|
|
Dimensions acc. to IEC 60297 or IEEE 1101.1, Aluminum or sheet steel versions, up to superior EMC level. Large selection of assembly options.
|
|
Elma offers AC and DC horizontal enclosures in 2U and 5U heights and a DC-only version in 4U height. They include a wide range of backplane, shelf management,and other options. Pluggable and redundant fan trays, PEMs and shelf managers provide the highest level of availability (99.999%). The units have been optimized via backplane signal integrity studies and chassis thermal simulation.
The 2nd Gen 19" rackmount vertical ATCA chassis is designed for carrier-grade applications. The 13U chassis features a 14 -slot Dual Star or Mesh backplane. The unit is fully pluggable, designed for NEBS compliance, and radial or bussed IPMB shelf management. The chassis has been optimized via thermal simulation studies.
|
|
|
MicroTCA is complementary to PICMG3.0 ATCA. Where AdvancedTCA is optimized for very high capacity and high performance applications, MicroTCA is designed to address cost sensitive and physically smaller applications with lower capacity, performance, and perhaps less stringent availability requirements. MicroTCA preserves many of the important philosophies of AdvancedTCA, including basic interconnect topologies and management structure.
|
|
one cabling solution for your equipment
- Ten sizes of cable ducting plus associated accessories.
- Optimal ducting sizes for maximum cabling capacity.
- Simplified installation:
- snap-off tongues for cable entry,
- 4 types of fixing accessories to suit the application: screw, clip-in, door mounting and chassis mounting.
- Important: no metal component parts enter the inside of the trunking, thus maintaining electrical insulation.
|
|
|
|
|
|
Complete 3 U CompactPCI-based DAQ iPC
This handy complete PC has a CPU which was selected especially for measurement applications: It has power enough for DAQ and control, but leaves out unnecessary features. There are 2 slots for ME CompactPCI boards of your choice. ME-Neuron and the ME-Synapse go together well: The robust housings have the same form factor and can be stacked.
Applications:
* As complete stand-alone DAQ PC for measurement, data acquisition, control, independent realtime operations etc.
* An ethernet DAQ station/networking DAQ PC in the ethernet.
* A control PC for ME-Synapse USB or LAN.
CPU module
* Standard: CPU module of type EKF Calypso in customized version: 3 U/4 HP, LV Pentium M738, 1.4 GHz CPU, FSB 400 MHz, DVI-I, 2x 512 MB DDR (533), 2x GB ethernet, 2x USB 2.0, 2x RS232, 1x PS/2, 40 GB HDD.
* NEW - DUAL: For many applications, eg. with the software SCALE-RT from COSATEQ, a dual core CPU may be recommended - now available with the ME-Neuron DUAL (XL). With a CPU module of type EKF Boogie in customized version: CPU 2.26 GHz Core 2 Duo, 2x 2 GB RAM, HDD 160 GB.
|
|
DC braking with one-way rectification
suitable for all asynchronous motors and for mono phase motors
controlled by microcontroller
easy mounting, also for retrofitting into existing plants
wear-resistant and maintenance-free
integrated braking contactor
printed circuit-board version with fault signalling contact
for snap-on mounting onto 35mm DIN rail
degree of protection: case version IP 20, printed circuit-board version (LP) IP 00
meets trade assoc. requirements for category 2 acc. to EN 954-1 according to the test principles of woodworking machines GS-HO-01 and is already certified
|
|
High power output and flexible desing
Flexible design satisfy all your needs. By the vector control to achieve high start-up power and steady low-speed power easily and afford you the best drive unit.
Easy operation Innovative keyboard design which make it easy to accomplish frequency setting. Convenient to replace the cooling fan. Cnetralize the complex parameter by UP/DOWN. The exerciser which with copy function makes using much more easier.
|
|
... see all the products in the category
AC drives
|
|
|
|
|
The Winchester Rack and Panel product line is one of the most comprehensive pin and socket style connector systems available for cable-to-cable, cable-to-panel, and cable-to-board applications. The extreme versatility of Winchester's Rack and Panel line allows this connector system to be used in a wide variety of industries including industrial, military, aerospace, instrumentation, and telecommunications.
The Rack and Panel product line consists of molded insulators, screw-machined contacts, anodized aluminum hoods and protective shells, and a wide assortment of mating hardware. Other important features of the Rack and Panel product line include:
- Insulators available in a wide range of position sizes depending upon the product series.
- Solder cup, crimp, and dip solder PCB contacts available in pin diameters of .062, .040, .030, and .025 inches with current ratings of 13, 7.5, 5 and 3 Amps.
- Contacts pre-loaded into insulators or sold separately.
- Top or side opening cable hoods for applications requiring 180- or 90-degree cable exit.
- Male plug and female receptacle protective shells help to protect connector interfaces during handling as well as to provide polarization to ensure connectors are mated correctly.
- Wide assortment of mating hardware and accessories including fixed and turnable jackscrews and sockets, guide pins and sockets, mounting plates, and gaskets.
|
|
Elo's iTouch touch-on-tube chassis CRTs are the right choice for your kiosk because they are durable, reliable, sealed, and deliver the ultimate in picture quality.
Typical desktop monitor designs can change without notice every 12 to 18 months, creating havoc for the design and service of kiosks and other enclosed applications. Elo's kiosk CRTs reduce or eliminate the need for redesign by providing a much longer model life than plastic case CRTs. At the same time, they provide the reliability and ruggedness required for operation in a public environment.
Featuring Elo's breakthrough iTouch touch-on-tube technology and no overlay to break, your kiosk will have the best picture quality and vandal resistance possible on a touch CRT. A final benefit is the watertight sealed bezel that adapts the curvature of the CRT face to a flat cabinet front.
|
|
Elo's chassis LCD monitors have a long-lasting product cycle because the enclosure is controlled by Elo's specifications. Future panel improvements are therefore possible without external changes. The monitors are available with multiple touch technologies and all feature a unique, injection-molded minibezel and watertight seal, plus a multitude of mounting options.
Features include:
·Analog and digital (DVI-D) video inputs
·Long lasting product cycle—enclosure controlled by Elo specifications
·Panel upgrades possible to the model in the future without external changes
·Integrated precision minibezel with watertight 0.5 mm seal
·Multiple mounting options including rear-mount, VESA mount, and front/panel-mount bezels or 19" rack-mount bezel
·Serial or USB touch interface
·Multilingual remote on-screen display (OSD)
·Worldwide agency approvals
·3-D electronic design files available
|
|
|
|
