|
|
-The RC Conveyor concrete spreader are used in bridge paving and flat slab paving. It can spread in a width from 3 Mts. to 19 Mts.
-The RC Conveyor place concrete in front of the Paver Finisher by Divertar car. Divertar car speed and travel speed are variable and can be controlled from the operator's station
-Conveyor belt unit used alternatively for bed as well as slope position, with minor alteration in the pin connected bolted structure
-High production capability will spread up to 35 CuMt per hour with constant concrete supply and suitable site condition
-Conveyor with standard flange wheel runs on rail, Travel speed of each end is controlled separately. This negotiate the curves easily
-Special charging hopper to permit feeding of concrete by Transit mixer.
-The conveyor can also run bank to bank on smaller canal with suitable shute to place concrete from the canal height.
|
|
Putzmeister Mörtelmaschinen GmbH is pleased to present one of its most extensive ranges of machines: from the versatile plastering machines, such as our mixer and screw conveyor pumps, to state-of-the-art floor screed conveyors and our small fine plaster spraying and paint pumps, and beyond to our sturdy fine concrete piston pump.
We can provide you with the right machine and suitable accessories for virtually all applications.
Floor screed pumps
for self levelling floor screed and traditional cement screed, for mixing and conveying materials from sand, gravel and cement to pourable and fine concrete.
|
|
TRANSMAT 27.45
DIESEL-POWERED SCREED MIXING AND PUMPING MACHINE WITH BUILT-IN COMPRESSOR
TRANSMAT 27.45 is one of the top models in the range of machines designed for mixing and pumping screeds, insulating mixtures, concrete and aggregates.
|
|
|
|
|
|
The line of IMER Group belt conveyors stands out for the versatility of its applications in the work yard. Our range is made up of LT 1200, LT1500 telescopic and LT1600 telescopic.
The belt conveyors are driven by a hydraulic transmission in vertical position capable of turning 280° around their axis, facilitating their positioning and manoeuvrability, even on uneven ground. During the distribution, the truck must remain parked in the area where it is positioned.
The speed of the conveyor is independent of the vehicle that carries the mixer or of the auxiliary motor, as it is provided by a hydraulic fixed displacement motor connected to the conveyor drive roller, which in turn is driven by a hydraulic pump connected to the power takeoff of the vehicle transmission.
The conveyor structure is made of steel with a high yield point providing the necessary sturdiness and elasticity. The accurate design and the constant attention to the requirements of the end user gives the belt conveyors reliability, and allows easy access to all their parts for cleaning and maintenance.
The conveyor makes it possible to easily and immediately distribute, at the desired point, the material contained in the mixer: concrete, gravel, sand, cement-bound granular material, etc.
The conveyor is ideal in the building of foundations, small floors, and also concrete pillars and road works. It is an ideal means, both in functional terms (flexibility and versatility, even in severe conditions) and in economic terms.
|
|
|
The LTB conveyor belt is the most cost-effective solution for transporting materials such as concrete, sand, crushed stones or pebbles from the truck mixer into the building site.
|
|
Trans MixAir 260/55
The exceptionally gifted one of the conveyer-mixers of cover combines ingeniousness and robustness. The meeting of the Lancy innovation and Brinkmann manufacture.
* Performances Hauls (noncumulable):
O horizontal: 200 m
O vertical: 50 stages
* Maximum flow: up to 20 cycles per hour
* Maximum granulometry (with exit Ø 90: up to 20 mm
* Noise level following European directive THIS 2000/14: 96 dB
|
|
Trans MixAir 200/30
Essential assistant of the craftsman tile-layer, this conveyer-mixer will allow you to associate speed, quality and profitability for the realization of your covers.
* Performances Hauls (noncumulable):
O horizontal: 100 m
O vertical: 15 stages
* Maximum flow with cone: 3m3/h
* Maximum flow with skip: 4m3/h
* Maximum granulometry (rolled aggregates): 15 mm
* Noise level at the work station: < 85 dB
* Sound power: < 100 LWA
|
|
MINI AVANT
PLASTERING AND CONVEYING MACHINE FOR COMMON AND SPECIAL MORTARS
MINI AVANT is the ideal solution for pumping, conveying and applying a wide range of common mortars, lime and/or cement-based mortars and cement-based ready-mixed plasters.
|
|
| ... products without technical information |
| |
Automatically remove and elevate ferrous materials such as chips, turnings and small parts. Conveyor mechanism is totally enclosed. Wide variety of configurations can be assembled from standard design sections.
Chip & Parts Conveyor - Standard Utility Model 68
Standard model for lightweight material.
Chip & Parts Conveyors - Low Profile Permanent Magnetic
Control lightweight ferrous materials.
Chip & Parts Conveyors - Model 6
6-1/4 in. (159mm) deep housing to transport small volumes of chips.
Chip & Parts Conveyors - Model 9
9-1/4 in. (235mm) depth for greater volumes.
Chip & Parts Conveyors - Model 12
12-1/4 inch (311mm) depth for high volumes of chips.
Chip & Parts Conveyors - Model 21
21-1/4 in. (540mm) working width for high volume conveying.
|
|
The conveyor Turbo Magnetic is specially designed for Multi-tasking machines producing fine chips of ferrous material. The Turbo Magnetic features a heavy gauge stainless steel slider face for a long life in extreme wear conditions. All moving parts are contained inside the conveyor’s viton sealed frame so they are never exposed to machining contaminates. The conveyor belt is automatically tensioned.
Self-lubricated Track
No lubrication oil inside the conveyor to leak and contaminate the coolant.
Reduced Coolant Carry-out
A variable speed drive (AC Inverter) is standard on all units to maximize chip removal and minimize coolant loss.
Easily-Replaceable Magnets
Turbo components, including individual magnet segments, are easily and economically replaced if the conveyor is accidentally damaged.
|
|
Magnetic conveyor M
Areas of application
Transportation of short ferromagnetic, emulsion-afflicted shavings and small parts, e.g. stampings. Installation possible as individual conveyor or interlinked system.
Function
A continuous magnetic band conveyor, consisting of two chain strands which have been connected by means of carrying strips and permanent magnets, continuously conveys the material to be conveyed on the conveyor plate to the discharge station. Pre-cleaning of the cooling lubricant without additional cleaning elements. The magnetic band drive occurs via a three-phase geared motor. The magnetic band has been installed self-tight eningly.
|
|
|
Applied Recovery Systems can design a variety of steel belt conveyors and steel belt conveyor systems to meet the demands of your chip processing system. Whether your metal chip processing requires a simple take away system for briquettes, or a more complex system for conveying chips and cutting oils from machine tools, Applied Recovery Systems will meet your needs.
|
|
|
|
|
|
Heavy-Duty Magnetic Conveyors - For dependable, maintenance-free, positive transfer of ferrous metal scrap and parts with no carryover.
Features, Benefits, & Options:
- Conveys wet or dry ferrous chips, stamping slugs, stamping scrap, or parts
- Rugged, long life stainless steel slider bed
- Available in straight, L-style, or Z-style configurations
- Alloy steel bar tracks, precisely guide chain and magnetic assemblies
- Self adjusting drive chain take-ups
- Completely sealed, oil tight construction for quiet self-lubricating performance
- Available with permanent ceramic or optional rare earth magnets
- Extended height elevation and pivoting conveyors (to be inserted into your press) are also available
--------------------------------------------------------------------------------
Standard Duty Magnetic Conveyors - Low profile - Only 3 3/8 inch high! An economical alternative for less demanding applications. For dependable, maintenance free, positive transfer of ferrous scrap and parts with no carryover.
Features, Benefits, & Options:
- Conveys wet or dry ferrous chips, stamping slugs, stamping scrap, or parts
- Rugged, long life stainless steel slider bed
- Available in straight, L-style, or Z-style configurations
- Features a steel encased UHMW low friction track
- Quiet, self lubricating performance
- Supplied with permanent ceramic magnets
|
|
|
|
|
|
Bunting MagSlide® Magnetic Slide Chip and Parts Conveyors are built to handle the tough jobs. Dirty, oily parts, jagged, abrasive scrap, and other punishing materials that could damage or jam conventional conveyors are no challenge for Bunting's 3-D CAD-designed, ruggedly constructed slide plate conveyors. They are ideal for use anywhere you need to transfer ferrous chips, turnings, and small parts from lathes, mills, or stamping presses or from slitting, forming, and other metalworking operations. Chain-driven, permanently charged high-energy Ceramic magnets inside the conveyor housing attract and move ferrous material along the conveyor's stainless steel faceplate. Optional water-tight housings can be submerged into almost any type of hot or cold liquid.
MagSlide Conveyors are engineered for trouble-free, virtually maintenance-free operation. There's no external belt to jam, tear, or wear out from carrying sharp, abrasive parts and scrap.
Get Outstanding Performance and Value
- Rugged construction
- Continuous chain lubrication with oil-impregnated UHMWPE SlideTrack™
- Oil ports to allow extended chain service
- High-energy Ceramic or Rare Earth Magnets matched to your application
- Durable stainless steel slider beds
- Sealed precision drive and take-up bearings
- Designed with 3-D solid-model technology
- Precision manufactured on CNC machines
- Optional submersible housings
|
|
| ... products without technical information |
| |
Conveyors
SGB420
These conveyors a set of new products designed and developed by our company convey coal for coal faces of blest mining and gateways in gently inclined thin and medium thickness seams of small and medium size mines.
|
|
Heavy scraper conveyors
- Longwall scraper conveyors PSZ-750.
- Longwall scraper conveyors PSZ-850.
- Longwall scraper conveyors PSZ-1100 (1200).
- Beam stage loaders GSW.
- Beam stage loaders PP.
- Gallery conveyors PZ-1000.
|
|
SLK 4.2
Transfer conveyor as a flexible link between roadheader and haulage system.
Cut material can be transfered directly into shuttle cars, mine cars or on section conveyors. Alternatively the discharge ending can be linked directly with a bridge belt conveyor which rides on the main or seciton conveying system.
|
|
|
|
|
|
Function
These units are based around a twin belted conveyor segment with one adjustable and one fixed side. The frame consists of four adjustable feet, an integrated switching
cabinet and a table construction to support the conveyor mechanism. The transfer of the PCB’s can be clocked or synchronous.
Special features
- Speed of conveyer segment automatically adjustable or
adjustable through the configuration
- Control mode with display of control frequency and
current counter reading
- Control status can be limited using timeout
- Adjustable print control (optional)
(time to monitor the transfer from the previous unit e.g. screen printer)
- Optimal adaptation of the working panel possible (from
length 1000 mm)
- Mounting holes for foot rest and lamp holders are
standard in the series
- Closed leg construction
- Programmable adjustment of the observation point
- Same software used for 1 - 4 segment units
- Input interface can be blocked at the push of a button
(Function if line is to run empty)
- Buffer function on the conveyor can be switched off
- Different conveyor lengths possible
- 2/1 mode
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
see the results for the following category : 
