Clevis pins

P. 18
install the governor weights 95k the hydrovoir governor sleeve 95m using governor weight clevis pins governor weight cotter pins 95j r the head the clevis pin must contact the tall ear the hydrovoir governor sleeve the two weights must be identical place the hydrovoir governor sleeve assembly

P. 20
b actuator b b 1 b b 95h b b as req d b b actuator spring b b ar b b ar b b 95j b b 2 b b governor weight clevis pin b b 2 b t b 95k b b 2 b b governor weight b b 2 b b 95m b b 1 b b hydrovoir governor sleeve b b 1 b b 95n b b 1 b b rear actuator gasket b b 1 b b 1 b b 1 b b 95p b b 1 b b spring

P. 7
when using depth micrometer refer to steps 16 17 18 19 shaft adjustment using the wilfley shaft adjustment gauge 12 remove the governor weight cotter pins 29a governor weight pins 29 governor weights 28 unbolt remove the governor springs 25 bolts nuts 25ab these will not be reused leave the governor sleeve

P. 9
b shaft adjustment using depth micrometer b b 16 remove the govemor weight cotter pins 29a goveraor weight pins 29 govemor weights 28 unbolt remove the govemor springs 25 bolts nuts 25a b leave the govemor sleeve 24 bolted to the shaft b b 17 install the spacers 98n between the thmst drive sleeve

P. 17
the spring guide springs top the gasket b front actuator gasket 95a b b inboaro lock rin6oring 95q b i 9632 m b gasket seal surface b b 9632 inboard lock ring c95e b check the gasket surfaces the actuator to be sure they are smooth free nicks be sure the antirotation pin is securely mounted the actuator

P. 2
Type Coupler Heights Minimum Maximum Jaw Coupler in (mm) 9.0 (228) 14.9 (380) Tow Eye in (mm) 9.3 (236) 15.3 (387) Pin & Clevis in (mm) 7.3 (186) 13.3 (337) Dimensions TGXseries Adjustable Coupler Plates Coupler plate allows each type of coupler to be adjustable in 1" increments Pin

P. 4
-function LCD display with: ? PIN access ? Selectable performance modes ? BDI and speedometer ? On-board diagnostics and troubleshooting 2. Fixed steer head 3. Twin picking steps 4. Towing eye, pin and clevis, and other coupler designs available 5. Magnetic mount convenience tray with stretch wrap

P. 3
. Battery roller design provides easier battery change out. Includes removable side gates. Optional multi-function LCD digital display includes PIN codes to restrict truck access, selectable performance modes, battery discharge indicator and speedometer. It also offers on-board diagnostics

P. 16
Clevis Pin 11 Cotter Pin 12 Pneumatic Cylinder Hardware 13 Grease Nipple 14 Flat Head Screw 15 Hex Hd Bolt w/ Lock Washer 16 Hex Hd Bolt w/ Lock Washer Options 17 Lower Stem Guard (Bellows) 18 Lower Stem Guard Clamp

P. 13
The sequence for disassembling the knife gate slurry valve is described below. Refer to the general assembly drawing for component location. 1. Actuate valve to the open position. 2. Remove valve from the pipeline. 3. Loosen the CLEVIS PIN from the GATE. 4. Remove the ACTUATOR ASSEMBLY from the YOKE. 5

P. 15
Isogate WS Series Knife Gate Valve IOM Manual 15 WS Series Knife Gate Valve Assembly Diagram Valve Sizes 2?-16? ? PNEUMATIC ACTUATOR Item Description Base Valve 1 Body 2 Sleeve 3 Load Distribution Ring 4 Upper Seal 5 Grease Nipple 6 Gate 7 Yoke 8 Clevis 9 Clevis Pin 10 Cotter Pin 11

P. 14
Isogate WS Series Knife Gate Valve IOM Manual 14 WS Series Knife Gate Valve Assembly Diagram Valve Sizes 2?-16? ? MANUAL ACTUATOR Item Description Base Valve 1 Body 2 Sleeve 3 Load Distribution Ring 4 Upper Seal 5 Grease Nipple 6 Gate 7 Yoke 8 Stem Assembly 9 Clevis Pin 10 Cotter Pin

P. 4
- Btm 25=Prox Switch SPDT - T&B 27=Prox Switch SPDT - Top 28=Prox Switch DPDT - Btm 29=Prox Switch DPDT - T&B 32=Prox Switch DPDT - Top 35=Wired Valve Location Tag 36=Pinned Valve Location Tag 37=Wired Cust. Nameplate 38=Pinned Cust. Nameplate 41=Hydraulic Coupler 99=Chain FT ___ Length

P. 3
trolley. Remove the cotter pin from the clevis pin on the trolley, slide the clevis pin out, lower the shackle and raise the cable so the shackle can catch the ring on the saddle sling. Move the shackle back up to the trolley, secure it by pushing the clevis pin through, and then secure the clevis pin

P. 15
5 release the pawl control lever to allow the pawl to engage the wrench head 6 position the wrench the first bolt to be loosened using the setup previously determined the wrench will hold itself as pressure is building up but it will loosen as pressure is released 7 engage the pin the front clevis

P. 7
b parts list series 1504 pawl carrier assembly b 9632 see figure 3 b item b b part b b description b b 6 b b b94067 b b 4 thinline pawl carrier b b 7 b b a94144 b b 4 thinline pawl b b 8 b b rp212 b b 1 8 x 3 4 roll pin b b 9 b b 13b020ge s b b pawl spring b b 10 b b a87059 b b clevis spring b b 11

P. 10
standard which matches your flange use that setup 4 insert the pin 7 through the back clevis 8 the hydraulic cylinder 2 the clevis ring 9 the reaction plate 3 refer to figure 6 5 measure the distance the wrench arm this distance is 4 series 1504 figure 7 10

P. 11
b figure 7 b 6 when the wrench reaction unit are properly placed the flange the distance l from the center the pin the back clevis the cylinder to the center the bolt being turned should always be 91 16 series 1504 7 place the wrench head 1 any bolt the flange 8 place the ring the reaction plate 3

P. 9
7 b 3 b b figure 6 b 4 refer to figure 6 during assembly 5 insert the bolt 5 through the hole the reaction leg 4 the corresponding hole the reaction plate 3 as shown the layout figure 4 is sample layout that flange tighten the nut 6 6 insert the pin 7 through the back clevis 8 the hydraulic