|
|
The Reovib BK032 is a monitoring unit for vibratory feeders. By using this measuring device in conjunction with an accelerometer e.g. Reovib SW10, vibration levels can be monitored. An acceptance window can be set defining adjustable maximum and minimum limits. If either of these values are exceeded then a corresponding relay will operate. During the unstable, start-up phase a time delay can be set so that spurious readings are ignored. The unit has a built-in sensor power supply available for direct connection. A 4...20mA signal can be used instead of an accelerometer.
|
|
|
|
|
|
The DT9837A is a highly accurate USB data acquisition module that is ideally suited for portable noise and vibration measurement and analysis. Four 24-bit IEPE (ICP) sensor inputs are synchronized with a tachometer input to provide data streams that are matched in time for field or laboratory use. A read-back channel from the analog output guarantees perfect correlation of all signals in the input stream, the output stream, and the tachometer.
This rugged small module is self powered via the USB connection to a PC or laptop, no external power supply is needed. This makes it ideal for portable measurement applications. Additionally, two modules can be triggered simultaneously for perfectly synched measurements over eight inputs.
The DT9837A ships with a software applet to get you up and running right out-of-the-box. This applet supports basic operation of the module and can be easily modified for more advanced capabilities using Measure Foundry®, our popular rapid application builder software.
|
|
|
|
|
|
600 Series
Dynamic Signal Analyzer (DSA)
Vibration data acquisition, analysis, and monitoring has never been easier than with the new IOtech 600 Series of dynamic signal analyzers and eZ-Series software. More than 30 years of engineering experience in vibration measurements have gone into the design of the 600 Series of DSAs.
Key Highlights
• Analysis frequency ranges are software programmable from 20 Hz to 40 kHz
• 24-bit Sigma Delta ADC per analog input
• Spurious-free dynamic range of 108 dB (typical)
• AC/DC coupling, software selectable per channel
• TEDS support for accelerometers
• Pseudo-differential input
• Total harmonic distortion of -100 dB (typical)
• Channel-to-channel phase matching of <0.12 degrees at 1 kHz
• 8-bit digital IO port
• USB 2.0 high-speed
640 Models
• 4 analog inputs, ±10V input range (±60V max without damage)
• 2.1 mA IEPE current source per channel (20V compliance)
• 1.0 Hz AC Coupling HPF
• 24-bit Sigma Delta DAC analog output
• Analog outputs: sine, swept sine, random, burst, arbitrary
• Analog output signal-to-noise ratio: 100 dB (typical)
650 Models
• 5 analog inputs, ±40V input range (±60V max without damage)
• 2.1 mA IEPE current source per channels 1-4 (20V compliance)
• 0.1 Hz AC coupling HPF
|
|
|
|
|
|
TopMessage and TopLab are similar devices and differ only in construction design. TopMessage is designed as a rail mounted device. Signals are connected via clamps.
Message devices can be easily integrated into existing company networks via its Ethernet interface. This means anybody within the network can have access to measurement data using their existing PCs.
Delphin's modular Message devices enables the acquisition of any physical values (e.g. temperatures, pressures, flows, vibration data). Measurement values are stored in the devices already scaled and lineated (e.g. bar, liter/sec, m/min, °C etc.). The scaling of thermocouples and RTD sensors are pre-configured.
A device comprises of 1 or 2 I/O modules which can be combined in any way required. Extension devices can be connected to the basic device, each also having 2 I/O modules. This means Message devices are suitable for both small and large applications.
Each analog input can be separately connected with RTD, thermocouple, volt or 20 mA signals. Expensive measuring transducers are no longer required and potential isolation means there is no need for isolating amplifiers. All I/O module analog inputs are set up as differential inputs.
|
|
|
Snapshot IS provides intrinsically safe data collection / analysis in a convenient, palm-sized package weighing just 1.5 lbs. (680 grams). With both a phase input and a dynamic signal input, it is the industry's only data collector in this size/weight range that boasts both intrinsically safe operation and the ability to capture not just static readings but waveforms, vectors (for balancing and diagnostics), phase information, and spectra. The instrument uses the Microsoft* Windows* CE operating system, is fully compatible with our System 1® software, and features a user interface consistent with that of its larger 2-channel counterpart, Snapshot CE.
|
|
|
FastTracer is an innovative portable triaxial vibration measurement and analysis solution, ideal to be used in different fields of applications such as predictive and routine maintenance, testing, structural analysis, support to research and development, diagnostics, technical assistance and didactics.
|
|
CF-4220Z - Personal FFT Analyzer
A user friendly instrument that brings the power of FFT analysis within easy reach.
Features:
- Compact, ergonomic design and light weight.
- Easy to read 6.4" LCD
- 20 kHz real-time rate.
- Frequency zoom analysis.
- Built-in sensor power.
- Built-in 3.5" disk drive.
Specifications:
- Number of Input Channels: 1
- Frequency Range: 1 to 40 kHz
- A/D Converter: 16-Bit
- Dynamic Range: 85 dB
- Current Sensor Power: 2 mA
- Operating Temperature: 0 to 40º C
- Dimensions: 200 mm (W) x 292 mm (H) x 396 mm (D)
- Weight: Approximately 5.2 kg
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 