|
|
|
|
|
|
* 12 bit transient recorder
* 8 synchronous channels with seperate A/D
* Maximum sampling rate 25 MS/s on 8 channels
* Simultanous sampling on all channels
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 8 input ranges between ±50 mV and ±10 V
* Input offset up to ±100%
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* Synchronous digital channels and ABA mode available as an option
The M2I.31xx series allows recording of two, four or eight channels with sampling rates of 1 MS/s, 10 MS/s or 25 MS/s. Due to the proven design a wide variety of 12 bit A/D converter boards for PCI bus could be offered. These boards are available in several versions and different speed grades making it possible for the user to find an individual solution.
As an option 4 digital inputs per channel could be recorded synchronously. The installed memory of up to 2 GSample will be used for fast data recording. It can completely be used by the currently active channels. If using slower sampling rates the memory is switched to a FIFO buffer and data will be transferred on-line to the PC memory or to hard disk.
|
|
* 16 bit A/D converter board
* 8 synchronous channels with seperate A/D
* Maximum sampling rate 3 MS/s on 8 channels
* Extremely high dynamic range
* Up to 256 MSample memory
* 8 input ranges between ±50 mV and ±10 V
* Continuous FIFO mode
* Automatic offset calibration
* Selectable single-ended or differential inputs
* Synchronisation to multi-board system possible
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.46xx series allows recording of two, four or eight channels with sampling rates of 200 kS/s up to 3 MS/s. These cards offer outstanding A/D features both in resolution and spees for CompactPCI. They are available in several versions and different speed grades making it possible for the user to find an individual solution. The installed memory of up to 256 MSample can be used for fast data recording or sustained data streaming. The enhanced FIFO engine is capable of streaming even 8 channels with 3 MS/s sustained to memory or hard disk.
|
|
* 16 bit A/D converter board
* 8 synchronous channels with seperate A/D
* Maximum sampling rate 1 MS/s on 8 channels
* Extremely high dynamic range
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 8 input ranges between ±50 mV and ±10 V
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* ABA mode available as an option
The M2i.46xx series allows recording of two, four or eight channels with sampling rates of 200 kS/s up to 3 MS/s. These cards offer outstanding A/D features both in resolution and spees for PCI/PCI-X. They are available in several versions and different speed grades making it possible for the user to find an individual solution. The installed memory of up to 2 GSample can be used for fast data recording or sustained data streaming. The enhanced FIFO engine is capable of streaming even 8 channels with 3 MS/s sustained to memory or hard disk.
|
|
|
|
|
|
* 12 bit transient recorder
* 4 synchronous channels with seperate A/D
* Maximum sampling rate 25 MS/s on 4 channels
* Simultanous sampling on all channels
* Up to 64 MSample memory
* 8 input ranges between ±50 mV and ±10 V
* FIFO mode up to 50 MS/s sum samplerate
* Input offset up to ±100%
* Automatic offset calibration
* Synchronisation to multi-board system possible
* 32 Bit PXI / CompactPCI 3U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MX.31xx series allows recording of two or four channels with sampling rates of 1 MS/s, 10 MS/s or 25 MS/s. Due to the proven design a wide variety of 12 bit A/D converter boards for PXI bus could be offered. These boards are available in several versions and different speed grades making it possible for the user to find an individual solution. As an option 4 digital inputs per channel could be recorded synchronously. The installed memory of up to 64 MSample will be used for fast data recording. It can completely be used by the currently active channels. If using slower sampling rates the memory is switched to a FIFO buffer and data will be transferred online to the PC memory or to hard disk.
|
|
|
|
|
|
* Universal digital I/O
* 32 bit data width at 125 MS/s
* configured for input and output
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* 110 Ohm input impedance selectable
* Inputs 3.3 V and 5 V TTL compatible
* Outputs 3.3 V TTL compatible
* Up to 4 GByte on-board memory
* FIFO mode for input and output
* Pattern/edge/pulse width/delay trigger
* Synchronization option available for up to 16 cards
* Options: ABA mode, Multiple Recording/Replay, Gated Sampling/Replay, BaseXIO
The M2i.70xx series of fast digital I/O boards offer a resolution between 1 bit and 64 bit with a maximum sampling rate of 125 MS/s (60 MS/s). All I/O lines of the card can be programmed for either input or output direction. The on-board memory of up to 4 GByte can be used completely for recording or replaying digital data. Alternatively the M2i.70xx can be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several M2i series cards. Therefore the M2i.70xx board can be used as an enlargement to analog boards.
|
|
|
|
|
|
* Universal digital I/O
* 32 bit data width at 125 MS/s
* configured for input and output
* 110 Ohm termination software selectable
* 3,3V and 5V TTL tolerant I/O lines
* Up to 512 MByte on-board memory
* continuous FIFO transfer possible
* Pattern edge pulsewidth trigger
* internal synchronisation with analog cards possible
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.70xx series of fast digital I/O boards offer a resolution between 16 bit and 64 bit with a maximum sampling rate of 125 MS/s (60 MS/s). Every 16 bit / 32 bit of the board could be separately programmed for input or output. The on-board memory of up to 512 MByte could be completely used for recording or replaying digital data. Alternatively the MC.70xx could be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several MC.xxxx boards. Therefore the MC.70xx board could be used as an enlargement to analogue boards.
|
|
* Universal digital I/O
* 16 bit data width at 125 MS/s
* 110 Ohm termination software selectable
* 3,3V and 5V TTL tolerant I/O lines
* Up to 128 MByte on-board memory
* continuous FIFO transfer possible
* Pattern edge pulsewidth trigger
* internal synchronisation with analog cards possible
* 32 Bit PXI / CompactPCI 3U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MX.70xx series of fast digital I/O boards offer a resolution between 16 bit and 32 bit with a maximum sampling rate of 125 MS/s (60 MS/s). The on-board memory of up to 128 MByte could be completely used for recording or replaying digital data. Alternatively the MX.70xx could be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several MX.xxxx boards. Therefore the MX.70xx board could be used as an enlargement to analogue boards.
|
|
|
|
|
|
* Universal digital I/O
* 32 bit data width at 125 MS/s
* configured for input and output
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* 110 Ohm input impedance selectable
* Inputs 3.3 V and 5 V TTL compatible
* Outputs 3.3 V TTL compatible
* Up to 4 GByte on-board memory
* FIFO mode for input and output
* Pattern/edge/pulse width/delay trigger
* Synchronization option available for up to 16 cards
* Options: ABA mode, Multiple Recording/Replay, Gated Sampling/Replay, BaseXIO
The M2i.70xx series of fast digital I/O boards offer a resolution between 1 bit and 64 bit with a maximum sampling rate of 125 MS/s (60 MS/s). All I/O lines of the card can be programmed for either input or output direction. The on-board memory of up to 4 GByte can be used completely for recording or replaying digital data. Alternatively the M2i.70xx can be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several M2i series cards. Therefore the M2i.70xx board can be used as an enlargement to analog boards.
|
|
|
|
|
|
* Universal digital I/O
* 32 bit data width at 125 MS/s
* configured for input and output
* 110 Ohm termination software selectable
* 3,3V and 5V TTL tolerant I/O lines
* Up to 512 MByte on-board memory
* continuous FIFO transfer possible
* Pattern edge pulsewidth trigger
* internal synchronisation with analog cards possible
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.70xx series of fast digital I/O boards offer a resolution between 16 bit and 64 bit with a maximum sampling rate of 125 MS/s (60 MS/s). Every 16 bit / 32 bit of the board could be separately programmed for input or output. The on-board memory of up to 512 MByte could be completely used for recording or replaying digital data. Alternatively the MC.70xx could be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several MC.xxxx boards. Therefore the MC.70xx board could be used as an enlargement to analogue boards.
|
|
* Universal digital I/O
* 16 bit data width at 125 MS/s
* 110 Ohm termination software selectable
* 3,3V and 5V TTL tolerant I/O lines
* Up to 128 MByte on-board memory
* continuous FIFO transfer possible
* Pattern edge pulsewidth trigger
* internal synchronisation with analog cards possible
* 32 Bit PXI / CompactPCI 3U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MX.70xx series of fast digital I/O boards offer a resolution between 16 bit and 32 bit with a maximum sampling rate of 125 MS/s (60 MS/s). The on-board memory of up to 128 MByte could be completely used for recording or replaying digital data. Alternatively the MX.70xx could be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several MX.xxxx boards. Therefore the MX.70xx board could be used as an enlargement to analogue boards.
|
|
|
|
|
|
Solid State Frequency Converter with Models from 62.5 to 750 kVA, Standard 47 to 500 Hz (optional to 800Hz)
Maximize Performance and Versatility and Virtually Eliminate Downtime
Pacific's unique master/slave configuration allows up to ten 62.5 kVA mainframes to be paralleled in the field. Any mainframe may be designated as the master. A failed unit is automatically disconnected from the power grid providing unmatched mission reliability.
Pacific's MS-Series Power Source Systems Feature
-Maximum system reliability
-Rugged, powerful output
-Lower installation cost
-All frequency operation
-Lower maintenance cost
-Facility/test power flexibility
-Unmatched performance/price ratio
-Simple display and diagnostics
-Uninterruptible Power Source configuration (UMS Option) readily available
-Power: 62.5kVA/50kW for each 3060-MS.
-Voltage: 0-120/208, 3 phase. May be loaded either WYE or Delta. Other voltages are available as an option.
-Current:175 Arms per phase continuous. 350Apk per phase for non-linear loads.
-Variable Frequency range of 47-500 Hz, as well as switch selectable fixed frequency operation of 50, 60 or 400 Hz is standard on every model (800Hz optional contact factory for more information).
|
|
| ... products without technical information |
| |
Distinguishing features of the MS-series are consistent modularity, attractive design and straight forward configuration of application-specific service units. Available in three sizes: MS4, MS6, MS12.
• Quick assembly and dismantling
• Safety features integrated as standard
• All compressed air preparation functions in 14 freely combinable individual modules
• Standard combinations available
|
|
MS modular series
From 172 to 15 000 cm³
Up to 450 bar pressure
Up to 390 RPM
Single or multiple displacement
With or without brake
|
|
The Fast Piezo shutter developped by the CEDRAT Groupe in collaboration with EMBL (Dr. Cipriani) is based on standard amplified piezo actuators with a special optical head. It provides a compact and low jitter shutter solution for X ray laser beam.
Max No-load displacement (µm): 400
Dimensions (mm): 18,5*60*44
Unloaded resonance frequency (Hz): 900
Response time (ms): 0,56
Mainly based on the APA concept, the CEDRAT Group has developed different mechanisms in order to fulfill its customers' requests for several degrees of freedom kinematics. These mechanisms take advantages of the APA concept offering a reliable, robust, precise and compact solution to the users.
These Standard mechanisms are currently available in order to meet various needs in terms of kinematics and force
|
|
The Loss of Mains Relay type LMR-111D is for protection of the generator against damage resulting from a non-synchronised reconnection to the grid after a temporary mains failure.
Features include
> Detection of vector shift
> Mains disconnection on mains failure
> Ensures no asynchronous reconnection
> LED indication of fault condition
> LED indication for activated relay
> 35 mm DIN rail or base-mounting
The Loss of Mains Relay type LMR-111D forms part of a complete DEIF series of relays for protection and control generators
|
|
|
With durable, rugged construction, high performance and a design that meets safety standards, the MS/MT350 set the global benchmark for truck-mounted sweeper quality.
|
|
... see all the products in the category
Sweepers
|
|
|
|
|
Orbitform Group's multi-forming heads are used for applications where more than one form is required per powerhead cycle. These multi-forming heads are the solution for wide variety of center distances, number of forms, form sizes and form heights.
Multi-form Head Features:
Orbitform Group's multi-form heads are available in wide range of sizes, capacities, number of forms, form heights and reaches. Features of their reliable and durable construction include:
*Forming capacities ranging from .125" - 1.0" (3.18 - 25.4 mm) finished head diameter (mild steel)
*Number of forming points ranging from 2 - 10
*Center distances ranging from .188" - 12.0" (4.78 - 304.8 mm)
Multi-forming heads provide solutions for application that require more than one form per machine cycle. Each of these heads come with removable peen tools. These peens are available in a wide variety of styles to meet your finished form geometry needs.
Orbitform Group supports our customers with factory trained sales engineers and applications specialists. We have the expertise to deliver the solution for any forming requirements.
|
|
welding machine with high power (medium frequency technology):
- Improved energy efficiency 90% of the market.
- Allows performance, reliability and security.
- Effort tightening up to 550 daN.
- Full cooler liquid.
- Chariot riding stable and balanced.
- Support rotary and vertical mobility.
- Archiving operations and return on a computer.
- Many accessories available.
|
|
Cable glands System UNI Dicht
– boundlessly applicable
The PFLITSCH System UNI® Dicht - is the modern cable gland program for a widely varying range of applications in electrical technology and electronics, machine and plant engineering, installation, traffic and chemical technology.
Gland bodies of various metals and plastics can be combined with sealing inserts of various materials, and therefore adapted precisely to cable diameters and conditions of use.
With UNI Multi several cables can be guided through a perfectly sealed connection. In addition, with UNI Dicht hose cable glandsconnections, cables can also be protected externally in special hoses. e.g. for corrugated pipes or hoses.
Pflitsch contributed actively to drawing up the European standard EN 50262 and continues to set standards through innovations.
Certificates: UL/CSA, VDE, PTB etc.
|
|
| ... products without technical information |
| |
The T-BOX MS remote terminal unit (RTU) combines the power of the Internet with modular-based architecture to create a class-leading remote control and automation solution. Equipped with one of the market’s most powerful processors, only T-BOX incorporates Web server technology with SMS reporting and remote control to give you real-time access anytime, anywhere using a standard web browser.
T-BOX MS features Plug & Go technology, allowing you to distribute your full site configuration on an SD/MMC card. Your maintenance personnel can deploy it without switching on a computer. T-BOX MS features GSM telemetry communications.
|
|
| ... products without technical information |
| |
|
|
