|
|
ET24x series surface temperature sensors are intended for measuring
temperatures on closed pipe systems or other round or flat surfaces.
The sensor can be conveniently fixed with a hose clamp or M3 screw.
Mounting with hose clamps avoids any mechanical preparation of the
measurement site.
- For measuring temperatures from -50 to +500 ° C
- Pt100, Pt500, Pt1000, PTC1000 or NTC resistance sensors
- Double RTD sensing element option
- Available in 2-, 3- or 4-wire circuit
- PVC-, silicone,- teflon- or fiberglass-insulated cable
- Quick and easy installation
|
|
Install these compact sensors anywhere for accurate point sensing and fast response. All Thermal-Tab modules use a thin-film RTD element. All Thermal-Ribbon models conform to EN60751 Class B tolerance when ordered with a PD platinum element.
- Fast response surface sensing in aerospace, medical and industrial devices
- Rugged lamination construction
- Polyimide, silicone rubber or Mylar™ insulation
|
|
HM 5040 Magnetic Surface Sensor
Magnetic surface Pt 100 sensor
Size 39x26x25 mm (LxBxH)
Magnetic strength 90 N
Accuracy to DIN IEC 60751 class B.
Optional accuracy class A
Silicone cable length 4 meter.
Good chemical resistance.
Can be used on feretic surfaces
Maximum temperature at tip 250°C
Spring-loaded sensitive contact tip.
|
|
Magnetic surface thermocouple
Magnetic surface probe
Calibration Type K.
Measures surface temperature of ferrous materials such as bearings on induction heaters.
Magnet diameter Ø 14mm.
Response time 7 sec.
Maximum temperature at tip 220°C
|
|
Surface temperature feeler
Designation - measuring range - Messunsicherheit
Oberflächenfühler1 - 0... +60 °C - <20 mK
Oberflächenfühler2 - 0... +60 °C - <50 mK
|
|
The BetaCURVE Chip is Soldered to 30 AWG Solid Silver Plated Nickel Leads with Black Kynar Insulation. Device is Encapsulated in Epoxy Resin.
Features:
5K to 1M Ohms Resistance @25ºC
Climatic Category (IEC 60068-1) 40/125/56
Proven Stability and Reliability
Kynar Insulated Lead Wires
Rapid Time Response
30 AWG Solid Silver Plated Nickel Leads with Black Kynar Insulation
RoHS Compliant
|
|
Measurement Specialties’ glass encapsulated thermistor components are ideal for accurate and reliable temperature measurement, control, or calibration applications.
Available in a range of resistance curves and tolerances.
Temperature Sensor - Radial Glass NTC Thermistors Series A
Features:
- 2K to 500K Ohms Resistance @25ºC
- Hermetically Sealed Package
- High Temperature Stability
- Available in ±1%, ±2%, ±3% or ±5% Tolerance @25ºC
- Glass Encapsulation
- Temperature Range -40ºC to +250ºC
- Low Cost
- RoHS Compliant
|
|
Measurement Specialties offers a wide range of standard and customized instrumentation probe assemblies suitable for the instrumentation industry.
Examples include:
- Surface probes
- Air/Gas probes
- Screw-in probes
- Immersion probes
The products are available in a range of resistance/temperature (R/T) curves, electrical tolerances, and mechanical housings.
|
|
Ni1000SOT is a nickel thin film resistance temperature detector (RTD) that is suitable for use in contact temperature sensing. The devices are manufactured by PVD-deposition on a silicon substrate. The thin film structure is covered by a passivation layer for environmental protection and enhanced stability. The nickel elements are mounted on lead frames and encapsulated in SOT23 packages. This technology allows the production of miniature, low cost, high precision temperature sensors. The characteristics of the temperature sensor comply with the former DIN 43760 standard. It is qualified for the most demanding automotive applications (incl. exposure to hot oil) and is suitable for many more applications in harsh environments.
Features:
- Contact temperature sensing
- Comply with former DIN 43760 standard
- Small SMD package SOT 23
- Automotive qualified
|
|
| ... products without technical information |
| |
|
Kanomax anemometers can measure a wide variety of parameters to test ventilation rate. The parameters include air velocity, airflow, static pressure, temperature, and humidity of the indoor environment.
|
|
|
|
|
|
Specially developed for the supervision of clean-rooms, the CPE 300 is dedicated to measures of low pressure andor depression of air or neutral gases from 0/+10 Pa to -1000 /+1000 Pa.
The CPE 300 presents the advantage to become integrated perfectly into walls and to answer to the standard of cleanliness thanks to its stainless case (brushed or with lacquered).
It is equipped with 2 visual and audible alarms, with 2 reversers relays, of a big electroluminescent display and a process of autocalibration which guarantees in the time an excellent stability and a reliability of the measure in low as in high scale.
Thanks to its digital communication (RS 232 and Protocol Modbus RS 485), it offers the possibility of showing alternately (in addition of the measure of pressure) two other parameters resulting from temperature, humidity, velocity or airflow external sensors (KIMO).
Two innovative systems to facilitate the maintenance on-site :
· Its measuring element benefits from the SMART PRO system. It is individually adjusted and is automatically recognized by the device. Thanks to this process, it is possible to replace the measuring element in a simple and fast way without return of the sensor to the factory.
· The calibration in front face : this system allows to proceed to the calibration of the device without un-mounting it.
The sensor CPE 300 is so always operational !
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
Measurement Specialties’ surface mounted device (SMD) pressure sensors are intended for high volume applications where small size, light weight, and low cost are needed. These pressure sensors are offered in a plastic tube, or metal ring with an optional gel fill. Uncompensated mV, 16-bit digital, and room calibration outputs are available.
Pressure Sensor - Model 1471
Description: The Model 1471 is a piezoresistive silicon pressure sensor, calibrated at room temperature. Packaged in a surface mount configuration, it is intended for high volume applications where small size, light weight, low cost, and compatibility with automated assembly equipment are required. The pressure sensor is available with a gage or absolute pressure sensing chip that is attached to a surface mountable ceramic substrate. A cap is attached to the ceramic substrate, protecting the chip and providing the pressure port. The devices are shipped in plastic antistatic shipping tubes for use with automated production equipment. Caps are also available with a narrow hole or a large hole to interface with the pressure media.
|
|
|
|
|
|
|
The ARES Series is a small, low cost pressure transducer which is able to measure pressures as low as 0 to 5 inches of water, 0 to 10 inches of water, 0 to 15 inches of water, and 0 to 1 psi. Sensitivity to extremely low pressures combined with the small physical size make this device ideally suited for applications such as HVAC, medical equipment, and flow monitoring. The GA100 series has a 4V span from 0.50V to 4.50V and the GA200 series has a 3.75V span from 0.25V to 4.00V. The plastic housing design for the ARES Series makes the device very user friendly. The housing is designed to be printed circuit board mountable, requiring no additional hardware. Built into the housing are self-locking pins which insure a secure fit between the housing and the PCB. The pressure ports are 3/16" barbed ports which mate with industry standard 1/8" or 3/16" ID tubing. These ports are mounted 90° to the printed circuit board to allow other boards to be located above the sensor. The ARES Series utilizes a unique sensor circuit design to provide ASIC digital error correction and signal amplification while maintaining an analog signal path. This technique delivers the high level of error correction associated with microprocessor-based circuits, while maintaining a typical bandwidth of >1 kHz generally found only in analog circuits. The result is a pressure sensor that offers the ultimate in low cost and high accuracy, while preserving the fast response and smooth output inherent to silicon sensors.
|
|
The MS7201-A2 is an absolute silicon micro-machined pressure sensor for harsh environment, with the pads on one side. A vacuum reference cavity is sealed on top of the sensitive silicon membrane by the anodic bonding of a glass cap. The pressure, applied on the backside, is converted in electrical signal by piezo-resistors implanted in the silicon membrane. To improve the sensor stability, a drilled glass is bonded on the backside. As the pressure port consists of glass and silicon, both stable in most of the chemicals, the MS7201-A2 is suitable for media-resistive applications.
Features:
- Media resistive pressure sensor die
- Typical output Span 110mV @ 5V
- Temperature range -40°C to +150°C
- Linearity 0.15% (typical)
- Die size 1.35 x 1.79mm²
- Low cost, high reliability & stability
|
|
|
The MS5535C is a SMD-hybrid device including a piezoresistive pressure sensor and an ADC-Interface IC. It provides a 16-bit data word from a pressure and temperature dependent voltage. Additionally the module contains 6 readable coefficients for a highly accurate software calibration of the sensor. MS5535C is a low power, low voltage device with automatic power down (ON/OFF) switching. A 3-wire interface is used for all communications with a microcontroller. The MS5535C is fully software compatible to the previous versions (MS5535A and MS5535B). Compared to the previous versions, the ESD sensitivity has been improved to 4kV on all pins.
|
|
The P571 pressure sensor is a high stability, small diameter, stainless steel pressure sensor intended for use in pressure transducers and other OEM pressure measurement applications. Its thin-film metal strain gauge circuit enables a long-term stability of better than 0.1% per year. Options include Hastelloy, 500 Vac insulation resistance, integral sputtered thin-film RTD, as well as various optional specifications on TC Zero and TC Span.
The unique design can be used with an infinite variety of pressure fittings, which can be supplied by SMD or provided by the customer. Ideal for pressure transducers and transmitters as well as other pressure measurement applications including process control, hydraulic systems, general industrial, down-hole, pressure calibrators, Cenelec applications, aerospace, automotive and more.
|
|
Measurement Specialties’ TO-5 and TO-8 package pressure sensors are calibrated, temperature compensated at 1.5mA, and mounted on a metal TO header. Our TO Package pressure sensors utilize piezoresistive silicon MEMS technology making them suitable for applications that use non-corrosive dry gases. We offer these sensors in a variety of tube configurations.
The Model 50 is a piezoresistive silicon pressure sensor packaged in a T0-5 configuration. This is offered in a nickel can without a tube. Pressure can be applied on top of the package. Absolute pressure ranges from 0-5psi to 0-500psi are available. The pressure media is applied to the circuit side of the chip. This design is intended for non-corrosive gases and is not recommended for liquids. A gel filling can be applied to provide mild protection against humidity and dust. For high volume gage applications, contact the factory.
|
|
|
|
|
|
Measurement Specialties oil-filled stainless steel pressure sensors are suitable for use in harsh environments of liquids or gases. Many feature proprietary UltrastableTM piezoresistive silicon die technology for long-term reliability.
The Model 154N Low Pressure is a 19mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The Model 154N Low Pressure is designed for o-ring mounting and OEM applications requiring compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. The Model 154N Low Pressure is designed for high performance, low pressure applications. A ceramic substrate is attached to the package that contains laser-trimmed resistors for temperature compensation and offset correction. An additional laser-trimmed resistor is included which can be used to adjust an external differential amplifier and provide span interchangeability to within ±1%. Please refer to the Model 154N UltraStable™ datasheet for information on products with operating pressures greater than 5psi.
|
|
|
|
|
|
Measurement Specialties is an industry leader for the breadth and quality of its pressure sensors, which include pressure transmitter components and pressure transducers. Using multiple technologies, we offer a range of pressure sensors that can measure from inches of water up to pressure transducers that can measure greater than 30,000 PSI. Measurement Specialties pressure sensors are used for a range of diverse applications in industries such as medical, aerospace, transportation, general industry, and test and instrumentation. Pressure sensors can also be delivered as a MEMS silicon pressure die for very small embedded applications.
Dual In-Line Pressure Sensors
Measurement Specialties’ dual in-line pressure sensors are calibrated, temperature compensated, and mounted on a reliable ceramic substrate in an industry standard 0.600 inch lead spacing. These sensors utilize piezoresistive silicon MEMS technology making them suitable for applications that use non-corrosive dry gases. Pressure ports are offered in metal tubes or ceramic barbed ports.
|
|
|
SMD’s Peerless engineering team designs sensors for unique requirements and aggressive cost targets. Typical specialized requirements include small sizes, high temperature, low capacities, “Cenelec” dielectric, and overload proof sensors.
|
|
|
|
|
|
Measurement Specialties produces a broad range of amplified output pressure transducers for everything from high volume OEM use to high accuracy applications.
Our proprietary Microfused™ pressure transducers are designed for OEM applications that require high reliability in harsh conditions.
Measurement Specialties' high performance line includes:
- Ultrastable™ transducers for instrumentation
- Foil strain gage transducers for severe environments
- Miniature transducers used for automotive and aerospace testing
Pressure Sensor - Model EPRB-3
Description: Ultra Miniature Pressure Transducer with platinum RTD to sense media temperature, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are required.
Features:
- Pressure Transducer with Platinum RTD
- Miniature Design (body ø12 mm)
- Any liquid or gas media compatible with Stainless Steel
- Operating Temperature up to 150°C (300°F)
- Rugged for Severe Environment
- CE Approved
- Pressure and Temperature measurement
- Pressure Port M8x1 or 5/16-24 UNF
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
