|
|
The Tru-Trainer employs a unique and highly effective tracking action, which is non-damaging to the belt and reacts immediately if the belt begins to drift off center.
Because it does not rely on contact with the belt edge in order to guide the belt, belt edge damage, which occurs frequently with other tracking systems, is avoided. The center pivot is unique and simple, consisting of a stainless steel pin within a solid steel center shaft. Advantages include:
- Simple to Install
- Maintenance Free
- Operates In All Conditions
- Increases Conveyor Belt Life
- Reduces Spillage and Waste
- Minimum Working Parts
- Lower Motor Power Consumption
- Operates on Reversible Belts
- Rubber Covered for Better Traction
|
|
The Chevron secondary belt cleaner uses the speed and force of the belt rolling over our patented rubber disks. The unique rotary fingers are forced against the base of the chevrons to dislodge material from the belt.
- Sweeping Action - of each disk cleans in front of and behind each and every chevron.
- Easy Maintenance - no motors, air nozzles, or other problematic equipment to maintain.
- Works Great - in the pulp and paper, fertilizer, potash, and other bulk material industries where chevron style belts are heavily used.
- Solid or Notched - 8” (200mm) diameter abrasion resistant rubber disks are available depending on the height of the chevrons and the conveyor belt speed.
|
|
|
Flexco Chevron Belt Cleaner takes a new approach to cleaning chevron, cleated, and raised rib belts. Hundreds of rubber fingers create a rotary cleaning action that easily flicks carryback off the belt. And without the typical clogging and rapid wear problems associated with brush-type cleaners. Now there is a better solution for wet sand belts, wood chip belts and other raised top or grooved belts.
|
|
|
|
|
|
MARTIN® TRAC-MOUNT™ Idler
MARTIN® TRAC-MOUNT™ Idler uses sliding frames to fit into tight spaces between cradles, ensuring proper rolling support for the belt.
Simple Service
Individual rollers slide in and lock in place from outside the belt. No more laying idler sets on their side.
Proper Conveyor Belt Support In Tight Spaces
Slide-in frames need only 8 inches (203 mm) of width for 6-inch (152 mm) rollers.
Meets CEMA Standards
Available for any belt width or troughing angle, with any brand of rollers.
MARTIN® Transfer Points are custom-engineered by Martin Engineering to eliminate blockages, reduce impact, centralize loading and guarantee the material flow rate.
Martin Engineering makes bulk materials handling cleaner, safer and more productive, with engineered systems including conveyor belt cleaners, conveyor load zone/transfer point chutes, impact cradles and slider beds, skirtboard sealing systems, air-supported belt conveyors, air cannons, pneumatic (air) and electric industrial/bin/railcar/truck vibrators, belt training/alignment devices, dust suppression/collection/control systems, and specialized contract services including installation/maintenance and silo/bin/bunker cleaning.
|
|
|
Our brushing machine type BM 1138 has been constructed previously for heavy-duty conveyor belt cleaning in coal mines and foundries. Today we supply it for almost all kinds of industry where conveyor belts have to be cleaned.
|
|
|
|
|
|
MARTIN® Brush Belt Cleaners are specially suited for the removal of fines and residue from ribbed, flighted, grooved, or chevron belts. Versions are available to suit your conditions and your budget.
Motor-Driven Cleaning Action
One or two-horsepower motor (depending on belt width) turns brush against belt motion.
Match Cleaner To Requirements
Specify the cleaning system to suit your conditions and your budget.
MARTIN® Standard Brush Cleaner
MARTIN® Standard (Spiral) Brush Cleaner is value-priced answer to belt cleaning problems.
MARTIN® Strip Brush Cleaner
Uses 12 brush strips to form cleaner that sheds even moist material that would plug other brushes.
Brushes To Fit Need
MARTIN® Standard (Spiral) Brush Cleaner uses 0.38 inch (0.96 mm) polypropylene bristles wrapped in spiral around the hub. MARTIN® Strip Brush Cleaner forms brush from strips with 0.40 inch (1 mm) polypropylene bristles. Other materials and bristle diameters are available.
Martin Engineering is the world’s leading developer and manufacturer of engineered conveyor belt cleaning systems. In this position, Martin Engineering has developed fundamental principles of cleaner design that have set standards for belt cleaner engineering and performance.
The multiple-cleaner system originally adopted by Martin Engineering is now the standard for applications on belt conveyors carrying all types of bulk materials around the world. End users (and other cleaner manufacturers) have accepted it almost universally.
|
|
Tracker Rollers from HOSCH ensure conveyor belt alignment.
- Maintenance free
- No wearing parts
- Durable rubber surface
- Suitable for all environmental conditions
- Minimum space required, compact dimensions
- Ease of installation
- Minimum of installation
- Also suitable for reversing operation, ideal for retrofitting
|
|
Mink round brushes - Highly efficient tools with countless applications
Mink round brushes can be applied to solve problems in a wide range of areas, and our engineers have the ideas to exploit this potential. When it comes to flexibility, no industrial tool can match these brushes. We offer a huge selection of models: roller brushes (with stub shafts), round brushes (with hollow centre spindle, no shaft), the Mink HP-System (two half segments, without shaft) and the Mink Zick-Zack-System (modules, with or without shaft). Finally, there are Mink web spreader brush rolls for modern processing of plastic film, textiles and many other kinds of web.
Advantages:
• Suitable for goods of all kinds
• Versatile and economical
• Maximum cleaning power combined with optimum surface care
• Form and stiffness according to individual requirements
• Less need for cleaning agents thanks to the mechanical action of the bristles – economic and ecological benefits
|
|
Mink roller brushes (BW) - Individually configured roller brushes with shafts
Mink roller brushes differ from other Mink round brushes by virtue of their integrated shafts. Owing to the wide-ranging demands made on these brushes, especially in terms of shaft dimensions, there is no advantage in maintaining a stock range. Nevertheless, with our extensive experience in this area we are able to configure special brushes for you very quickly. On account of its extraordinary versatility the Mink Zick-Zack-System can frequently serve as the basis for a reliable solution.
Your advantage:
• Individual configurations for special purposes
|
|
Deburring and Roller Brushes
Use Deburring and Roller Brushes for a professional and perfect finish of cut edges. Diameter, filling material, measurements of the brush and the required bore are determined by the appointed machine and the work piece. We exclude any imbalance by evenly arranged filling material and the testing of every brush.
|
|
Deburring Brushes
Specially developed wheel brushes for deburring. These are suitable for all common deburring machines. Although they are heavier than other brushes because of their dense filling, we exclude any inbalance by evenly arranged filling material and the testing of every brush. Filled with high-quality wire, these brushes have a longer service life. All brushes are with double keyway. Please indicate the required bore.
Deburring End Brushes
These brushes are perfect for deburring tubes, profiles or even plane surfaces. Deburring end brushes are used in a set of 8, 16 or 24 single end brushes integrated in one deburring device. The metal bush fits all standard collets.
|
|
|
The modular principle underlying our one-way system of trapezoidal toothed roller brushes provides for fast, low cost changes of brushes. They can be installed and similarly removed by a simple hand operation. The teeth lock securely (and in a non-twist manner); as a result, a gap-free bristle surface is assured. Precise true running is guaranteed at all times. The DT system consists of brush segments which are mounted to the brush core with two locking collars. Due to the special modular principle on which they are based, worn individual segments on a roller brush can be replaced
|
|
| ... products without technical information |
| |
Features
Including positive drum brake: Max. service and parking braking torque 12000 Nm
Suitable for special distributor blocks designed to include valve cartridges
Overall dimensions and weight lower than direct drive units
|
|
The radial piston design ensures very high starting torque efficiencies, especially at high pressures where they are most required in mobile applications. Efficiency is typically > 94% at 400 bar.
The maximum torque requirement for wheel motor applications generally occurs with the vehicle al standstill or at low speeds, for example, during acceleration from stand-still or when overcoming an obstacle or slope.
High starting torque in the hydraulic motors therefore means better vehicle performance, less energy wastage and heat generation, especially with frequent stop-start work cycles.
|
|
|
|
|
|
Description
This wheel motor is the latest addition to the Char Lynn product line. The Delta motor provides torques up to 11,500 in-lbs. Eaton has packed this motor with many "best in class" features: the optimized geroler profile ensures smooth operation; the disc valve technology has the best performance and the bearing capacity is the highest in the industry for very demanding applications.
Features:
- Excellent reliability with time proven Char-Lynn components
- Proven disc valve technology with the highest efficiencies in its class
- Leak resistant motor with the front bearing protecting the shaft seal
- Torque up to 10,500 lb-in intermittant duty / Flow up to 30 GPM intermittant
- 12 displacements available from 6.9 to 46 CID
- Shaft sizes up to 1-5/8 inch
- 3-1/4 inch front pilot and 5 inch rear pilot
- STC ports available
Benefits:
- Perfect replacement for Parker® TF-TG and WhiteTM RE motors
- Lowest no load pressure drop which leads to longer life and lower temperature operation
- Highest overall efficiency: more available HP to the system than competitive motors
- The highest side load capacity with 4,500 lbs standard at 3" from the mount face
Applications:
- Scissor Lift
- Boom Lift
- Industrial Sweeper
- Mower
|
|
MG MOTORS
90° steering angle
Up to 450 bar [6 530 PSI]
From 830 to 2 800 cm³/tr [51 to 154 cu.in/rev]
The two-speed configuration allows the operator to adjust torque to ground conditions
Integral hydraulic displacement shift solenoid eliminates hydraulic control pressure line
Integral hydraulic swivel eliminates hose and fitting wear caused by hose bending
Simple bolt-on mounting simplifies vehicle assembly
Optional pivot bracket
|
|
| ... products without technical information |
| |
|
|
|
|
Nexen offers an advanced new technology that revolutionizes linear motion. The Roller Pinion System (RPS) provides zero backlash, very high positional accuracy, unlimited length, very high speeds, 99% efficiency, high rigidity, low noise, low maintenance, corrosion resistance, and long life. This opens up
new design possibilities and provides the capability to achieve much higher levels of performance in machine designs.
The RPS's unique design eliminates many of the limitations of current linear drive systems like:
Ball Screws: Limited by critical speed, maximum speed, cumulative error, vibration, thermal expansion, supplemental cooling, noise, low efficiency, maintenance, and life.
Traditional Rack and Pinion: Limited by low accuracy and speed, backlash, tooth fatigue, noise, high cost of dual and split pinion systems, high maintenance, and short life.
Belt Drives: Limited by low accuracy, backlash, low load capacity, short lengths, belt stretch, and low rigidity.
Linear Motors: Limited by low load capacity, high cost, strong magnetic fields, and liquid cooling.
|
|
|
|
|
|
The new benchmark for electrical preload on demanding machine tool applications!
KRPX is the new version of REDEX ANDANTEX rack & pinion high-tech planetary reducers, offering cost effective, easy to implement and high performing solutions for moving column or gantry machine types as well as many other applications.
The KRPX housing is made of high quality spheroidal graphite cast iron. Its structure has been optimised with FEM analysis methods to avoid deflection during acceleration. Fixation is made by oversized screws to ensure a real still connection with the machine frame allowing the KRPX housings to be considered as an integrated part of the machine main frame.
The output pinions are machined to the same diameter as the shafts, allowing the best possible balance between transmissible torque and rigidity at the rack. In addition, output bearing consists of two preloaded and substantially oversized angular contact roller bearings.
This exclusive design offers exceptional compound stiffness which allows to dramatically decrease the radial bending (up to 60% of the overall distortion) and to increase the natural frequencies of the global Racks & Pinions drive systems.
Designed as an association of two high-tech planetary reducers, KRPX allows perfect mounting on both sides of the machine frame and enables true zero backlash when coupled with an electrical preload system.
Available in 3 standard universal sizes (2, 3 and 4) KRPX is very compact, a definitive advantage for helping implementation with respective pinion height not higher than 104, 127 and 148 mm.
With this new and innovative concept, the machine-tools designers can easily expect to exceed market standards with maximum feed capacity up to 105 000 N and stiffness on the rack up to 333 000 N/mm.
|
|
Dedicated to racks & pinions drive applications, the KRP+ design is based either on the use of one single unit or on the association of two top quality planetary reducers, mounted in parallel on the machine main frame.
When used as a SingleDRIVE, the KRP+ gives the benefit of an ultra high stiffness feed gearbox, dedicated to high performances rack & pinions drive systems.
When choosing the mechanical preload solution, the KRP+ become a DualDRIVE unit, which achieve the true backlash free feature by torsionally winding one pinion against the other through the rack.
Immediate benefits are to need only one motor, and to dramatically simplify the motor control.
When choosing the Electrical preload solution, the KRP+ is used as a TwinDRIVE unit, where the backlash is cancelled by the opposite torque balance between the two pinions, according with the two motors and drives remote control.
|
|
Dedicated to racks & pinions drive applications, the DRP+ design is based on the association of two top quality planetary reducers, mounted in parallel on an extra high stiffness universal frame.
When choosing the mechanical preload solution, the DRP+ become a DualDRIVE unit, which achieve the true backlash free feature by torsionally winding one pinion against the other through the rack.
Immediate benefits are to need only one motor, and to dramatically simplify the motor control.
When choosing the Electrical preload solution, the DRP+ is used as a TwinDRIVE unit, where the backlash is cancelled by the opposite torque balance between the two pinions, according with the two motors and drives remote control.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
