|
|
Features and Applications
The EZG(S) series Slurry Pump is a type of large capacity, high head slurry pump which is ideally suited to remove ash & sludge and to deliver liquid-solids mixture. It can be installed in multistage series. It has wide passage, non-clogging and good performance of NPSH. Expeller seal combined with packing seal or mechanical seal is adopted to guarantee the low leakage of slurry. This series has ideal structure, high efficiency, long service life, high reliability, easy maintenance, and low cost of running.
The pump can be used for seawater ash-removing to prevent it from corrosion of seawater, salt and mist, and electrochemical corrosion. It is widely used for handling abrasive and corrosive slurry in electric power, metallurgy, mine, coal, construction material and chemical industry departments, especially for removing ash and sludge in electric power station.
Notation
EZG(S)-65
E:Excellence
Z:Slurry
G:High head
S:Run in series
65:Discharge size (mm)
|
|
|
|
|
|
The features are as followed:
The frame plates for type EHM pumps have replaceable wear-resistant metal liners . The impellers are made of wear-resistant metal. The frame plate liner and impeller for EHM pump are adoptable of hard metal only.
Bearing assembly use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication.
The shaft seal could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices.
Wide performance, good NPSH and high efficiency. The pump of this type may be installed in multistage series to meet the delivery for long distance.
Application:
The type of EHM pumps are using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc.
For example: Coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station.
Notation:
EHM-4D
E:Excellence
H:High concentration
M:Metal lined
4: Discharge size (inch)
D: Frame type with maximum power
|
|
PUMPEX sludge pump SK is a portable pump and
features a sturdy stainless steel handle and a robust
ductile iron stand.
It can easily be lifted and moved to where it is needed
without suction hoses or any concern about suction lifts.
This makes installation and operation easy and safe.
|
|
Features and Applications
The EHR series slurry pumps are cantilevered, horizontal, centrifugal slurry pumps. They are designed for the handling of highly abrasive, high density slurries in the metallurgical, mining, coal, power, construction material and many other industries. The pumps of this series can be installed in multistage series.
The frame plates for the EHM series have replaceable wear-resistant metal liners. The EHR series have replaceable wear-resistant rubber liners. The impellers are made of rubber for the EHR series. The shaft seals of the EHR series may adopt shaft gland seal or expeller seal. The discharge branch can be oriented to any of the eight different positions
Notation
EHR-4D
E: Excellence
H: High concentration
R: Rubber lined
4: Discharge size (inch)
D: Frame type with maximum power
|
|
The centrifugal self-priming pumps DELTA have an open impeller suitable for the passage of solids in suspension in the liquid to be pumped. The pump casing is in high-resistance cast iron.
The mechanical seal is in tungsten carbide and does not require maintenance.
The pump is monobloc without belts, pulleys, bearings or other metallic parts in contact.
|
|
Slurry Pumps
Krebs millMAX severe-duty slurry pumps have a unique design developed exclusively for grinding mill discharge duties and other abrasive slurries. FLSmidth Krebs offers wet end conversions or complete pump assemblies to meet customer desires and demands.
The millMAX Pump features a patented on-line wear clearance adjustment, which minimizes cost per ton pumped compared to conventional hard metal and rubber lined pumps through:
- Increased Wear Life
- Lower Power Consumption
- On-line Wear Clearance Adjustment
- Increased Mill Throughput
- More Consistent Hydrocyclone Separation
- Less Downtime
|
|
|
|
|
|
Horizontal single stage centrifugal pumps with over hung impeller and axial suction, constructed using the "Back pull-out system" .
The pumps function by making use of the induced vortex principle: the impeller, which is positioned further back than the pump body, because of its particular shape induces a vortex in the conveyed liquid which expands in the body creating the pump discharge head.
Advantages
- The open impeller, which is positioned further back, with wide inter-vane passages makes it possible to convey, without any danger of blockages, dirty or viscous liquids, liquids containing particles in suspension or with fibrous impurities, chemically inert or aggressive liquids and those with dissolved air and solutions with crystals in suspension
- High performance levels
- Reliability
- Compactness
Fields of application
Because of their operating characteristics , the RKN and RKC pumps are particularly suited for use in the following plants:
- The paper and chemical wood pulp industries
- The sugar industry
- The farm-food industry
- The textile industry
- Waste water and sewage treatment plants
- The construction sector
- The chemical and petrochemical industry
- The pharmaceutical industry
- Thermo-electric power stations
|
|
Elastomer Lined Slurry pumps available in close coupled and XT models featuring extra thick liners. Elastomers available include rubber, neoprene and ceramic rod media for severe duty.
Specifications:
Capacities up to 20,000 GPM (4542 m3/h)
Heads to 164 feet (50 m)
Temperatures to 250° F (121° C)
Pressures to 400 PSIG (2758 kPa)
Solids to 1/8"(3mm)
Design Features:
Field Replaceable Rubber Liners Bolt in for quicker replacement, extra thick for extended wear life
Large Diameter Impeller for lower operating speeds, longer wear life
Five Discharge Positions suitable for most discharge pipe arrangements
Oil Lubricated Bearings for maximum bearing life.
Sealing Flexibility Choice of packing arrangements, mechanical seals.
|
|
Goulds Model 5500 is the result of many years of experience designing and building severe duty slurry pumps. It's not only built to stand up to the toughest abrasive slurry services, but also is designed for extreme ease of maintenance and safety. A heavy duty bearing frame and shaft, extra thick wall sections and easily replaceable wear parts add up to many years of service even under the severest operating conditions. Also available as 5500HP.
Specifications:
Capacities to 17000 GPM (3861 m3/h)
Heads to 425 feet (139m)
Temperatures to 250° F (121° C)
Pressures to 500 PSIG (3448 kPa)
Solids to 5 inches (127 mm)
|
|
General description
Wilfley's Model K solids-handling centrifugal pump is designed for abrasive solids applications such as those found in aggregate, cement, lime slurries and many other common industrial and mining applications.
Markets
- Cement, sand & gravel, fines recovery systems
- Industrial minerals: potash, kaolin clays, sodium carbonate, titanium dioxide
- Mineral processing: copper, iron ore, lead/zinc
- Waste water: grit, lime, pH control
Applications
- Cyclone and screen feed
- Cement kiln feed and transfer applications
- Thickener under/over flow
- Tailings
- Transfer applications
- Loading/unloading applications
Capacities
- Size ranges from 2x1 to 14x10, from less than 50 GPM/2.2 m3/hr up to 6,000 GPM/910 m3/hr. Head capabilities ranging up to 200 ft/90 meters depending upon pump size.
|
|
General description
Wilfley's Model S3 centrifugal pump is designed and constructed for handling difficult combinations of corrosive liquids and abrasive solids.
Markets
- Fertilizer production: phosphoric acid
- Industrial minerals: potash, kaolin clays, titanium dioxide
- Mining
- Power
Applications
- Ash handling
- Cyclone feed
- Thickener under/over flow
- Tailings
- Loading/unloading applications
Capacities
Sizes from 3x2-11, 4x3-11, 6x4-13 and 6x4-16 offer an operating range coverage of approximately 100 GPM/22 m3/hr up to 1,200 GPM/275 m3/hr. Head capabilities ranging up to 250 ft/75 meters depending upon the model size.
|
|
|
|
|
|
ITT Flygt NSW (Produced in Pewaukee USA)
Technical features:
Design: centrifugal radial flow
Type of impeller: closed non clog design
Motor: Customer choice B3 or V1/ IP 55
Size of outlet flange: DN 100 – DN 300
Max. liquid temperature: 120°C
Max. Flow: 2.000 m3/h
Pump sealing: Double Mech. seal or packing or Chesterton split seal
Max. Head: 80 m
Solids up to 162 mm
Max. operating pressure: 10 bar
Shaft sleeve Impeller Pump Housing Pump seal
AISI 4140 Ductile iron Cast iron Teflon + Acrylic yarn
Option: 3% Ni-cast 3% Ni-cast Customer choice
ITT Flygt NSY (Produced in Pewaukee USA)
Technical features:
Design: centrifugal radial flow
Motor: Customer choice B3 or V1/ IP 55
Type of impeller: closed non clog design
Size of outlet flange: DN 250 – DN 600
Max. liquid temperature: 315°C
Max. Flow: 5.000 m3/h
Pump sealing: Double Mech. seal or packing or Chesterton split seal
Max. Head: 25 m
Solids up to 229 mm
Max. operating pressure: 10 bar
Shaft sleeve Impeller Pump Housing Pump seal
AISI 4140 Ductile iron Cast iron Teflon + Acrylic yarn Option: 3% Ni-cast 3% Ni-cast Customer choice
|
|
Type SM waste water pump with auto-matic suctioning:
From Schmalenberger’s industrial pump range. The pump is designed for media containing a high level of trapped air, along with media with coarse or excessive contamination and solid matter admix.
Applications:
Chemically-neutral media, such as lye, solvents, coolants, lubricants.
Areas of use:
Draining vats, containers, machine beds
|
|
TB-200X4T
Breezy Bud, Inc. has devoted itself since its founding to manufacturing high quality industrial blowers and fans. Our customers appreciate our dedication to working with them to produce a blower that meets their requirements.
Our blowers are engineered to run continuously trouble-free. Our blowers have a number of features that contribute to our blower's efficiency and long operating life. Some of these features include high quality materials expertly assembled, ease-of-maintenance, low vibration, and low noise operation. Listed below are some of the types of blowers that we manufacture:
-Casting Multi-Stage Centrifugal Blower
-Casting Single-Stage Centrifugal Blower
-Clean Room Fan
-Conveyor Blower
-Corrosion Resistance Blower (Titanium, Hastelloy, etc)
-Cutter and Trim Blower
-Gas-Tight Booster (1~15kg/cm2G, depend on system required.)
-Gas-Tight Blower
-High Temperature Resistance Blower 900℃
-Spark Resistance Blower
-Wear Resistance Blower
|
|
March Series 8 totally enclosed pumps, with standard wetted parts of glass-filled polypropylene, carbon-filled Kynar® and 316 stainless steel, are the ideal choice for handling difficult liquids, such as strong halogen or chromic, and sulfuric acid solutions. Typical applications range from computer cooling systems and waste treatment plants to plating operations, photo processors and chemical plants.
Flow rates range from 25 GPM (90 LPM) minimum to 125 GPM (400 LPM) maximum at heads from 0 ft. to 95 ft. (20m) maximum.
|
|
The new standard in dewatering pump technology is here: the 2600 series from Flygt. Designed to meet the increasingly stringent performance and economy demands of today’s industry, these pumps deliver unmatched wear resistance and consistent performance over time. Backed by Flygt’s outstanding support and worldwide presence, the 2600 series keeps your operations moving.
The six pumps in the range cover almost any application for work sites of every size, including construction sites, mines, and other tough environments. Output ranges from 0.75-18 kW/1.2 – 27 hp. All models feature cutting-edge design with new materials, and the patented Dura-Spin hydraulic system
|
|
Pump for abrasive slurries
ITT Flygt H 8000 available in Atex Ex de II B
Technical features:
Type of hydraulic: centrifugal radial flow
Motor: IP 68 insulated acc. class H
Type of impeller: Vortex
Motor protection: 3 thermal switches
Open throughlet: 75-150 mm
Max. liquid temperature: 70°C
Size of outlet flange: DN75 – DN150
Motor sealing: 2 mechanical seals
Max. Flow: 430 m3/h
Max. Head: 32 m
Materials:
Stator housing Impeller Pump Housing Outer seal
GG 25 Ni-Hard 4 Ni-hard 4 RSIC/RSIC
The pumps are permanently installed in horizontal or vertical position.
|
|
|
Honda trash pumps are designed to allow solids(sticks, stones, and debris) up to 13/16 inch for the 2 inch model and 1 1/16 inch for 3 and 4 inch models to flow through the pump without clogging, making them ideal for construction sites. The WT pumps are designed to move water, and lots of it. The WT40 will move water at a rate of 433 gallons per minute and is capable of handling solids without clogging. A quick clean out port and easy maintenance features ensure long service life. Honda Trash Pumps are the ultimate choice for contractors and rental applications.
|
|
|
Honda trash pumps are designed to allow solids(sticks, stones, and debris) up to 13/16 inch for the 2 inch model and 1 1/16 inch for 3 and 4 inch models to flow through the pump without clogging, making them ideal for construction sites. The WT pumps are designed to move water, and lots of it. The WT40 will move water at a rate of 433 gallons per minute and is capable of handling solids without clogging. A quick clean out port and easy maintenance features ensure long service life. Honda Trash Pumps are the ultimate choice for contractors and rental applications.
|
|
| ... products without technical information |
| |
Features and Applications
The EVM(R) series pumps are vertical, centrifugal slurry pumps submerged in sump during operation. They are designed for delivering highly abrasive, large particles and high density slurries. These pumps have no need of any shaft seal and sealing water. The pump casing of type EVM pumps are made of wear-resistant metal. The wear parts are made of high chromium for the EVM series and are rubber lined for the EVR series.
The submersible pumps are suited for handling abrasive or corrosive, dense slurry with large particle size.
Notation
EVM(R)-65Q
E:Excellence
V:Vertical type
M:Metal lined
R:Rubber lined
65:Discharge size (mm)
Q:Frame type with maximum power
|
|
Warman 5000
Metal and elastomer high head vertical slurry pumps
Features / Benefits
- Cantilevered shaft design
- Double suction, semi-open impeller
- Elastomer or abrasion resistant metal construction
- Agitator option keeps solids in suspension
- Optional suction extension
- Universal motor bracket accomodates several motor sizes
- Dual casing balances radial loads on shaft and bearings
|
|
Moyno Vertical Pumps
The new Moyno® Vertical Pump takes progressing cavity performance to new heights. It can be flange mounted to closed tanks or affixed to mounting beams above open tanks. With its inlet submerged, the pump pulls fluid from the bottom of the storage vessel and discharges it at the surface for further processing downstream.
|
|
NL type sewage and slurry pump
- widely applicable
- can be used for draining flooded fields and fighting droughts
- durable、wearproof
- pleasing shape
- convenient maintenance
- as simple ambulatory fire fighting pumps in the village
- widely applicable
- safe and reliable
|
|
ITT Flygt WC & YDD (Pewaukee US)
Technical features:
Design: Vertical turbine “pull out”
Size of outlet flange: according demand
Max. liquid temperature: according demand
Max. Flow: 90.000 m3/h
Pump sealing: Mech. seal or packing.
Max. Head: 25 m
Max. operating pressure: 10 bar
Shaft Impeller Column Pump seal
AISI 410 AISI 316 GG 25 Customer choice
Duplex Duplex or Super Duplex
ITT Vogel WM (Peewaukee US)
Technical features:
Design: Vertical turbine
Type of impeller: enclosed
Max. Flow: 60.000 m3/h
Max. Head: 175 m
Max. operating pressure: 25 bar
Shaft Impeller Column Pump seal
AISI 410 AISI 316 GG 25 Customer choice
Duplex Duplex Duplex
Super Duplex Super Duplex Super Duplex
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
