|
|
|
|
|
|
BL 931700 mini pH controller has been designed for easy, affordable installation in tight spaces to perform simple yet effective process control. As a result of its compact size, BL 931700 can be installed right next to tanks or vats.
This versatile controller is ideal for a wide variety of applications, such as textiles, papers, photographic solutions, plating baths, chemicals and water treatment.
BL 931700 is provided with a selectable setpoint for acid or basic dosage. Measurements are directly acquired from a pH electrode in the range from 0 to 14 with a 0.01 pH resolution. Accuracy is ensured by the 2 point calibration, performed manually through trimmers on the front panel. You can also choose automatic or manual dosing mode with a switch on front panel. Manual control is particularly useful during maintenance operations, because it permits you to enable or disable the dosing relay according to your need.
The overtime control system advises you when the relay is active too long, helping to prevent overdosing. In addition, this model features a 4-20 mA analog output for recorder connection.
Two models are available, with different power supply input at 115/230 Vac or 12 Vdc.
|
|
The oil management system controls the oil level in the compressor crankcase. The system consists of the following ESK-components:
• ESK – Oil Separators
• ESK – Reservoir
• ESK – Oil Level regulators
• ESK – Pressure Valve
• ESK – Strainers
The oil carried over by a compressor in parallel systems has to be returned in the same quantity under all operating conditions. ESK-Oil management systems provide this control and work reliable.
Oil management systems are essential to control oil level if different compressor models are equipped in one a refrigeration system.
|
|
The components presented here have been developed and optimised for increased requirements in close co-operation with our customers over a period of several years. ifm electronic now supplies a sophisticated control and automation system which conforms to the needs of the market. In addition to flexibility and performance attention was given to the following points:
> Operation at extremes of temperature, both high and low.
> The ability to withstand extreme shock and vibrational stresses.
> Use even with direct exposure to dirt, water and moisture.
> Insensitive to supply voltage fluctuations caused by the battery/generator systems.
> The electrical system must be insensitive to high levels of conducted and radiated interference.
> Application-related networking possible with the serial CAN bus suitable for mobile applications.
|
|
CB02N/CB02P :
These circuit boards are used to drive and protect brushless motorized rollers.
Motor torque depends on the speed variation required
Functions:
- Motor Run/Stop
- Selection of the direction of rotation of the motor
- Stopping with dynamic brake
- Error signal
- Variable speed
- NPN logic with CB02N / PNP logic with CB02P
|
|
The Universal Power Cell uses Hall Effect sensors that are not affected by odd waveshapes or frequencies. Also, no Voltage or Current Transformers are used.
The UPC is field scalable to match your pump motor. Complete information at loadcontrols.com.
The PMP-25V Pump Load Control takes the 0-10 volt load signal from the UPC, displays the Pump Load, and has the Set Points, Timers and Relay and Analog Outputs.
|
|
PROCUT is a new Guillotine Control System for paper cutting machines running over our PCM2 Motion Controller. It takes great advantage of new technology in motion control, making all the movements as accurate as possible. PROCUT is a complete system so you will be up and running quickly. The accuracy and friendly user interface helps you obtain great results again and again.
Main features:
* Easy to install and use
* Improve production
* Improve quality of final product
* Memory capacity for 100 programs up to 1000 lines each
* Graphic Colour LCD Screen - 320 x 240 Pixels
* Automatic push out of paper: to help the operator to handle the paper
* Air table control
* Label Optimisation Mode
* Quick cut mode
* ‘Teach’ mode programming
* Loop quantity programmable
* Encoder Feedback
* Imperial and metric
|
|
The CoMo Injection process monitoring system Type 2869A allows zero-defect injection molding production by analyzing the cavity pressure curve.
A bright 12.1" color touch screen monitor Type 5629A3 makes operation of the CoMo Injection system even quicker and easier, and accelerates communication with the system. The new IP Setup Program now being supplied with the system allows simple automatic detection and configuration of CoMo Injection units installed in production.
Version 2.0 of CoMo-MIS Type 2829A…, the database system for storing measured and calculated process data, is now also available in the four languages mentioned above.
All of the CoMo Injection and CoMo-MIS systems that have already been installed can be updated with the latest version. The IP Setup Program works with all CoMo Injection units equipped with Version 1.2.
|
|
|
|
|
|
The CoMo Logic is a y(t) control monitor with three real-time thresholds and elementary post-cycle curve analysis function. The following operating modes are available: 'GRAPHIC’ for displaying the y(t) signal characteristics, ‘TREND’ for displaying the last 118 peaks of the cycle and ‘PEAK’ with numerical display of the cycle peak.
By their web server functionality, CoMo Net and CoMo View are directly connected to the TCP/IP world. Many functions and information can be operated and viewed via familiar browser functions from any point worldwide, of course protected by security precautions and access authorization. A central storage of quality data from larger, complex production lines is significantly simplified and a cost advantageby use of an existing network structure . Also remote maintenance and diagnosis enable fast, qualified and cost-effective on-site help during servicing.
The dependent measurands, for example press force and displacement are recorded and their functional dependence is evaluated. The evaluation result can reject bad parts for reworking or classify production into different tolerance classes.
The CoMo View is equipped with an integrated 5,7" Touch Color-Display of 320x240 pixels. Possible connection of piezo, strain gauge and voltage output sensors as well as potentiometric displacement and angle sensors make this two channel control monitor versatile for most any application. Real-time capability is given via digital I/Os and a fast export of process data and measured curves add significantly to a safe process monitoring even at high cycle rates.
|
|
|
|
|
|
Full Range Supplier
- YORK manufactures a full range of microprocessor and PLC-based control systems for operation and safety control
- Panels can be unit-mounted or free-standing, and are housed in carbon steel, stainless steel, or fiberglass enclosures
- All Panels are built in our UL508 shop and designed for the harshest environments, including hazardous area classifications. Built to NEC or IEC requirements to suit your needs around the world
- Single-source supply of controls with your process equipment ensures trouble-free commissioning and long term parts and service support
Quantum™
- Powered by a Pentium-class processor
- Continuous monitoring of critical system parameters
- Maintains desired operating conditions
- Protects the health of your equipment investment
- Quantum technology means local operator control
- Supports industry-standard, communication interface protocols, including:
Modicon Modbus ASCII serial
Allen-Bradley DF-1 serial
YORK Refrigeration/Frick ASCII serial
YORK ISN
Custom PLC Panels
- YORK builds custom-designed PLC (programmable logic controller) panels for both centrifugal and screw compressor systems
- A typical foundation uses Allen-Bradley ControlLogix, SLC500, or PLC5 Series PLC and hardware
- The PLC's are often combined with Bently-Nevada vibration and temperature monitoring systems, as well as centrifugal compressor anti-surge systems
- Extreme outdoor environments are no problem for YORK custom PLC panels
- They can be designed to ship loose for remote location in a control room
|
|
Generator Paralleling Controller – GPC-2
Compact all-in-one control unit designed for applications programmed in a PLC. The GPC-2 contains all necessary functions for protection and control of a synchronous/asynchronous generator along with all necessary galvanically separated 3-phase measuring circuits.
The GPC-2 is intended for land-based applications. It is designed for the following applications (can be combined):
> Stand-alone
> Parallel with other generators
> Parallel with the mains
The GPC-2 can synchronise the generator and after synchronisation carry out all necessary generator control and protective functions. It is well-suited for PLC-controlled systems and the interfacing can be done via binary and analogue I/Os or via (optional) serial communication.
|
|
Generator Paralleling Controller – GPC-2
Compact all-in-one control unit designed for applications programmed in a PLC. The GPC-2 contains all necessary functions for protection and control of a synchronous/asynchronous generator along with all necessary galvanically separated 3-phase measuring circuits.
The GPC-2 is intended for land-based applications. It is designed for the following applications (can be combined):
> Stand-alone
> Parallel with other generators
> Parallel with the mains
The GPC-2 can synchronise the generator and after synchronisation carry out all necessary generator control and protective functions. It is well-suited for PLC-controlled systems and the interfacing can be done via binary and analogue I/Os or via (optional) serial communication.
|
|
LX display has contemporary graphics that are easy to read and navigate, just like the web
For today's personal computer user, the look and feel of Quantum LX is second nature.
The graphical interface is perfect for your newest users, while our advanced interface has detail to satisfy even your most experienced operator.
|
|
At ITT Water & Wastewater we produce practical and easy to use monitoring and control systems for many different pump and mixer applications. Our systems offer reduced operational costs, total overview, less report handling and better environmental control.
As well as supplying the hardware, such as pump controllers, sensors, electrical start equipment and cables, we also have software for running the system. The ITT Water & Wastewater AquaView SCADA system provides precise and effective monitoring and control.
Each control system comes with a host of well-thought-out functions. Good examples are comprehensive pump control functionality, advanced supervision of pump condition, accurate flow calculation and cleaning functionality. All functionalities are based on international experience in municipal wastewater.
|
|
|
|
|
|
|
VM20 is a modular, multipurpose measuring and test system for grinding machines easily programmable by the user. Available as independent unit or for rack-mounting, equipped with local hardware or remote operator panel as well as with Windows Software panel, digital I/O logic interfaces, Profibus and RS232. The wide range of grinding wheels balancing devices, with or without embedded acoustic sensors, applicable on single or multiple grinding wheels or long grinding wheels, allow to automatically and rapidly reduce vibrations which generally cause errors and imperfections on worked surfaces. The wide range of AE transducers configuration available, with assembly both on rotating and stationary machine components, can be used to monitor the machine conditions, through FFT analysis, and to determine the grinding wheel position when it contacts the piece to be worked or the tool-dresser. During working, diameter and roundness gauges, as well as the pieces positioning gauges, allow to achieve a constant production quality together with a cycle time improvement, thanks to correct feeding speeds for roughing-out and finishing.
|
|
Modern automation, control and remote control systems have become essential for optimized and secure control and monitoring of processes regarding energy distribution and industrial networks.
Depending on the specific field of application, different requirements have to be met by the devices regarding
- Various intputs and outputs
- Process signals
- Environmental conditions
- Communication and transmission technology
- as well as essential logical functions
|
|
Optimal Engine Power through Hydro-Mechanical Torque Control Eaton has added Hydro-mechanical Torque Control option for the versatile 420 series pump product line. Torque control limits the amount of input power that an open circuit pump will draw from the engine or prime mover. This control prevents engine stalling and helps in optimal utilization of engine power. This control allows a wide variety of application options to be met by a single pump control option.
Hydro-mechanical torque control provides a simple, low cost option for open circuit pumps. This new control complements the power-dense package offered by the 420 series product and is available in all four displacements (41cc, 49cc, 62cc & 80cc).
Applications
- Backhoe loader
- Skid steer loader
- Telehandler
- Mini-excavator
- Log-skidder
Features and Benefits
- Power dense design
- Compact design
- User defined torque setting
- Power/energy savings
- Prevents engine stalling
- Cost effective solution
|
|
|
The Promess Motorized Torque Control System is a plug and play, closed loop, CNC, measure and control system. The system is composed of an AC -Servomotor with integrated overload-protected torque transducer. This allows to link the NC-controled rotary-motion with monitoring of the torque / angel of rotation process. With the Unit you can trigger and monitor preciscly force and angle of force. The systemes can be linked with current bussystems and is availabel in different DIMENSIONS
|
|
DST4601/PX is the evolution of SICES renowned DST4601 AMF controller.
Aimed particularly to parallel application, thanks to its high degree of configuration, it can easily be used in quite all standard and special gen-set applications.
Born to manage the last generation of electronic engine, it supports CAN interface toward quite all most popular engines: J1939 protocol for VOLVO, SCANIA, DEUTZ, PERKINS, CAT, IVECO and MTU protocols for MTU engines.
A large graphic display, with a resolution of 240x128 pixels, allowed to implement a simple to use operator interface that is able, at the same time, to report an huge number of electrical and engine measures and information. Engine troubleshooting now can be made by textual interface (for example all MTU diagnostic codes are translated in plain English text).
|
|
|
|
|
|
Hydro-Control V- Water Control System for Concrete Mixing
Simple to use, accurate water control unit for use with the Hydro-Mix for manual or automated batch plants
The Hydro-Control V is a water control system from Hydronix. It is used in the concrete industry for controlling the mix cycle to automatically provide the correct addition of water in the shortest possible mixing time.
Using the reading from a Hydro-Mix or Hydro-Probe Orbiter sensor installed inside a mixer, the Hydro-Control V (HC05) accurately monitors the moisture levels of the material throughout the mix cycle, in both wet and dry mix stages. Using known recipes, the correct amount of water is then automatically calculated and added to the mix. This ensures that the required moisture target can be easily achieved, batch after batch.
Designed to be simple to operate and install, the Hydro-Control V can be used as a stand alone unit or installed into a control system, in both new and existing concrete plants. It has an easy to read graphical display which provides a wide range of information via a series of menus including mixing cycle status, recipe information, sensor signal trend and system diagnostics.
The unit incorporates a choice of different operating modes and is a multi-language system, making it the most versatile system on the market with different modes of control to suit all applications.
|
|
|
Bray Controls is proud to offer the Brayline series 50 Valve status Monitor, the future of valve position signaling. Bray's extensive field experience, research and development has produced the finest multipurpose switch/control monitors for industrial plant automation.
|
|
|
Vehicle master control unit is a type of a master unit, that when it is built in an electric vehicle makes through hardware and CANOpen network request for appropriate vehicle operation.
|
|
Model 1310 Vehicle System Controller
The latest generation of Curtis controllers, AC, allows for dynamic system configuration with embedded VCL. The new Curtis Vehicle Controller, Model 1310, extends this capability to other Curtis controllers. It is a single-point "Master" control of multiple vehicle functions which can be applied to electric vehicles, non-electric vehicles and stationary control systems. Model 1310 works in conjunction with Curtis CAN-based motor controllers and other CAN-open devices. It uses the industry standard 2-wire CAN-bus technology and integrates digital and analog signals with application- specific software.
|
|
Electronic controllers are mainly designed for battery-supplied electric drive systems based on DC commutator motors, BLPM-brushless permanent magnet motors and AC induction motors. They are designed for use in vehicle drives, pump drives and for some other applications.
The built-in electronic components allow for complete diagnostics of the system and are easy to program through hand console or a personal computer. The structure of all controllers enables fast and easy custom designing and compliance with almost all requirements of the application.
|
|
|
|
|
|
These solid state magnetic accelerators have been designed as speed input devices used for solid-state controls for electric vehicle traction motors. Applications include industrial fork lifts, utility vehicles, and airport ground support vehicles.
Input voltage : 18 to 80 volts DC
Output voltage (maximum) : 3.65 volts (nominal)
Output voltage (minimum) : 0.35 volts (nominal)
Start switch output voltage : Equal to user battery input voltage
Start switch output current : 3 amps continuous, 5 amps intermittent (10 seconds)
Note: This accelerator switch does not contain a 1A switch.
Features and Benefits:
- Start switch function is performed by a power MOSFET, in lieu of a mechanical device
- Typical actuator force is 5 lbs, and should not exceed 7 lbs
- Switch may be operated through a linkage mechanism or directly from the vehicle accelerator pedal
- Customer connection is made by means of a metric M10x1.5 male thread
- Underwriter's Laboratory Type EE construction, O-ring cover seal, blind mounting holes, and insulated wire hole grommet all combine to eliminate the need for periodic cleaning
- No mechanical adjustment required after installation
- Includes reverse battery protection and internal fusing for start switch over-current protection
- A hall effect sensor detects the input shaft displacement through the 0.75" shaft stroke
- Switch contains a push pull linear input shaft, with a typical 0.1" displacement for start switch closure
|
|
Series Motor Traction and
Pump Controllers
For motors up to 8.5 kW
The Powerpak™series Traction can be used in a single or twin motor systems. In a twin motor system it can be easily configured as master or slave. The Powerpak™Pump controllers comes with two variable and one configurable speed inputs. A range of contactor drive options are available to match the application
These controllers are also available on a variety of standard pre-wired panels complete with contactors, etc.
|
|
Users of conventional universal display units can have difficulty in making use of their device´s options menu. Special applications require many more functions that are often not available with conventional units.
KRAL BEM 300 to 500 electronic units enhances the KRAL Volumeter performance.
Your advantages:
- Two-channel, i.e. differential measurement.
- Temperature and pressure pulse compensation.
- Measurement conversion.
- 7 point linearization.
- Limit value for a relay output, i.e. regulation of a bypass valve.
- Threshold value for signal suppression.
- Clear and easily readable display.
- Accurate handling by the use of a clear menu structure.
- Multiple mounting options. (KRAL Volumeter, wall, pipe, control panel).
|
|
|
|
|
|
Interlock control system
A plug-in modular system for linking up to 10 doors, or up to 10 groups of doors to create an interlock system.
No complicated control system required as dependencies are set on site with DIP-switches at each control module. The system allows for easy expansion.
Quite often one of the requirements of clean-room technology or laboratories is, that certain doors may only be opened ifothers are closed. The DICTATOR interlock control system is the idealsolution to link units of up to 10 doors.
The dependencies between different doors are programmed directly in the
respective control modules on each door using a very easy adjustable matrix control system. This is done with DIP-switches representing the different doors. The dependences / linksnbetween the doors can also be changed on site at a later stage, not requiring any special programming
know-how. The interlock control terminal is provided with a potentialfree make-break contact. This permits e.g. to pass on the information on each door to a central control system.
The DICTATOR interlock control system is a modular system and therefore
extremely flexible and easy to adapt to different sizes of door units and
requirements.
|
|
|
It is an easy, sturdy and practical manual panel for generating sets control. It is easy for inspection. It is made in a metal box. It is provided with anti vibrating camping pads. It can be directly connected to the alternator.
|
|
Freelance 800F - The compact solution ABB's Freelance 800F control system combines easy engineering with an open, modern system architecture. Freelance 800F is proven in more than 14,000 applications - in all industries.
The compact control system allows the integration of all common fieldbuses, leaving the user to select any they wish - whether FOUNDATION Fieldbus, PROFIBUS, or HART.
The system was and will be continously improved and enhanced to meet our user's needs. Customers choosing Freelance 800F can rest assured that ABB will support them in the long term.
The new AC 700F controller has just been released. In addition, new Information Management functions are available via PGIM 800F, our new Information Mananagment option.
|
|
|
|
