- Detection - Measurement >
- Force Measurements >
- Compression load cell
Compression load cells
Hydraulic pressure cells were developed to measure the total load in embankments and foundations and are mainly used in dams, tunnels, bridges. They may be embedded in concrete or cemented in fissures ...
... is selected from the best load cells and has very low non-linearity, hysteresis, eccentric load sensitivity, and temperature sensitivity. If you need to measure up to 50K pounds of force, ...
Interface, Inc.
... sliding weigh module or load point/weigh module system (load cell plus assembly) is designed for use on medium to high capacity vessels. Each weigh module consists of ...
Overload stopper included on low capacity side Tension - compression Not sensitive to side forces Precision class < 0.1% / capacity Similar in design to the F612TC and F501TC, these sensors allow for very ...
TME
Compression from 500 daN to 10,000 daN Miniature Precision class <1% / capacity F402C load cells series are designed minimal space use. They measure static and dynamic loads ...
TME
Tension - compression from ± 25 to ± 200 daN Compression from 25 to 200 daN The F480 TC series force sensor are all stainless steel and have a range up to 200 daN
TME
Rated force: 500 N - 50,000 N
type: load cell; accuracy class: 0.5 %; dimensions: Ø 40mm x 25mm; force transmission: load button R50, Ø 11 mm; connection: 3 m Unitronic FD CP Plus / 4x0,14; material: stainless ...
Rated force: 5 kN - 200 kN
... sheet 5 measurement points; 3 test series with 3 mounting positions; accessories: 2x washers for load distribution, diameter 12 mm x 3 mm; This force sensor is designed for fastener ...
Rated force: 1, 5, 10 kN
type: force sensor; accuracy class: 0,1 %; dimensions: 115mm x 60mm x 50mm; force transmission: 4x female thread M6 x 1; through bore: 1xfeedthrough 28 x 28mm; connection: integrated round plug connector M12, 4-pole, male; incl. ...
Rated force: 20 kN - 50 kN
... especially designed for applications in smallest room (diameter and height) where relatively large forces must be measured reliably.The compression force load cell ofthe ...
Rated load: 2.5, 5, 10, 20, 30 t
Weighing of hoppers, tanks and small and medium capacity silos, for non-trade use only. The TSL-INT load cell consists of a stainless steel body (according to IP 68). It is available in 5 capacities:2,5, ...
Rated force: 3,500, 3,400, 7,500, 1,200 N
Economical alternative for closing force calibration. Force indicated by a pointer on a scale. Ensures uniform and reproducible process quality. Three models available to suit closing force range. Developed for ear clamp installation ...
Rated load: 30,000, 40,000, 50,000 kg
• Steel, stainless • Hermetically sealed, Protection Class IP68 • Cable length 15 m • OIML test certificate • For more details, see data sheet 470.520.094
Rated force: 100, 200, 500, 1,000, 2,000 N
The S200 Load Cell is single point and low profile for accurate measurements of force up to 1000 N. The thin-film metal strain gauge circuit enables long-term stability of better than 0.1% per year. A ...
Strain Measurement Devices
Rated load: 100 kg - 1,000 kg
... IP65 protection grade. Model LAN-X2 load cells are designed to this “torque/multidirection force”type and manufactured from high quality aluminum alloy of aviation standard. LAN-X1 oad cells ...
Xiamen Loadcell Technology Co.,Ltd.
Rated force: 22 N - 2,200,000 N
Rated load: 5 lb - 500,000 lb
A load cell or force sensor is a device which converts load or force into an electrical signal. A load cell should ...
Rated load: 0.1 t - 30 t
This column load cell is with compression load structure. It is made of alloy steel or stainless steel. This column load cell can be ...
Aerospace Southocean(Zhejiang)Science And Technolo
Minebea manufactures load cells that use strain gauges to convert weight into electrical out put. These products are used to display, record and control weight and other factors, for digital weight scales ...
Rated load: 5 t - 50 t
The compression load cell 220 has been designed to operate in difficult and dangerous environments and it is suitable for weighing hoppers, tanks, silos and trucks. The load ...
Pavone sistemi
Rated load: 750 kg - 50,000 kg
The compression load cells BP are specially designed to work with compression with element detecting a shear or double shear. Airpes’ Compression ...
Airpes
Rated load: 5,500 kg - 23,000 kg
... UL series load cells are completely nitrided to make them highly corrosion resistant. They are available in two variants, namely, UL with solid rod and ULF with hollow rod. The former is fitted with a ...
Rated force: 0 kN - 100 kN
Rated load: 10 lb - 2,000 lb
Miniature Load Cells are designed for applications with minimum space and high capacity loads. The high performance strain gauges assure superior linearity and stability. ...
Rated force: 10 kN - 10,000 kN
... long term for BROSA compression load cells due to proven strain gauge technology and sophisticated amplifiers with reliable and accurate measuring results. There is a wide ...
BROSA AG
Rated force: 10,000 kgf - 20,000 kgf
Rated load: 10,000 kg - 20,000 kg
Height: 146 mm - 146 mm
... ST-2W type load cells are made of special alloy steel material that isolates it from corrosion and industrial environmental conditions. Operating with shear beam principle and having electrostatically ...
Puls Electronic
Rated load: 0.5, 1, 1.5, 2, 2.5 t
BR215 weighing platform scale foot load cell This weighing load cell could replace the weighing scales beam load cells feet. It means ...
Hefei Brans Measuring And Controlling Technology Co., Ltd.
Rated load: 10 t - 50 t
BR 016 Analog Load Cell BR016 is a high performance fully welded compression type load cell. It perfect fits for use in high capacity ...
ANADOLU BASKÜL ELEKTRONİK TARTIM SİSTEMLERİ LTD. ŞTİ.
Rated force: 4,448 N
The MCL6 is designed to measure cutting tool forces during turning operations, such as in a lathe, and features a tool holder mounting fixture. The instrument has a top mounting surface (6.5 inches square) equipped with mounting holes ...
Rated load: 20, 30, 40, 10 t
Height: 188, 214 mm
Column load cell is a sensor used for engineering force detection, overload safety detection and impact force measurement and control. It is suitable for sealed treatment and harsh environment. Suitable ...
Guangdong South China Sea Electronic Measuring Tec
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining