|
|
| ... products without technical information |
| |
Install these compact sensors anywhere for accurate point sensing and fast response. All Thermal-Tab modules use a thin-film RTD element. All Thermal-Ribbon models conform to EN60751 Class B tolerance when ordered with a PD platinum element.
- Fast response surface sensing in aerospace, medical and industrial devices
- Rugged lamination construction
- Polyimide, silicone rubber or Mylar™ insulation |
|
| The Ni1000SOT is a nickel thin film resistance temperature detector (RTD) that is suitble for use in contact temperature sensing. The characteristics of the temperature sensor comply with DIN 43760. The Ni1000SOT is manufactured by PVD-depositon on a silicon substrate. The thin film structure is covered by a passivation layer for environmental protection and enhanced stability. The nickel elements are mounted on lead frames and encapsulated in SOT23 packages. This technology allows the production of miniature, low cost, high precision temperature sensors. The Ni1000SOT sensor is qualified for the most demanding automotive applications (including exposure to hot oil) and is suitable for many more applications in harsh environments. |
|
Measurement Specialties offers high end temperature sensors through its recent acquisitions of BetaTHERM and YSI Temperature. Both companies specialize in negative temperature co-efficient (NTC) thermistors for precision temperature measurement in environments where there is a high cost of failure.
Thermistor-based temperature sensors exhibit a change in their electrical resistance in response to a change in ambient temperature conditions. They are highly-sensitive and have very reproducible resistance-versus-temperature properties. Thermistors can be further classified as either “Positive Temperature Co-efficient” (PTC thermistors) or “Negative Temperature Co-efficient” (NTC thermistors). Both PTC and NTC thermistors have distinct features and advantages that make them ideal for different end-use sensor applications. Whereas PTC thermistors demonstrate an increase in resistance when subjected to an increase in temperature, NTC thermistors demonstrate a decrease and are commonly used for more accurate temperature sensing. This accuracy makes them unique in their functionality in many applications compared to other temperature sensors/switches such as thermocouples or electromechanical thermostats, which they are steadily replacing.
NTC thermistors are available in a wide variety of configurations and protective coatings to suit almost any application. The particular features and advantages of NTC thermistors compared to other sensor types include:
Large temperature sensitivity and broad range of function
Available in many physical forms and not constrained by material types
Interchangeable devices eliminate need for individual sensor calibrations
Good electrical noise immunity
Easy to interface to electronic instrumentation
Can be customized to optimize thermal response requirements
NTC thermistors are the most versatile and cost-effective temperature sensors in terms of satisfying typical selection criteria and in their inherent advantages over other sensor types.
|
|
The L Series offers a choice of precision thermistors that are designed for close tolerance resistance temperature curve tracking over standard temperature ranges. They can be used for any general temperature measurement, control or compensation application where interchangeability and low cost are major considerations. The L Series is available in two types A & B. The A type can be used in standard probe assemblies. The B Type is specifically designed for PCB assembly.The stop tabs allow the component to be located in the same position on the PCB.
Features
• Uniform construction for automated assembly
• Low cost
• Operating temperature range from -40°C to +125°C
• Available in tolerances of +/-1%, +/-3% & +/-5%
• Beta Value tolerance on all products is +/-1%
• RoHS Compliant
Applications
• Disposable medical products
• Automotive applications
• Home appliances
• Air conditioning systems
• Refrigeration control
• Temperature sensing, control and compensation |
|
| The BetaTHERM Glass Series NTC Thermistors are the perfect choice for applications that require high stability and performance in harsh environmental conditions. The Glass A Series uses a hermetic glass encapsulation to allow improved resistance to humid environments. With an operating temperature range of -55°C to +250°C, these NTC Glass Sensors are suitable for elevated temperatures or applications where rapid thermal cycling are present. With resistance tolerances of +/-1%, +/-2%, +/-3% or +/-5%, these NTC glass thermistors are suitable for the most demanding requirements. |
|
NTC Thermistor soldered to 30 Tinned Copper wire with Teflon Insulation. The unit is positioned in the PVC Medical (HY-VIN VH787) tubing using UV curing agent. The PVC tubing compiles with the requirements of BS2463.
Features
• The sensor is available with highly flexible cable wires designed for Medical use.
• PVC Tube is hermetically sealed to provide a high level of protection to the thermistor.
• Available with cables and connectors or other requirments per customer specification.
• PVC tube complies with BS2463.
• Tight tolerance available - +/- 0.05oC from 32oC to 44oC. |
|
The rugged construction of the DO-35 package is ideally suited for applications which cover the temperature range from -40°C to +250°C with leads that are suitable for welding or soldering. The glass package hermetically seals to the metal leads which protects the thermistor element from extreme environmental conditions. The axial leads make this device a perfect choice for PC board mounting and the leads are plated giving a temperature rating to +250°C. The standard devices are specified as +/-1%, +/-3% and +/-5% at 25°C.
Features
• PC board mounting
• Hermetically sealed element. Glass metal package.
• Axial leads
• High temperature devices for applications to +250°C
• Time constant - 8 seconds in air
• Dissipation constant - 2.5mW/°C in air at 25°C
• RoHS Compliant
Applications
• Low cost probe assemblies
• High temperature printer ink sensors
• Consumer Electronics
• High temperature high-speed manufacturing
• Printed circuit board temperature sensing
• Air Conditioning |
|
| ... products without technical information |
| |
Hydrosteel 6000 is the ultimate portable monitoring tool for sour, HF and high temperature corrosion and diffusible hydrogen damage in steel.
The intrinsically safe instrument is totally non-intrusive and with minimal test surface preparation, and no consumables such as grease required, reliable measurements can be made within a minute.
Measurements can be taken from small pipes and large vessels, at any orientation and at any temperature up to 500 °C (932 °F), with a single probe. |
|
The MICRO III, with its small dimensions of only 4,7 x 8,8 x 2,5 cm, is the ideal gas detector for personal protection. The single gas detector with ATEX certification weighs only 75 g. It detects reliably oxygen, hydrogen or many toxic gases like hydrogen sulphide, ammonia, ozone, carbon monoxide, etc. The current gas concentration is shown on a large display. With a loud alarm of 95 dB and a changing frequency the small single gas detector is audible even in noisy environments. Simultaneously, two bright and alternately flashing LEDs indicate a gas alarm. Three alarm levels and the battery alarm provide comprehensive protection.
With a permanent operation of 24 hours a day a single AA battery powers this instrument for up to 9 months. The long-life smart sensors allow the change to other gases without any problems, since the detector recognizes the new sensor type. A high-performance pump (as per ATEX) for gas sampling can be easily attached, ensuring to detect gas hazards in confined areas.
Gases to be detected: O2, H2S, CO, NO, NH3, HCN, HCl, SO2, H2, C2H4O, SiH4, PH3, COCl2, NO2, Cl2, O3, ClO2.
|
|
| SIKO electronic displays are freely prgrammable via robust, front-sided membrane keyboard ensuring an easy and flexible adaptation for displaying different measured values. Depending on application, compact, simple units or multi-functional displays with RS485 interface are available. |
|
The Remote Display Unit (RDU 40) is a robust display unit for outdoor use in hazardous areas. If the number of temperature elements per tank is 6 or less, the RDU 40 is the most cost effective solution for field display. In this case the temperature elements can be connected directly to the TankRadar Gauge (RTG) without using a Data Acquisition Unit (DAU).
The display functions are software controlled by the connected gauge. It is easy to work with via the 4-key display keyboard. Each screen view can display 7 text lines with 16 characters per line.
It displays calculated data such as level, average temperature, volume, signal strength etc. Data can be displayed in lists or as single values, with a choice for the operator to have a user defined view. |
|
Display with 5 digits of 60mm height to be mounted on the crane.
The location on the beam of the crane or on wall makes the weight easily readable from the position of the operator.
Comptaible with our weighing systems via cable or radio.
Technical charactersitics
· 5 LED digits of 60 mm of height
· APower supply trough crane, 48, 110 or 220V
· Infrared remote control with fucntion Tare
· Connected via cable or radio |
|
| ... products without technical information |
| |
- Low cost and high flexibility
- Reverse or Forward Power
- Covers 63 to 690 VAC
- Available for 5A CT
- Programmable scales
- Programmable relay functions (NE/ND)
- Microprocessor based
- Optional Configuration by PC
The SELCO G-Line relays are mainly intended for use in land-based applications. The SELCO G-Line relays provides an efficient solution for applications where flexibility and cost of purchase are the main issues. Despite a low purchase price, SELCO G-Line relays provide high quality, proper measuring techniques and a vast number of programmable options. |
|
- Low cost and high flexibility
- Over and Under Frequency
- Covers 63 to 690 VAC
- Programmable scales
- Programmable relay functions (NE/ND)
- Microprocessor based
- Optional Configuration by PC
The SELCO G-Line relays are mainly intended for use in land-based applications. The SELCO G-Line relays provides an efficient solution for applications where flexibility and cost of purchase are the main issues. Despite a low purchase price, SELCO G-Line relays provide high quality, proper measuring techniques and a vast number of programmable options. |
|
Relays of the SUA200 series are designed to monitor the voltage in single-phase AC or DC systems. The devices are suitable for undervoltage and overvoltage monitoring (window discriminator function). External supply voltage is not required. The response values for undervoltage and overvoltage are individually adjustable.
|
|
- Low cost and high flexibility
- Three phase Over or Under Voltage
- Monitors phase failure & symmetry
- Covers 63 to 690 VAC
- Programmable scales
- Programmable relay functions (NE/ND)
- Microprocessor based
- Optional Configuration by PC
The SELCO G-Line relays are mainly intended for use in land-based applications. The SELCO G-Line relays provide an efficient solution for applications where flexibility and cost of purchase are the main issues. Despite a low purchase price, SELCO G-Line relays provide high quality, proper measuring techniques and a vast number of programmable options. |
|
| Many measurement tasks in the field of industrial test benches and automatic production/assembly processes can be solved very simply and reliably with HBM industrial measurement amplifiers. Force, pressure, displacement and torque transducers based on different technologies can be connected to these analog and digital amplifiers. |
|
interface technology
The TURCK interface product portfolio comprises a large variety of devices for isolation, conversion, processing and conditioning of analogue signals.
The housing designs comply with industrial standards:
series interface module (IM) in modular housings
series multimodul (MK) in modular housings
series multisafe® (MS) in modular housings
series multicart® (MC) on 19’’ card
Interfacemodule Cartridge (IMC) series for the IP67 area
|
|
| SIM-Small Instrumentation Modules-is a compact test and measurement platform for a wide range of applications. Unlike other modular systems, SIM offers complete front-panel as well as remote operation, allowing you to choose between manual and computer control. Up to eight instruments share the same mainframe which provides power, clock synchronization, communications, and module status. For additional versatility, you can cascade mainframes or other RS-232 instruments, and even operate modules outside the mainframe. |
|
| The measuring amplifier with comparator outputs works as a DC amplifier for DMS measuring bridges. Three downstream comparators having one adjusting potentiometer each allow for the setting of three different switching thresholds that correspond to a certain load of connected DMS force transducer. Each comparator output controls one relay and one indicator LED. |
|
Entis XS combines a broad range of inventory management functionalities with advanced automation and control of tank instrumentation. The Entis XS menu driven structure stands out by its user friendliness. This enables operators to navigate simply to the easily configurable Entis XS screens.
Entis XS offers unmatched engineering potential and flexibility for all tank utility applications. In this, the system anticipates future developments capable of further optimizing your business.
Entis XS is an open system with diverse interfaces to the field and to control, MIS and ERP systems. Depending on your requirements, virtually any server-client architecture can be implemented with Entis XS.
Entis XS: the only real integrated concept for advanced and total tank farm automation. |
|
| ... products without technical information |
| |
|
|
see the results for the following category