|
|
Sauer Industrial compressors UK offers 2-stage, 3-stage and 4-stage air cooled compressors covers from 40 bar up to 420 bar.
With the WP 4325 and WP 3215 compressor types, the existing Sauer line of air-cooled high-pressure compressors has been enlarged.
The Tornado series consists of the three-stage WP3215 and the four-stage WP 4325. Each of these is available in the "Basic-Version" - a compressor with motor and an optional separate control unit - and in the "Comsilent-Version" - a complete, ready-to-operate system with soundproof canopy.
The "Comsilent-Version" of a modern compressor center. Fully automatic electronic control, noise insulation down to 72dB (A) at a distance of has everything presently required 1m, integrated professional filter, demistor and condensate collector professional tank. The width of less than 800mm width allows it to be conveniently brought through any professional door, the maintenance points are easily accessible through a side maintenance hatch or a front side designed as a door.
Compressors of the Tornado series can naturally also be supplied fitted out for special applications, for example as a gas-tight version for compressing industrial helium, or for use in explosion-protected zones in compliance with ATEX regulations.
|
|
To be able to meet customer's demands for particularly low-maintenance compressors manufacturers, Sauer, in conjunction with well-known partners successfully developed a series of 3-stage air-cooled compressors at the beginning of the 1970s.
Through the division of compression into three stages, these designs demonstrate exceptional endurance even under very difficult operating conditions. We have delivered over 4,000 of these compressors to our customers all over the world for a wide range of applications - you too can benefit from our experience.
The performance of our machines 3-stage air-cooled compressors is matched only by our customer support: outstanding service you can rely upon at any time. Our business traditions are based on straight dealing, where honesty is always welcome and a handshake still counts.
Our full range stocks mean we can deliver spare parts required immediately - even for earliest generation compressor parts. |
|
The Hyper compressor is a high-pressure reciprocating compressor for low density polyethylene plants, with discharge pressure up to 3500 bar (50,000 psi). Burckhardt Compression has an outstanding experience of over 55 years in manufacturing Hyper compression trains. It excels with long lifetime and high safety requirements thanks to its unique design features and Burckhardt Compression's worldwide one-stop service.
The world's most powerful compressor, driven by a 27'500 kW (36,900 HP) electronic motor and compressing 160 tons of ethylene per hour to a discharge pressure up to 3100 bar (45,000 psi), was built by Burckhardt Compression in 2007.
|
|
oil-free
up to 150 bar
absolutely gas-tight
compressed air and gas
ATEX-conformity
air- or water-cooled |
|
HAUG PISTON COMPRESSORS FOR OIL-FREE PNEUMATICS
HAUG guarantees technically and economically optimal solutions for compressed air supply, with the security of a constant oil-free quality of the compressed air.
Universal ways of operation
Due to the dry-running technology the HAUG piston compressors can be out of operation, without causing any problem compared to lubricated-compressors and screw compressors manufacturers. Operation in idle run mode is not required.
Universal application for:
Continuous operation
Intermittent operation
Emergency or reserve operation
|
|
ENVIRONMENTALLY FRIENDLY COMPRESSION OF GASES A HAUG SPECIALITY
HAUG gas compressors run absolutely oil-less with dry lubrication. The oil-less compression avoids any contamination of the process gas and the process machinery.
To obtain an absolutely hermetically gas-tight unit, HAUG gas compressors supplier are equipped with a magnetic coupler. For this construction the permanent total gas leakage is less than 0.001 mbar l/s during operation as well as at standstill. In the case of helium at 3 bar pressure the gas loss is merely 5 grams per year! Contamination of the ambient environment through gas leakage with these compressors is practically impossible.
|
|
MEDO Air Blowers
applications:
- aeration of sewage treatment plants
- biogas plants
- aquatic
- medical
& more |
|
OIL-FREE COMPRESSORS MANUFACTURERS SERIES TF
The TF series of HAUG compressors is running completely dry, i.e., without professional cylinder lubrication and with no oil bath in the crankcase. Contamination of the pneumatics product with lubricating professional oils is thus excluded. Only an oil-free compressor system is capable of generating oil-free compressed
air on a continuous basis, ensuring that neither oil aerosols nor oil
vapours can enter the process.
Oil-free TF compressors are suitable for universal use. They are suitable for continuous operation, intermittent operation and for standby emergency operation with long periods of shutdown. These dry compressors are extremely reliable and permit highly economical operation with no idling costs. |
|
| Quality, reliability and cost effectiveness distinguish this series. These characteristics are proven daily by many customers world-wide under hardest conditions. |
|
OIL-LESS AND DRY COMPRESSION
A HAUG SPECIALITY
HAUG is the inventor of oil-less and dry-running piston industrial compressors. For decades HAUG compressors have proved themselves in difficult operational conditions and climatic environments. HAUG dry-running compressors are ideal for continuous operations, intermittent operations, and emergency operations with practically no running in time.
|
|
Air and gas compressors
GRASYS is the official and exclusive supplier to the Russian and CIS market of industrial compressors manufacturer, making of the German company Bauer Kompressoren. Bauer Kompressoren is one of the world leading manufacturers of medium and high pressure compressors (pressure range of 30500 bar) used for compression of air, hydrogen, methane, inert gases, such as nitrogen, industrial helium, and other gas mixtures.
Almost any Customer project may be matched with Bauer Kompressoren compressor equipment best professional fitting for each specific task:
Supplier of air compressors
G Series 2535 bar;
GB Series 3063 bar;
G Series 6490 bar;
GI Series 90500 bar.
Noble gas compressors (argon, helium, neon, etc.)
GG Series 90350 bar.
Nitrogen compressors
GGI Series 90500 bar.
Methane, associated and natural gases compressors
GC Series 90350 bar.
Compressors are produced in two configurations: vertical and horizontal.
Vertical configuration featuring the compressor-over-engine design is used in compressors with the capacity ranging between 100 and 600 nl/min
Horizontal configuration is used for compressors with the capacity ranging between 600 and 3500 nl/min.
All compressors are balanced and installed on elastic-damper supports eliminating the need for special fixation on foundation. It is sufficient that compressors are placed on an even surface, energized and connected to consumers.
Bauer Kompressoren is the only manufacturer providing industrial compressors with working cylinders surface nitrogenized with the use of gas or plasma coating technique. This helps to avoid replacement of working cylinders over the entire compressors operating life. Reduced wear of compressors final stages is achieved through the use of floating pistons (while piston rod is linked with guide piston, compressive piston moves freely with the elimination of normally present distorting loads). Manufacturers of roller bearings of crankshaft and piston rods are designed so as to provide for a considerable safety factor and over 30000 running time.
These measures along with the careful selection of lubricating oils contribute to the compressors high reliability by continuous service with long interval between scheduled maintenance. The design of compressors industrial cooling systems allow to provide the optimum cylinders thermal conditions and efficient gas cooling in inter-stage heat exchanges. |
|
| International shipping with its most stringent requirements for quality and reliability is Sauer's traditional field of activities. Our starting-air and working-air compressors suppliers have proven to be reliable in this demanding market. They count among the most modern and most economic compressors available today. In particular the 3-stage air-cooled starting-air compressors - in comparison to the traditionally used 2-stage water-cooled compressors - contribute significantly to modern ship operation concepts. With these products Sauer became one of the leading manufacturers of compressors for shipping and off-shore technology world-wide. |
|
The Laby compressor manufacturer represents unbeatable reliability and availability, thanks to its unique labyrinth sealing system on piston and piston rod gland that allows oil free and contact-free compression. The result is an extended meantime between overhaul, that has a positive impact on reliability and operating cost.
Neither contamination of the gas by abraded material from piston rings nor hot spots from friction occur. The Laby is designed to compress bone-dry, dirty, abrasive and other gases. The gastight casing reduces gas emission and losses to the environment to zero. The Laby compressor easily manages the compression of LNG boil-off gas at suction temperatures down to minus 160C (minus 250 F).
|
|
Sauer Manufacturers of compressors UK offers a wide family of gas compressors:
'H' series compressors are used for Air or Nitrogen compression. Each compressor is an air-cooled, single acting, three or four stage-reciprocating piston compressor with the combination of oil pressure fed crankshaft suppliers of bearings, and professional cylinder oil splash with regulated injection for the final high-pressure piston plunger design.
Performance with inert gases, such as Nitrogen, ranges from 10 to 150 Nm^3/h within a final pressure range of 100 to 350 bar including the Sauer unique NitroFlex integrated 'all-in-one' - Compressor, professional generator and gas industrial booster.
'W' series compressors are oil-lubricated, single acting water-cooled piston compressors for air or inert gas compression in two or three stages from 10 to 100 bar with gas flow-rates from 65 to 400 Nm^3/h.
'LB' series inert gas boosters are dedicated nitrogen gas boosters that can accept suction pressures from 4 to 14 bar to deliver gas to a maximum of 40 bar. This single stage gas booster range is the result of years of trouble-free experience with the 'L' range.
'L' series compressor/boosters offer a wide range of gas flow-rates from 10 to 400 m^3/h at pressures to 40 bar in two or three stages based upon the established marine diesel air-start Sauer range of two and three stage oil-lubricated, piston compressors. Even as professional air compressors they can be safely adapted for use in Ex-atmospheres to ATEX regulations
|
|
JAB Kompressors are own developments with the knowledge we gained during the construction of our compressors with a performance up to 350 Bar.
The main characteristics of these machines are oil pressure lubrication, oil pressure control, oil pressure monitoring, shut down in case of lack of oil, oil and water separation with automatic discharge and condensate separation as well as very low noise emitting values.
|
|
Advantages of JAB Compressors manufacturer For Gas Compression
Compressor 4 stages, air cooled
Compression proofed crankcase
Gas proofed shaft packings through axial face professional seals
Oil pressure lubrication for crank drive and piston of the 3rd and 4th stage
External lubricating industrial oil filter
High efficient cooling system
Maintenance-free oil and water separator
Micro professional filter at the high pressure gas outlet
Efficient, economic, easy maintenance
|
|
The process gas compressor represents high availability and a long meantime between overhaul thanks to an optimized selection of high quality components and cocks that result in low operating and maintenance cost. Burckhardt Compression has over 160 years of experience in manufacturing piston compressors and offers a worldwide one-stop service.
The company provides a robust and reliable process gas manufacturers of compressor of Swiss design and manufacture. It is designed according to individual application requirements within the API 618 specifications. It is available oil-free or lubricated, horizontal or vertical. It handles easily hydrogen, hydrocarbons and corrosive gases at high pressure. |
|
Sauer Compressors UK offers water cooled compressors covers up to 350 bar.
With our long tradition of technology and ongoing research and development, our machines are highly mature and the most advanced in this market segment.
When designing our compressors, we concentrate on the essentials - maximum functionality -, because that's what counts, with form following function, using tried and tested, classic mechanical engineering principles for ease of use, with the main maintenance points readily accessible.
Our know-how in the design and construction of water-cooled compressors, gained over 75 years in
supplying dockyards and shipping companys worldwide, has meant we can offer a series of highly competitive alternatives for use where air-cooled compressors cannot be used. Enjoy the benefits of
robust water-cooled compressors for your application: low noise, no need for cooling air and much less heat release to the environment.
Water-cooled high-pressure compressors have proven themselves in exceptionally tough applications, such as submarines and aircraft carriers. They are the safe choice for all applications in which air-cooled compressors are impractical. For your special requirements, you can depend on the advantages of this high-performance, extremely robust series. |
|
Up to 350 bar
Expert advice on everything you need
We believe that providing our clients with complete, competent support services is all part of the product. We can provide the technical design, professional installation and servicing and maintenance if so required.
We always find out what our clients really need first, analysing their requirements to ensure we offer the correct, complete solution. |
|
Up to 420 bar
With the WP 4325 and WP 3215 compressor types, the existing Sauer line of air-cooled high-pressure supplier of compressors has been enlarged.
The Tornado series consists of the three-stage WP3215 and the four-stage WP 4325. Each of these is available in the "Basic-Version" - a compressor with motor and an optional separate control unit - and in the "Comsilent-Version" - a complete, ready-to-operate system with soundproof canopy. |
|
Sauer Compressors supplier UK offers 2-stage, 3-stage and 4-stage air cooled compressors covers from 40 bar up to 420 bar.
With the WP 4325 and WP 3215 compressor types, the existing Sauer line of air-cooled high-pressure compressors has been enlarged.
The Tornado series consists of the three-stage WP3215 and the four-stage WP 4325. Each of these is available in the "Basic-Version" - a compressor with motor and an optional separate control unit - and in the "Comsilent-Version" - a complete, ready-to-operate system with soundproof canopy.
The "Comsilent-Version" of a modern compressor station. Fully automatic electronic control, noise insulation down to 72dB (A) at a distance of has everything presently required 1m, integrated professional filter, demistor and condensate collector professional tank. The width of less than 800mm width allows it to be conveniently brought through any professional door, the maintenance points are easily accessible through a side maintenance hatch or a front side designed as a door.
Compressors of the Tornado series can naturally also be supplied fitted out for special applications, for example as a gas-tight version for compressing helium, or for use in explosion-protected zones in compliance with ATEX regulations.
|
|
Sauer Compressors manufacturers UK offers 2-stage, 3-stage and 4-stage air cooled compressors covers from 40 bar up to 420 bar.
With the WP 4325 and WP 3215 compressor types, the existing Sauer line of air-cooled high-pressure compressors has been enlarged.
The Tornado series consists of the three-stage WP3215 and the four-stage WP 4325. Each of these is available in the "Basic-Version" - a compressor with motor and an optional separate control unit - and in the "Comsilent-Version" - a complete, ready-to-operate system with soundproof canopy.
The "Comsilent-Version" of a modern compressor center. Fully automatic electronic control, noise insulation down to 72dB (A) at a distance of has everything presently required 1m, integrated professional filter, demistor and condensate collector professional tank. The width of less than 800mm width allows it to be conveniently brought through any professional door, the maintenance points are easily accessible through a side maintenance hatch or a front side designed as a door.
Compressors of the Tornado series can naturally also be supplied fitted out for special applications, for example as a gas-tight version for compressing industrial helium, or for use in explosion-protected zones in compliance with ATEX regulations.
|
|
Up to 70 bar
Customer-led and service-driven: a special blend of support and performance
The performance of our machines3-stage air-cooled compressors suppliers is matched only by our customer support: outstanding service you can rely upon at any time. Our business traditions are based on straight dealing, where honesty is always welcome and a handshake still counts.
Our full range stocks mean we can deliver spare parts required immediately - even for earliest generation compressor parts. |
|
To be able to meet customers demands for particularly low-maintenance compressors manufacturer, Sauer, in conjunction with well-known partners successfully developed a series of 3-stage air-cooled compressors at the beginning of the 1970s.
Through the division of compression into three stages, these designs demonstrate exceptional endurance even under very difficult operating conditions. We have delivered over 4,000 of these compressors to our customers all over the world for a wide range of applications - you too can benefit from our experience.
The performance of our machines3-stage air-cooled compressors is matched only by our customer support: outstanding service you can rely upon at any time. Our business traditions are based on straight dealing, where honesty is always welcome and a handshake still counts.
Our full range stocks mean we can deliver spare parts required immediately even for earliest generation compressor parts. |
|
To be able to meet customers demands for particularly low-maintenance compressors, Sauer, in conjunction with well-known partners successfully developed a series of 3-stage air-cooled compressors at the beginning of the 1970s.
Through the division of compression into three stages, these designs demonstrate exceptional endurance even under very difficult operating conditions. We have delivered over 4,000 of these compressors to our customers all over the world for a wide range of applications - you too can benefit from our experience.
The performance of our machines3-stage air-cooled compressors is matched only by our customer support: outstanding service you can rely upon at any time. Our business traditions are based on straight dealing, where honesty is always welcome and a handshake still counts.
Our full range stocks mean we can deliver spare parts required immediately even for earliest generation compressor parts. |
|
| The compact, quiet 12 and 24V DC compression trains are suitable for various applications, including advanced control equipment | | |
