to any of the eight different positions for installation and application upon request. The shaft seal is adopted both gland seal and centrifugal seal.
This kind of centrifugal slurry pump mainly applies in the metallurgical, mining, coal and construction material industry etc.
Notation
ELM-150E
E:Excellence
L:Low concentration
M:Metal lined
150: Discharge size (mm)
E:Frame type with maximum power
|
|
introduction and application
EWN dredging pump is a new type of sludge pump manufactured by our company after extensive research.It is suited for condition in which the rivers and sea beds are out of service for a long time, dredging and damming are extremely urgent.After years of application in treating rivers and seas at home and abroad, dredging pump is widely recognized as the main pumping equipment.This series are considered the environmental friendly, highly efficient and energy-saving equipment.EWN pump is a single-stage, single-suction cantilevered horizontal centrifugal pump with advantages of light weight, wear-resistance and superior dredging performance.It is perfectly suited for dredging on the whole construction, high return of investment.It thoroughly meets requirements of most industrial applications.
Notation:
500 ED(G/D)
E:Excellence
D:Dredging Pump
500:Outlet Diameter of Dredging Pump (mm)
|
|
|
|
|
|
Introduction:
The EZJ series slurry pumps are designed as single-stage, single-suction centrifugal pumps.They are classified into the horizontal version (EZJ type) and vertical version (EZJL type) according to mode of construction and the discharge diameters of horizontal pumps vary from 300mm to 200mm 150mm, 100mm, 80mm, 65mm, 50mm, 40mm, etc.And the discharge diameters of vertical pumps vary from 150mm to 100mm 80mm 65mm 50mm, etc.
The centrifugal pumps are innovative in both hydraulic and structural designs.The wet parts are made from self-developed high-chrome alloy cast iron with high wear-resistance.They are of energy- saving, high efficiency, little vibration, low noise, long service, lightweight, reliable operation and easy maintenance
Application:
The EZJ series centrifugal slurry pumps are widely used in power station, metallurgical, mining, coal and building materials, which are suitable for handling abrasive and corrosive solids-bearing slurries with maximum concentrations of wt.45% (ash) and wt.60% (ore) such as handling the fine ore and tailings in mining, removing ash and dredges in power plant and delivering coal tailings.The centrifugal pumps can be operated in series according to special requirements.
Notation
200EZJ-A60
E:Excellence
ZJ:Slurry
200: Discharge size (inch)
A:5 B:4 C:3 (the number of the vanes of the impeller)
60:The diameter of the impeller.
|
|
The EHR series slurry pumps are cantilevered, horizontal, centrifugal slurry pumps. They are designed for the handling of highly abrasive, high-density slurries. The pumps of this series can be installed in multistage series.
The impellers of this kind of slurry pump are made of rubber. The frame plates for this kind of slurry pump have replaceable wear-resistant rubber liners. The discharge branch can be oriented to any of the eight different positions. The shaft seals of this kind of slurry pump may adopt shaft gland seal or expeller seal.
This kind of slurry pump mainly applies in the metallurgical, mining, coal, power, construction material and many other industries.
Notation
EHR-3D
E: Excellence
H: High concentration
R: Rubber lined
3: Discharge size (inch)
D: Frame type with maximum power
|
|
|
|
|
|
The features are as followed:
The frame plates for type EHM pumps have replaceable wear-resistant metal liners . The impellers are made of wear-resistant metal. The frame plate liner and impeller for EHM pump are adoptable of hard metal only.
Bearing assembly use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication.
The shaft seal could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices.
Wide performance, good NPSH and high efficiency. The pump of this type may be installed in multistage series to meet the delivery for long distance.
Application:
The type of EHM pumps are using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc.
For example: Coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station.
Notation:
EHM-4D
E:Excellence
H:High concentration
M:Metal lined
4: Discharge size (inch)
D: Frame type with maximum power
|
|
|
|
|
|
Introduction :
EHM Series slurry pump is mainly using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc.
The frame plates of this kind of slurry pump have replaceable wear-resistant metal liners. The impellers are made of wear-resistant metal. The frame plate liner and impeller for EHM pump are adoptable of hard metal only.
Bearing assembly of this kind of slurry pump use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication.
The shaft seal of this kind of slurry pump could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices. The pump of this type may be installed in multistage series to meet the delivery for long distance.
Application:
This kind of slurry pump mainly applies in coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station etc.
Notation:
EHM-10ST
E:Excellence
H:High concentration
M:Metal lined
10: Discharge size (inch)
ST: Frame type with maximum power
|
|
Features and Applications
The EHR series slurry pumps are cantilevered, horizontal, centrifugal slurry pumps. They are designed for the handling of highly abrasive, high density slurries in the metallurgical, mining, coal, power, construction material and many other industries. The pumps of this series can be installed in multistage series.
The frame plates for the EHM series have replaceable wear-resistant metal liners. The EHR series have replaceable wear-resistant rubber liners. The impellers are made of rubber for the EHR series. The shaft seals of the EHR series may adopt shaft gland seal or expeller seal. The discharge branch can be oriented to any of the eight different positions
Notation
EHR-4D
E: Excellence
H: High concentration
R: Rubber lined
4: Discharge size (inch)
D: Frame type with maximum power
|
|
Gorman-Rupp 60 Series pumps are standard centrifugal, high pressure, high volume pumps with exceptional efficiencies (up to 85%). Discharge on many models can be placed in any position by turning the pump casing.
Specifications
Size: 3" (75 mm), 4" (100 mm), 5" (125 mm), 6" (150 mm), 8" (200 mm), 10" (250 mm), 12" (300 mm)
Max Capacity: 6,800 GPM (429 lps)
Max Head: 500' (152 m)
Max Solids: 3" (76 mm)
Max Temperature: 160 F (71 C)
Materials of Construction: Cast Iron, Cast Steel, Ductile Iron
|
|
The Gorman-Rupp line of engine driven high pressure fire pumps delivers up to 156 PSI and 250 GPM. They are equipped with an exhaust primer. All units have a built-in check valve and include a discharge pressure gauge, brass hose adapters - NPT to National Standard Fire Hose Threads, and a suction strainer.
Specifications
Size: 1-1/2" (37.5 mm), 2-1/2" (62.5 mm)
Max Capacity: 260 GPM (16 lps)
Max Head: 360' (110 m)
Max Solids: 0.3125" (8 mm)
Materials of Construction: Aluminum
Horsepower: 13 HP to 23 HP
|
|
|
|
|
|
The features are as followed:
The frame plates for type EHM pumps have replaceable wear-resistant metal liners . The impellers are made of wear-resistant metal. The frame plate liner and impeller for EHM pump are adoptable of hard metal only.
Bearing assembly use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication.
The shaft seal could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices.
Wide performance, good NPSH and high efficiency. The pump of this type may be installed in multistage series to meet the delivery for long distance.
Application:
The type of EHM pumps are using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc.
For example: Coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station.
Notation:
EHM-6E
E:Excellence
H:High concentration
M:Metal lined
6: Discharge size (inch)
E: Frame type with maximum power
|
|
|
Whether bypassing a pump station during repair, keeping critical services operational at a plant, or helping a construction crew finish on time, Gorman-Rupp's Super T Series® portable engine-driven pumps keep the liquid flowing. Gorman-Rupp's Super T Series self-priming centrifugal pumps are designed to reprime automatically in a completely open system - without a need for suction or discharge check valves (an optional discharge check and air release valve is only required when pumping against a pressurized system). Additionally, there is no need for add-on vacuum pumps or compressors, which add to owner maintenance and increase the potential for costly repairs.
|
|
Today’s pumping applications demand better and more efficient self-priming, solids-handling pumps. At Gorman-Rupp, providing greater performance and reducing installation and maintenance costs have always been our ultimate goals. This makes the Ultra V one of the best values introduced to the pump industry in decades.
This next generation of solids-handling, self-priming centrifugal pumps offers substantially higher pressures, flows, efficiencies and time-saving maintenance features, all in one package.
Ultra V Series pumps achieve up to 60% increased pressure and 40% increased flow over traditional self-priming trash pumps of the same size, while substantially increasing overall pumping efficiency.
|
|
IH Type chemical and industry pump is mono-grade mono-absorb cantilever type centrifugal pump, which is a kind of renew energy-saving product that replaced F type cauterization –resistant pump, it is suit to chemical and industry, petroleum, foodstuff, pharmacy and synthetic fiber and etc department where transport the cauterization –resistant type medium or physical、chemical similar to water medium. This pump material is stainless steel.
high efficiency and save energy
- widely applicable
- install easy
- low noise
- structure reasonably
- international standard
- convenient maintenance
- working temperature 80℃
|
|
ALW horizontal type centrifugal clear water pump is used to transport clear water and other liquid has chemical and physical property similar with the clear water. It is applicable to water supply and drainage for industry and city pressure increasing water supply for high building ,garden irrigation, pressure increasing for fire fighting, long distance transportation, heating and cooling circulation, cold and warm water circulation pressure increasing and matching equipment, the using temperature is T ≤ 80 ℃.
- Stable function
- watertight
- low noise
- Low rate of failure
- convenient repair
- small occupying of the land
|
|
CQ TYPE magnetic force driving pump (called magnetic pump), is the new product, which use the permanent magnet join-axis working principle for centrifugal pump, and has advantage of reasonable structure, advanced workmanship, full sealed, non-leakage and cauterization-proof, its performance can be match to the same product of foreign countries.
- reasonable structure
- advanced workmanship
- full sealed, non-leakage
- strong corrosion-resistance
- compact conformation、good- looking appearance
- small in size 、low noise
- uniformity of operation
- convenient maintenance
|
|
ALG series single stage single suction pipeline centrifugal pump are designed by scientific and technical personnel of our company and domestic water pump experts, which select the domestic excellent hydraulic model, adopt the performance parameter of the centrifugal pump of Model IS. Besides, according to different using temperature and medium, we develop pumps applicable for hot water, high temperature the corrosive environment, oil transporting on the basis of Model ALG
- Suitable for industry and city's giving and draining off water
- It is convenient to form a complete set with other apparatus
- High efficiency, low noise
- There are cold water types, hot water type, high temperature type, chemical industry type, oil type
- Performance is reliable
- International standard
|
|
* 4 bearing modules.
* Horizontal flange mounted motor. (some versions utilize foot and flanged)
* Back pull out.
* Stub shaft extension.
* Separate seal cover allowing multi-choice of seal designs. (see Egger Varioseal® system)
* Compact design.
* No motor alignment necessary
|
|
Discharge
DN150 – 500 mm (6¨ - 20¨)
Capacity
Up to 1500 l/sec (23’700 US gpm)
Head
Up to 90 m (295 ft)
Application
Slurries containing fibrous material, large irregular solids Raw & Screened sewage.
|
|
|
|
