|
|
These high performance ovens offer industry leading production ratings and consistent high quality carbon fiber. Despatch Industries patented center to ends design yields tight temperature uniformity where you need it. Customized solutions optimize cost of ownership, power consumption and safety.
-Design forces air to move completely parallel to the flow of the fibers
-This design allows carbon fiber ovens to operate at consistently higher
temperatures without reaching uncontrolled exotherm
-The result of this technology is that manufacturers achieve 20% higher yields
with uniform density
|
|
|
Automated Fiber Placement (AFP) is traditionally used on very complex surfaces and smaller structures and utilizes single or multiple narrow, slit tapes or tows to make up a given total prepreg band width. This is typically the case within Automated Dynamics as well, but we have taken some liberties with the definition when it improves the Customer's automation solution. The Automated Fiber Placement Process is depicted to the left. In both thermoset and thermoplastic processing, incoming tape is electrically heated using nitrogen. Prepreg material application and consolidation or debulk is always achieved through a compaction roller medium that may be heated or cooled.
|
|
|
With the WOLFANGEL® Vario Cutter it is possible to cut the fibres with a speed up to 20 m/sec. The length of the fibres can be changed during the cutting process at full speed. With this cutter it is possible to produce fibres with a length between 3 up to 100 mm. The cutter can be driven by either a hydraulic or an electric motor. With the possibility of different combinations between knife and rubber role, it is possible to cut nearly all types of fibres.
|
|
|
For GFK-/CFK-materials, reinforced materials foam materials. Standard serrations type N, type WD, type GR
|
|
|
|
|
|
UltraMAX Chopper & Saturator
The MVP UltraMAX™ FIT® Chop system is THE ONE the other guys compare themselves to.
Rapid Access Design for easyacces
Low Pressure FIT® Technology
The MVP UltraMAX™ FIT® Chop system is THE ONE the other guys compare themselves to. The MVP UltraMAX™ FIT® Chop system delivers power, versatility and rugged construction for long lasting use. MVP's Rapid Access Design (RAD) serves you with easy maintenance, and reliable performance.
The MVP UltraMAX™ FIT® Chop system is the low pressure champion. If your goal is to make quality parts with minimal overspray and no wasted materials, then low pressure is the way to go. With the UltraMAX™ pumping system, the MVP FIT® Chop system utilizes the lowest pressure (15 - 30 psi) on the market.
The latest technology in emissions control is the patented FIT® (Fluid Impingement Technology). When you use FIT® technology, you can be assured you are armed with the latest state-of-the art weapon against harmful emissions. The MVP UltraMAX™ FIT® Chop system has the lowest emissions available.
Precision counts! The key to efficient FRP production is achieving a uniform laminate. With no splashing or bounceback and less air entrapment, the UltraMAX™ FIT® Chop system produces a stronger, more uniform laminate. Call today and let us create the solution for your FRP needs!
|
|
|
|
|
|
As all WOLFANGEL products, the fibre spraying plants distinguish themselves by their simple handling and high reliability. After the working process, the flushing of the plant is easily and unproblematically done by flushing valves. 3 rovings can be cut at the same time with the cutter. Resin and catalyst are delivered by means of piston pumps, which are connected to each other via a dosing lever so that the dosing of resin and catalyst is always exact, independent of the delivery speed of the pump. Without additional valves at the cutter, resin and glass can be directed at the outlet lever of the gun. The standard type plants are equipped with a solid cart with a 2-piece boom. The cart is big enough for a 200 ltr. barrel and a 30 ltr. resin can. As optional, this unit can be equipped with a resin control, a revisable catalyst intake system etc.
Due to our low pressure system, the quantity of resin and glass is continuously adjustable so that the production of big and small component parts is easily possible with the same machine and this without having to change the pump pressure or the spraying valve.
|
|
Simultaneous resin & fibreglass spray-up is nowadays employed in a great variety of applications.
Matrasur Composites proposes a series of spray-up machines which cover a wide flow rate range, from small complex parts to large parts.
These machines can be equipped with 6 different spray-up guns and 4 different fibre choppers.
Contact us in order to determine together the chopper unit that adapts the best to your application. Rollers and other accessories complement our chopper systems.
|
|
|
|
|
|
RimCraft set out in the mid 90's with the hope of improving technology in the processing of gypsum based products. Since then RimCraft has become the leader in providing tomorrow's gypsum processing technology TODAY!
RimCraft builds systems for spraying (GFRG) and dispensing catalyzed gypsum products. These products are used primarily for the Glass Fiber Reinforced Gypsum, GFRG, indoor architectural markets. Although we build standard systems, our ability to customize is where we really shine. The RimCraft Gypsum Spray Systems will also spray polymer modified gypsum (FMG), opening up the market for outdoor applications.
The RimCraft Gypsum Spray Systems were designed, engineered, and constructed to process gypsum materials in production environments, unlike competitor's systems on the market that were intended to process other materials such as cements. Take a closer look at the RimCraft Gypsum Spray Systems and you will easily notice why RimCraft has become the Leader in Gypsum Processing Technology.
|
|
| ... products without technical information |
| |
Data and energy
Unrivalled worldwide, eks Engel presents a new Hybrid Splice Box inside the FIMP product line that makes it possible to combine data and energy.
Furthermore, a new version with a SC-RJ coupling which allows combining multimode, singlemode and POF in one plug will be presented. The front panel of the Hybrid Splice Box can be outfitted with up to four RJ45 Click&Snap-, or alternatively with two Smart Hole-Modules.
|
|
Up to 24 channels (48 fibers).
For installation in 19" racks in distirbutors acc. to ISO /IEC 11801, ISO / IEC 24702 and EN 50173 family. Ready to accept all common types of factory or on-site assembled cables. Especially suited to accept our factory assembled OSI PreCONNECT® cabling system.
Two types are available:
fixed installation
telescopic complete-pullout
|
|
Mit der Serie FIMP stellt eks Engel eine industrielle Kompakt-Spleissbox für bis zu 12 Lichtwellenleiterfasern vor. Die Box ist spleißfertig bestückt und integriert Spleisskamm, Spleissablage, Kupplungen, Pigtails sowie die Kabelverschraubung. Als Kupplungsvarianten stehen SMA, ST, SC, LC, FC-PC und E-2000 zur Verfügung. Alternativ ist die Spleissbox auch variabel bestückbar.
Durch seine gleichermaßen kompakte wie robuste Bauform und dem Gehäuse in Edelstahl ist die Spleissbox für den Einsatz im rauen industriellen Umfeld prädestiniert. Zur schnellen und problemlosen Montage wird die Spleissbox per Clip auf eine 35 mm-Hutschiene befestigt. Zudem ist ein Kit für die Wandmontage erhältlich.
|
|
The inner values of the FIMPXL are really convincing and the installation is quite simple and done very fast.
FIMPXL is ready for splicing and it already contains splice tray, couplings, pigtails and cable gland. Regarding different couplings, you can choose from SMA, ST, SC, LC, FC-PC and E-2000. The front panel and the splice cassette can be removed for splicing and since the cassette is magnetic, it can easily be fixed onto a splice unit. The cassette has got a hole for splice units with a bolt.
The powder coated stainless steel housing is also magnetic so that the splice box can easily be affixed to another housing or to a switch cabinet in case of no different tray. Furthermore, FIMPXL has got a clip for DIN rail mounting (35mm) and a kit for wall fastening. Thus, there are space-saving and flexible solutions for mounting our FIMP.
|
|
|
The OP104 is a modular approach to passive components. By packaging couplers, splitters, WDM, isolators and polarizers into a rugged module test setups can be better organized with less 'floating' fiber and coiled up patch cords.
|
|
|
|
|
|
Universal mechanical tension meters for versatile applications in textile, fibre and wire industry.
- The analog display shows changing and fluctuating tensions fast and enables an optimal process adjustment
- The built-in material thickness compensator compensates different material diameters for a particular range
- Filament guide and roller shifting mechanism ensure easy acquisition of the running material
- Hand-held unit with built-in mounting holes permit fixed installation for continuous tension measurement
- Special finger support located on the rear side reduces the effort to move the outer roller assembly
- Custom-built configurations and special calibration are available
- Everything in operator’s view:
· the guide rollers
· the measured material
· the readings
- Ball-bearing mounted, V-grooved guide rollers
- Each instrument is individually calibrated for highest accuracy 41 mm Ø scale
- Tension meter with rugged aluminium housing
- Certificate of Compliance with the order 2.1 according EN 10204 is included
- Optionally available: Inspection Certificate 3.1 according EN 10204 with calibration report
|
|
|
|
|
|
Electronic tension meter for applications in textile and wire industry.
Special convenient for users aquiring additional process data to save them for example for a QM-system ISO9000ff
Model DTMX offers additional features to model DTMB:
- data memory
- statistical analysis
- interface for data printer and PC connection
Applications in textile industry: e. g. 50 up to max. 50000 tex
Applications in wire industry: e. g. 0.08 up to 2.2 Ø mm copper wire
9 Tension ranges from 0.1 - 200 cN to 5 - 50 daN
- Microprocessor controlled tension meter for highest accuracy
- Measuring principle: double beam in bending with strain gauge
- Selectable update rates (0.5, 1, 2, or 4 seconds) to provide steady readings
when tensions fluctuate (electronic damping)
- Measuring frequency: 62 measurements/second
- Built-in mounting holes permit fixed installation for online use
- The display shows averaged values calculated during the
update interval t1 e. g. every second 1 x
- Saving MIN, MAX and PEAK values during a user-selected period. These values can be recalled at the display.
- Zero adjustment feature permits use of the tension meter in various measuring positions, maintaining highest accuracy
- Calibration to customer supplied material is available (up to two different material calibrations)
- Tension meter with built-in material thickness compensator improves accuracy for changing diameters (from tension range - 500 cN)
- Hand-held unit with built-in mounting holes permit fixed installation for online use
|
|
Stationary electronic tension sensor for measuring materials with differentdiameters.
Online Sensor for wire and textile industry.
Measuring range up to 50 daN.
- Easy installation
- Tension sensor with integrated measuring amplifier
- Various output signals
· analog
· digital (optional)
· current (optional)
- Many configurations are possible
- Easy calibration to customized material by operator
- Tension sensor with mechanical overload protection
- Wide variety of roller types can be specified
- Different guide rollers, ball-baering mounted
- Tension sensor with rugged aluminium housing
- Certificate of Compliance with the order 2.1 according EN 10204 is included
- Optionally available: Inspection Certificate 3.1 according EN 10204 with calibration report
|
|
These high performance ovens offer industry leading production ratings and consistent high quality carbon fiber. Despatch Industries patented center to ends design yields tight temperature uniformity where you need it. Customized solutions optimize cost of ownership, power consumption and safety.
-Design forces air to move completely parallel to the flow of the fibers
-This design allows carbon fiber ovens to operate at consistently higher
temperatures without reaching uncontrolled exotherm
-The result of this technology is that manufacturers achieve 20% higher yields
with uniform density
|
|
... see all the products in the category
Ovens
|
|
|
see the results for the following category : 
