|
|
Technical info
Alloy : AISI 302 stainless steel
Properties :
Excellent combination of high stength with outstanding flexibility .
Applications :
Fine stainless cord is an ideal reinforcemnet in a number of elastomeric products such as tie strings,
air springs, membranes and tube connectors. Needless to say that the cords also can be used as
such, without being incorporated in a matrix .
Automotive applications: window elevator, mirror cable, control cable, fuel tank release,
parking brake .
|
|
Characteristics of the product
Heights: 8 to 40 mm (according to product) Widths: 20 to 56 mm (according to product)
Rails C asymmetrical and omega 35 mm for modular fixing of equipment.
These rails deliverable are perforated or not
Surface treatment: Rough untreated, électrozingué dichromate yellow or blue, hot galvanized Sendzimir 275 or hot galvanized with soaked.
Perforations special and put at length on request.
A range supplements clamps of fixing of cables or tubes with a diameter 6 mm to 110 mm out of steel galvanized hot with soaked, aluminum and stainless steel AISI 304 H adapted to the shaped rails and other
|
|
Turnbuckles
Reference: TE.1-36.2
Weight: 18
Dimensions: 1350 - 950
Material: Forged steel
BL: 36
S.W.L.: 18
Finished: Galvanized
Counter Parts : Bars
|
|
• Telescope action jacks; for corner routes
• Suitable for laying lines of cable
• For pit cable inlets or outlets.
• For laying cables over ducts corresponding to corner passages.
• For the horizontal positioning.
|
|
Product Description:
Easiest handling, most flexible, and strongest composite rope available on the market.
Features:
Polyolefin keeps line diameter up without adding weight.
Very little water absorption
Multiline II will not break down from UV exposure
Soft, spun polyester is added to the surface for better grip and chafe protection.
Medium Lay
|
|
Features:
Lightweight
Floats
Low cost
Applications:
Multi-purpose use for non-critical applications
Colors Available:
Yellow
Lengths Available:
1200'
600'
|
|
Our products have many uses in industrial contexts
Products available:
|
|
Product Description:
Endura 12 is manufactured from 100% HMPE fiber. The result is a rope that is extremely high strength, very lightweight, and very low stretch. The 12-strand single braid construction is supple, non-rotational, and easily spliced. Endura 12 is ideally suited for wire replacement and where weight is a primary design consideration.
Applications:
Replacement for steel cable
Winch lines
Helicopter lifting lines
Underground pulling lines
Slings
Tug boat tow lines
|
|
Product Description:
Made from Endura Braid, a double braid with a very high strength, extremely low stretch HMPE core with a durable polyester cover. Higher strength-to-diameter ratio enables smaller diameters to be put into service which can be advantageous when winch drum/take up length is a limiting factor. Eyes can be spliced on one or both ends and are available soft or with your choice of thimbles. We offer Galvanized, Heavy Duty Galvanized, Bronze, and Stainless Steel thimbles.
Features:
Factory spliced Eyes
Optional urethane coating can be applied to entire assembly or eyes only.
|
|
| ... products without technical information |
| |
One of the areas which makes Idem's Guardian Line Rope Switch Line new and innovative is in the area of rope connectivity. Traditional ‘turnbuckle’ style rope fasteners and adjusters are prone to rope slippage and require frequent re-tensioning leading to production loss caused by machine down time.Idem has overcome this common problem by providing a ‘no nuts or bolts’ rope connection system with a ‘Quick Link’ clasp at one end of the rope and a patented Tensioner /Gripper at the other.
The Tensioner / Gripper is located at the switch (rather than elsewhere along the rope length) so that the switch tension window can be viewed.
Final setting and locking can be achieved in a matter of seconds without any need for frequent re-tensioning.
|
|
Pizzato Elettrica has designed and patented new accessories to install the rope of safety switches faster and to obtain an aesthetically more pleasant system.
The new accessories, in comparison with the traditional fixing system through carpentry material, have the following advantages:
%u2022 The installation is faster because only one screw is used for the fastening of every rope extremity, and the parts are prepared to ease the installation. Some practical tests have pointed out that the installation time is halved, reason for which it is named FAST.
%u2022 The system is aesthetically pleasant, because thread parts (which sometimes tear operators%u2019 dresses) and the rope extremities, usually fixed by heat-shrinkable sheath or adhesive tape, have been hidden.
%u2022 The red plastic covers of the fixing parts have been developed also for the function of controlling the rope clamping. If the rope fastening screw is not fixed tightly enough, the cover cannot pass.
%u2022 The rope is fixed without folds, thus reducing the rope stabilisation time and the possible re-calibrations of the rope tightening.
Furthermore two sturdy pulleys has been introduced in applications where the rope is very long in order to support the rope length or to bend its route. They are designed to avoid any deformation and to allow the rope to remain in its seat also when it is energetically activated.
|
|
GLS Rope Switch
Idem Guardian Line Safety Rope Switches are designed to be mounted on machines and sections of conveyors which cannot be protected by guards. In contrast to traditional mushroom-head emergency stop buttons, Safety Rope Switches can initiate an emergency command from any point along the installed rope length and provide robust Emergency Stop Rope Pull protection for exposed conveyors or machines.
On pulling the rope, the safety contacts are positively opened and the auxiliary contact are closed. The switches are mechanically latched and can then only be returned to the operational condition by pressing the blue reset button (as required by EN418). A bi-colour LED indicator is available to enable switch status to be viewed from a distance.
Satisfies EN 418 and IEC 947-5-1 IEC 947-5-5
Guardian Line GLS features:
Die Cast Yellow Painted enclosure
IP 67 for hosedown.
Contact blocks (4 pole) 3NC + 1NO or 4NC or 2NC + 2NO.
3 conduit entries M20 or ½" NPT
Protect hazards up to 80 m. long.
Reset by push button.
Rope tension indicators.
Optional Signalling lamp available Green / Flashing Red 24V dc.
Rope pulled and breakage detection.
E-Stop Mushroom type button fitted.
Explosion-proof version available
|
|
GLM Rope Switch
Idem Guardian Line Safety Rope Switches are designed to be mounted on machines and sections of conveyors which cannot be protected by guards. In contrast to traditional mushroom-head emergency stop buttons, Safety Rope Switches can initiate an emergency command from any point along the installed rope length and provide robust Emergency Stop Rope Pull protection for exposed conveyors or machines.
On pulling the rope, the safety contacts are positively opened and the auxiliary contact are closed. The switches are mechanically latched and can then only be returned to the operational condition by pressing the blue reset button (as required by EN418). A bi-colour LED indicator is available to enable switch status to be viewed from a distance.
Satisfies EN 418 and IEC 947-5-1 IEC 947-5-5
Guardian Line GLM features:
Die Cast Yellow Painted enclosure
IP 67 for hosedown.
Contact blocks (4 pole) 3NC + 1NO or 4NC or 2NC + 2NO.
3 conduit entries M20 or ½" NPT
Protect hazards up to 50 m. long.
Reset by push button.
Rope tension indicators.
Optional Signalling lamp available Green / Flashing Red 24V dc.
Rope pulled and breakage detection.
E-Stop Mushroom type button fitted.
|
|
GLH Rope Switch
Idem Guardian Line Safety Rope Switches are designed to be mounted on machines and sections of conveyors which cannot be protected by guards. In contrast to traditional mushroom-head emergency stop buttons, Safety Rope Switches can initiate an emergency command from any point along the installed rope length and provide robust Emergency Stop Rope Pull protection for exposed conveyors or machines.
On pulling the rope, the safety contacts are positively opened and the auxiliary contact are closed. The switches are mechanically latched and can then only be returned to the operational condition by pressing the blue reset button (as required by EN418). A bi-colour LED indicator is available to enable switch status to be viewed from a distance.
Satisfies EN 418 and IEC 947-5-1 IEC 947-5-5
Guardian Line GLH features:
Die Cast Yellow Painted enclosure
IP 67 for hosedown.
Contact blocks (4 pole) 3NC + 1NO or 4NC or 2NC + 2NO.
3 conduit entries M20 or ½" NPT
Protect hazards up to 250 m. long.
Reset by push button.
Rope tension indicators.
Optional Signalling lamp available Green / Flashing Red 24V dc.
Rope pulled and breakage detection.
E-Stop Mushroom type button fitted.
Explosion-proof version available
|
|
Pull-wire emergency stop switches are mounted on machines and sections of plants which cannot be protected by guards. In contrast to mushroom head Emergency Stop push buttons, on pull-wire switches the Emergency Stop command can be initiated from any point on the wire.
In combination with one of the AES and AZR range safety monitoring modules, see chapter 10.3, ZS range pull-wire emergency stop switches can be used for Control Category 3 or 4 to EN 954-1.
Design and mode of operation:
All of the pull-wire emergency stop switches conform to European Standard EN 418. They have a positive linkage between the NC contacts and the wire rope. The pull-wire emergency stop switches are brought into the operational condition by pre-tensioning the wire, i.e. the NC contacts are then closed and the NO contacts open.
Schmersal make both standard and AS-i Safety at Work pull-wire emergency stop switches.
Click here to see the AS-i models
Or for the standard models click below
|
|
Stainless Steel Rope Switches
Idem Guardian Line Safety Rope Switches are designed to be mounted on machines and sections of conveyors which cannot be protected by guards. In contrast to traditional mushroom-head emergency stop buttons, Safety Rope Switches can initiate an emergency command from any point along the installed rope length and provide robust Emergency Stop Rope Pull protection for exposed conveyors or machines.
On pulling the rope, the safety contacts are positively opened and the auxiliary contact are closed. The switches are mechanically latched and can then only be returned to the operational condition by pressing the blue reset button (as required by EN418). A bi-colour LED indicator is available to enable switch status to be viewed from a distance.
Satisfies EN 418 and IEC 947-5-1 IEC 947-5-5
GLS-SS features:
Hygienic stainless steel 316 enclosure.
All screws and external/internal fittings stainless steel.
IP 67 - Ideal for food industry applications.
Contact blocks (4 pole) 3NC + 1NO or 4NC or 2NC + 2NO.
3 conduit entries M20 or ½" NPT
Protect hazards up to 100 m. long.
Reset by push button.
Rope tension indicators.
Optional Signalling lamp available Green / Flashing Red 24V dc.
Rope pulled and breakage detection.
Optional Extra E-Stop Mushroom type button available.
Explosion-proof version available
|
|
Emergency pull-wire switches
ZS 80
Metal enclosure
4 contacts
Position indicator and integrated emergency-stop push button
Wire length up to 75 m
Pretensioning force 100 N
Lever for release and position indication
Watertight collar
Wire pull and breakage function
Indicator lamp available
|
|
|
|
see the results for the following category
