|
|
|
Diamond circular saw blades are used to cut granite, marble and other natural stone, as well as brick and tile, and are available in sizes from 4 to 140 inches in diameter. In situations where noise-reduced suppression blades are required, Asahi Diamond's medium-diameter Prime Saw blades are ideal, featuring improved cutting finish and precision, as well as longer life, than conventional blades.
|
|
|
Cranden diamond products have 10 years experience designing and manufacturing diamond chamfer wheel, cut-off saws and grinding drums for all the major pipe manufacturers in the middle east and world-wide. Our special mixture of diamond grit sizes and types ensure that cranden diamond products last longer and grind faster than anybody elses. All products are made at our factory in england, guaranteeing the highest quality and speed of delivery anywhere in the world.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
|
|
VULCAN
The Vulcan 16mm diamond drilling bit is the new industry standard. Designed by Fordia for all types of ground, this exclusive and proprietary design is the first true 16mm bit and reduces the number of pull-outs by 33% in comparison to the 12mm bit.
T XTREME CORE BITS
Fordia's T Xtreme core bits series offer extreme structural enhancements and deliver more performance.
SHARK
The high quality diamond core bits in the SHARK series provide high performance in all types of formations.
The high performance SHARK series of impregnated diamond core bits are designed to meet today's challenging drilling conditions. SHARK’s quality impregnated matrices suit all possible formations, from soft to very hard, whether abrasive or silicified. Using the latest technology and equipment, we strive to give you core bits that penetrate faster and have a longer bit life.
DXP2
Tough 8
This matrix of medium hardness is ideal for drilling soft and hard rock. Durable with a low abrasion factor. Each segment of the bit is individually pressed at very high pressure to confer extra strength. A flexible tool well adapted to broken terrain.
P200
For more than 20 years, this bit has been the favorite choice of Australian drillers. Its soft and medium hardness matrix makes it ideal for most types of drilling. The P200 offers a great balance between efficient drilling and life span. This bit delivers better productivity and a greater rate of return from drill sites.
|
|
|
RHINO reaming shells sold at Fordia are manufactured with high-quality diamonds set into a high-strenght matrix, therby providing an excellent lifetime. The diamond-coated sections of the tool are cast directly onto the matrix and the reinforcement of the tool ensures maximum performance as the shell will maintain a full gauge hole in all types of ground.
|
|
|
Metal ores are mainly produced and exist in formation and fracture band of rocks, mostly hard, brittle and broken rocks which are very abrasive. With good diameter keeping ability and abrasion resistant bond, our diamond impregnated drill bits drill fast and last long. The newly developed wire line bits are excellent for drilling holes deeper than 800 metres. Most drill bits are produced with hot press sintering, the bond hardness is HRC26-45
|
|
Looking for a large selection of diamond bits with worldwide service and supply? Then look no further.
Atlas Copco sells Craelius and Hobic, two of the most famous bit names in the world. The two names - with different product profiles, specialties and features - cover all the diamond tools you need for whatever type of core drilling you're doing.
Atlas Copco has these two separate product lines, to respect customer requirements for different technical solutions and the specific traditions that the two names represent.
|
|
| ... products without technical information |
| |
DIAMOND AFFUTAGE
GLASS - TILING
5090V Intensive-use glass drill bit
5005V Multipurpose drill bit
|
|
Blind, stepped and through bore single pass diamond tools
Plateau superfinishing tools for bearing ratios exceeding 60%
Manually adjusted or auto – Compensation tools
Bore size from .080” to 8.00”
Single pass stock removals to .200”
Finishes as fine as .05” Micrometers (2 micro inch)
Size Control below 0.5 micron (20 millionths)
|
|
| ... products without technical information |
| |
|
MBG diamond grinding products offer the most tightly controlled properties and characteristics of any grinding diamond in today's market. From the most well-defined crystals to highly friable irregular shapes, the MBG product line offers tailor made diamonds for a wide range of grinding applications in non-ferrous materials.
|
|
All-Diamond Tipped Mills - DAD15, DPD15, EDPD15
High-speed and High-precision milling of aluminum alloys
All-PCBN Tipped Mills - QPP15
High-speed and High-precision finishing of gray cast irons
- Highly accurate machined surface
(aluminum alloys: Rz up to 2.0 µm; Rmax up to 3.0 µm with wiper insert)
(gray cast irons: Rz up to 3.0 µm; Rmax up to 6.0 µm)
- High speed milling
(aluminum alloys: up to 4000 m/min
cast irons: up to 2000 m/min)
|
|
DIA-Tools for the Highest Precision
By working requirements and construction possiblilities, DIA-tools are made in the bonded form (e.g. cutters, saw-blades, drill and surface cutters or with substitute cutting edges e.g. cutting heads or cutting tools).
Also all known tool forms can be produced with polycrystalline diamond cutters. The cutting geometry of the DIA-tools (e.g. hook, cutting angle and back angle) are specially made to suit the materials to be cut.
|
|
in ultra-hard materials
Face milling cutter PF 1000
Cermet and ceramic tools
PCD- and PCB-tipped tools
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
see the results for the following category : 
