|
|
|
We have decades of experience in the pumping of cooling water (seawater and brackish water) and engine water. We have developed our centrifugal pumps in collaboration with all notable manufacturers of diesel and marine-diesel engines. The pumps are driven via a belt or directly through a driving pinion. The pumps can be supplied with either clockwise or anticlockwise directions of rotation. Prior to starting the pumps must be filled up completely with water. In case of long periods of disuse this water should be drained via the attached draining cocks. In commercial, industrial, official or private ships and boats, e.g. fishing boats, ferries, passenger boats, yachts, tugs and working boats, pilot boats, customs and police craft, fireboats and rescue cruisers, boats of the federal navy and of the federal border patrol.
|
|
APPLICATIONS
* FOR DOMESTIC SYSTEMS AND SMALL IRRIGATION SYSTEM
PRESSURISATION.
* HANDLING OF NON AGGRESSIVE CIVIL AND INDUSTRIAL LIQUIDS.
* FOR WASHING SYSTEMS AND FOR INSERTION INTO COMPLEX
INDUSTRIAL MACHINERY AND LINES.
DESIGN ENGINEERING
* SEALED MOTOR WITH EXTERNAL VENTILATION AND FINNED ALUMINIUM
ALLOY CASING
* IP 44 PROTECTION CLASS
* CLASS “F” INSULATION
* MAX PUMP LIQUID TEMPERATURE: 50°
|
|
Horizontal single stage centrifugal pumps with overhung impeller and axial suction, constructed using the "Back pull-out system" and available with four different sizes of support.
Main technical features
- Flow rate up to 500 m3/h
- Discharge head up to 95 m
- Working pressure up to 10 bar
- Working temperature up to 90°C
- Environmental temperature up to 40°C
- Size from 80 to 300 mm
- Height of suction up to 7 m
- Flanges drilling UNI PN10
- Nominal rotational velocity (50Hz): 2900 rpm/1450 rpm
Advantages
- Reliability
- Long duration
|
|
|
Centrifugal single impeller low head water pumps for flow irrigation systems with high flow rates. Suitable to pump clean water or non-aggressive liquids charged with small solid impurities. To be used in flow irrigation systems in gardening and agriculture and in industrial fittings.
|
|
ELEPUMP DIESEL
The Elepump is also available with a diesel engine, offering better fuel efficiency and lower overall operating cost. Based on customer feedback, the Diesel Elepump offers better overall operating efficiency.
Designed for simple maintenance, Elepump requires only periodic oil checks and changes - and worn parts can be replaced quickly and simply without special tools.
* 45 gallons per minute pumping capacity for large drill site operations that demand greater throughput
* Mounted on 4-cylinder Kubota V1305-40M transmission Offers 30 horse power at 3000 rpm
* Newage 40M 4-speed transmission with integral reduction, providing ratios of approximately 13:1, 9:1, 5:1 and 3:1
* Factory-specified completion kits include a 12V starter and charger, radiator-cooler with HD guard, HD dry-type air cleaner, keystart with glowplug assist, Vernier-type throttle control, a battery rack and cables, Racor fuel filter, electric fuel pump and chain-type coupling
* Battery not included
|
|
|
|
|
|
ITT Flygt NSW (Produced in Pewaukee USA)
Technical features:
Design: centrifugal radial flow
Type of impeller: closed non clog design
Motor: Customer choice B3 or V1/ IP 55
Size of outlet flange: DN 100 – DN 300
Max. liquid temperature: 120°C
Max. Flow: 2.000 m3/h
Pump sealing: Double Mech. seal or packing or Chesterton split seal
Max. Head: 80 m
Solids up to 162 mm
Max. operating pressure: 10 bar
Shaft sleeve Impeller Pump Housing Pump seal
AISI 4140 Ductile iron Cast iron Teflon + Acrylic yarn
Option: 3% Ni-cast 3% Ni-cast Customer choice
ITT Flygt NSY (Produced in Pewaukee USA)
Technical features:
Design: centrifugal radial flow
Motor: Customer choice B3 or V1/ IP 55
Type of impeller: closed non clog design
Size of outlet flange: DN 250 – DN 600
Max. liquid temperature: 315°C
Max. Flow: 5.000 m3/h
Pump sealing: Double Mech. seal or packing or Chesterton split seal
Max. Head: 25 m
Solids up to 229 mm
Max. operating pressure: 10 bar
Shaft sleeve Impeller Pump Housing Pump seal
AISI 4140 Ductile iron Cast iron Teflon + Acrylic yarn Option: 3% Ni-cast 3% Ni-cast Customer choice
|
|
Type SM waste water pump with auto-matic suctioning:
From Schmalenberger’s industrial pump range. The pump is designed for media containing a high level of trapped air, along with media with coarse or excessive contamination and solid matter admix.
Applications:
Chemically-neutral media, such as lye, solvents, coolants, lubricants.
Areas of use:
Draining vats, containers, machine beds
|
|
TB-200X4T
Breezy Bud, Inc. has devoted itself since its founding to manufacturing high quality industrial blowers and fans. Our customers appreciate our dedication to working with them to produce a blower that meets their requirements.
Our blowers are engineered to run continuously trouble-free. Our blowers have a number of features that contribute to our blower's efficiency and long operating life. Some of these features include high quality materials expertly assembled, ease-of-maintenance, low vibration, and low noise operation. Listed below are some of the types of blowers that we manufacture:
-Casting Multi-Stage Centrifugal Blower
-Casting Single-Stage Centrifugal Blower
-Clean Room Fan
-Conveyor Blower
-Corrosion Resistance Blower (Titanium, Hastelloy, etc)
-Cutter and Trim Blower
-Gas-Tight Booster (1~15kg/cm2G, depend on system required.)
-Gas-Tight Blower
-High Temperature Resistance Blower 900℃
-Spark Resistance Blower
-Wear Resistance Blower
|
|
Seal-Less Brushless Water Circulating Pumps...
offer basic pump/motor designs from 12 GPM to 26 GPM in either 12 VDC or 24 VDC motor designs. Variable speed is available for the 12 GPM pump. The seal-less pump design is magnetically coupled which provides for a leak-proof pump. There are no rotating wet seals to wear out and leak. Detailed pump information is provided on the individual product sheets. AMETEK seal-less pumps are not designed for, and should not be used in, life sustaining applications.
|
|
March Series 8 totally enclosed pumps, with standard wetted parts of glass-filled polypropylene, carbon-filled Kynar® and 316 stainless steel, are the ideal choice for handling difficult liquids, such as strong halogen or chromic, and sulfuric acid solutions. Typical applications range from computer cooling systems and waste treatment plants to plating operations, photo processors and chemical plants.
Flow rates range from 25 GPM (90 LPM) minimum to 125 GPM (400 LPM) maximum at heads from 0 ft. to 95 ft. (20m) maximum.
|
|
|
Honda trash pumps are designed to allow solids(sticks, stones, and debris) up to 13/16 inch for the 2 inch model and 1 1/16 inch for 3 and 4 inch models to flow through the pump without clogging, making them ideal for construction sites. The WT pumps are designed to move water, and lots of it. The WT40 will move water at a rate of 433 gallons per minute and is capable of handling solids without clogging. A quick clean out port and easy maintenance features ensure long service life. Honda Trash Pumps are the ultimate choice for contractors and rental applications.
|
|
|
Honda trash pumps are designed to allow solids(sticks, stones, and debris) up to 13/16 inch for the 2 inch model and 1 1/16 inch for 3 and 4 inch models to flow through the pump without clogging, making them ideal for construction sites. The WT pumps are designed to move water, and lots of it. The WT40 will move water at a rate of 433 gallons per minute and is capable of handling solids without clogging. A quick clean out port and easy maintenance features ensure long service life. Honda Trash Pumps are the ultimate choice for contractors and rental applications.
|
|
The new standard in dewatering pump technology is here: the 2600 series from Flygt. Designed to meet the increasingly stringent performance and economy demands of today’s industry, these pumps deliver unmatched wear resistance and consistent performance over time. Backed by Flygt’s outstanding support and worldwide presence, the 2600 series keeps your operations moving.
The six pumps in the range cover almost any application for work sites of every size, including construction sites, mines, and other tough environments. Output ranges from 0.75-18 kW/1.2 – 27 hp. All models feature cutting-edge design with new materials, and the patented Dura-Spin hydraulic system
|
|
Pump for abrasive slurries
ITT Flygt H 8000 available in Atex Ex de II B
Technical features:
Type of hydraulic: centrifugal radial flow
Motor: IP 68 insulated acc. class H
Type of impeller: Vortex
Motor protection: 3 thermal switches
Open throughlet: 75-150 mm
Max. liquid temperature: 70°C
Size of outlet flange: DN75 – DN150
Motor sealing: 2 mechanical seals
Max. Flow: 430 m3/h
Max. Head: 32 m
Materials:
Stator housing Impeller Pump Housing Outer seal
GG 25 Ni-Hard 4 Ni-hard 4 RSIC/RSIC
The pumps are permanently installed in horizontal or vertical position.
|
|
High-pressure multi-stage centrifugal pumps and membrane element housings from GE Water & Process Technologies are more than durable components. They are precision-engineered elements that play a critical role in customers' treatment systems.
Our ruggedly built multi-stage pumps meet your requirements for general water applications, high-temperature performance, chemical compatibility, or quiet operation. Because our pumps set industry standards for reliability and low overall lifecycle costs, you can let them work without having to worry. GE's world-class pumps come with stainless steel shells on every pump and options for NorylTM impellers or stainless steel impellers.
|
|
| ... products without technical information |
| |
RD5 Series
Rotary diaphragm pump
An eccentrically mounted bearing on the shaft, rotates within a flexible diaphragm. As the shaft rotates, the bearing flexes the diaphragm, squeezing the liquid through the pump.
|
|
Features::
• Compact Design Measuring 6.4" (162 mm) in Length
• Fully Automatic Demand Pump
• Self-priming and Can Operate Dry Without Damage
• Built-in Thermal Protector
• Sealed Pressure Switch and Motor
• Flow Rates to 1.0 GPM (3.8 L/min.) and Operating Pressures to 25 PSI (1.7 bar)
• Compact automatic demand pump.
• Sealed pressure switch automaticatly starts and stops pump when discharge valve is opened and closed.
• Self-prlming so pump can be located above supply tank.
• Can run dry for extended periods of time without damage.
• Built-in thermal protector
• Low amp draw for battery powered applications.
• Soft compliant Santoprene mounting system.
|
|
|
|
see the results for the following category : 
