|
|
The Tru-Trainer employs a unique and highly effective tracking action, which is non-damaging to the belt and reacts immediately if the belt begins to drift off center.
Because it does not rely on contact with the belt edge in order to guide the belt, belt edge damage, which occurs frequently with other tracking systems, is avoided. The center pivot is unique and simple, consisting of a stainless steel pin within a solid steel center shaft. Advantages include:
- Simple to Install
- Maintenance Free
- Operates In All Conditions
- Increases Conveyor Belt Life
- Reduces Spillage and Waste
- Minimum Working Parts
- Lower Motor Power Consumption
- Operates on Reversible Belts
- Rubber Covered for Better Traction
|
|
|
|
|
|
MARTIN® TRAC-MOUNT™ Idler
MARTIN® TRAC-MOUNT™ Idler uses sliding frames to fit into tight spaces between cradles, ensuring proper rolling support for the belt.
Simple Service
Individual rollers slide in and lock in place from outside the belt. No more laying idler sets on their side.
Proper Conveyor Belt Support In Tight Spaces
Slide-in frames need only 8 inches (203 mm) of width for 6-inch (152 mm) rollers.
Meets CEMA Standards
Available for any belt width or troughing angle, with any brand of rollers.
MARTIN® Transfer Points are custom-engineered by Martin Engineering to eliminate blockages, reduce impact, centralize loading and guarantee the material flow rate.
Martin Engineering makes bulk materials handling cleaner, safer and more productive, with engineered systems including conveyor belt cleaners, conveyor load zone/transfer point chutes, impact cradles and slider beds, skirtboard sealing systems, air-supported belt conveyors, air cannons, pneumatic (air) and electric industrial/bin/railcar/truck vibrators, belt training/alignment devices, dust suppression/collection/control systems, and specialized contract services including installation/maintenance and silo/bin/bunker cleaning.
|
|
Tracker Rollers from HOSCH ensure conveyor belt alignment.
- Maintenance free
- No wearing parts
- Durable rubber surface
- Suitable for all environmental conditions
- Minimum space required, compact dimensions
- Ease of installation
- Minimum of installation
- Also suitable for reversing operation, ideal for retrofitting
|
|
The Chevron secondary belt cleaner uses the speed and force of the belt rolling over our patented rubber disks. The unique rotary fingers are forced against the base of the chevrons to dislodge material from the belt.
- Sweeping Action - of each disk cleans in front of and behind each and every chevron.
- Easy Maintenance - no motors, air nozzles, or other problematic equipment to maintain.
- Works Great - in the pulp and paper, fertilizer, potash, and other bulk material industries where chevron style belts are heavily used.
- Solid or Notched - 8” (200mm) diameter abrasion resistant rubber disks are available depending on the height of the chevrons and the conveyor belt speed.
|
|
|
Flexco Chevron Belt Cleaner takes a new approach to cleaning chevron, cleated, and raised rib belts. Hundreds of rubber fingers create a rotary cleaning action that easily flicks carryback off the belt. And without the typical clogging and rapid wear problems associated with brush-type cleaners. Now there is a better solution for wet sand belts, wood chip belts and other raised top or grooved belts.
|
|
|
Our brushing machine type BM 1138 has been constructed previously for heavy-duty conveyor belt cleaning in coal mines and foundries. Today we supply it for almost all kinds of industry where conveyor belts have to be cleaned.
|
|
|
|
|
|
MARTIN® Brush Belt Cleaners are specially suited for the removal of fines and residue from ribbed, flighted, grooved, or chevron belts. Versions are available to suit your conditions and your budget.
Motor-Driven Cleaning Action
One or two-horsepower motor (depending on belt width) turns brush against belt motion.
Match Cleaner To Requirements
Specify the cleaning system to suit your conditions and your budget.
MARTIN® Standard Brush Cleaner
MARTIN® Standard (Spiral) Brush Cleaner is value-priced answer to belt cleaning problems.
MARTIN® Strip Brush Cleaner
Uses 12 brush strips to form cleaner that sheds even moist material that would plug other brushes.
Brushes To Fit Need
MARTIN® Standard (Spiral) Brush Cleaner uses 0.38 inch (0.96 mm) polypropylene bristles wrapped in spiral around the hub. MARTIN® Strip Brush Cleaner forms brush from strips with 0.40 inch (1 mm) polypropylene bristles. Other materials and bristle diameters are available.
Martin Engineering is the world’s leading developer and manufacturer of engineered conveyor belt cleaning systems. In this position, Martin Engineering has developed fundamental principles of cleaner design that have set standards for belt cleaner engineering and performance.
The multiple-cleaner system originally adopted by Martin Engineering is now the standard for applications on belt conveyors carrying all types of bulk materials around the world. End users (and other cleaner manufacturers) have accepted it almost universally.
|
|
Long experience in producing Rolls for Hot Rolling
More then 200,000 cemented carbide rolls have been produced by Sandvik Hard Materials since 1965. The cast-in-carbide (CIC) concept takes this material a step further, as demonstrated in hot rolling mills all over the world.
Sandvik’s CIC technology offers new opportunities for rolling mill managers to improve product quality, reduce down-time and increase productivity.
Containing an optimised combination of cemented carbide and ductile iron, Sandvik CIC rolls combine excellent passform wear resistance with high strengt and toughness in the roll body.
The composite design of CIC rolls means that the carbide performs the rolling, while torque transmission is handled by the ductile cast iron.
|
|
|
Staightening rolls, guiding rolls and deflection rolls made of different materials and with coatings. High performance rolls for process matérial speeds up to 70 m/s and for straightening forces up to 300 kN.
|
|
|
Guiding units with or without centric roll adjustment and single roll guides.
|
|
| ... products without technical information |
| |
• Telescope action jacks; for corner routes
• Suitable for laying lines of cable
• For pit cable inlets or outlets.
• For laying cables over ducts corresponding to corner passages.
• For the horizontal positioning.
|
|
|
|
|
|
JETnet® is based on a flexible network architecture with OFC-cables and is applied for long distances as well as for local applications. This solution offers especially for the "last mile" largest possible flexibility for extending transfer capacities with customers and for optimised investments.
That system is developed as a unit construction system using many known components and is completed with construction elements and technologies adjusted to special application purposes. It is based on an individually applicable tubing system embedded in standard HDPE protection tubes. With the tubing system OFC cables adjusted to customer requirements can be blown in without splicing. Extension on customer request can be realised quickly, without engineering operations and at low cost.
In many countries worl-wide the JETnet® priciple has proven its functionality and cost advantages. Projects have been realised in Germany, too. Its module construction principle with simple technologies realizes quick reaction on new projects and changed customer requirements. A complete product range of construction elements of cables and tools is available, being excellently qualified for rough field application. As it is compatible with already existing protection tube systems it extends the universal application possibilities and offers the solution necessary for a future orientated connection network.
Besides offering and supply of JETnet® components Draka Comteq offers additional support for planning of microcable routes of FTTH-networks.
|
|
Wichard offers a comprehensive range of roller blocks used in various industrial applications: transport, event etc...
> Sheave diameters: 30, 40, 50, 65 and 80 mm
> For rope size from 6 to 12 mm
> Delrin rollers
> Aluminium sheave (with hard anodisation)
> Fastening system: forged shackle (grade 316L stainless steel)
> Sheave protected by cheeks
A "High Resistance" model is avaible:
> Fastening system: forged shackle (AISI 630)
> Sheave diameters: 65, 80, 100 and 125 mm
> For rope size from 8 to 20 mm
> Torlon rollers
> Aluminium sheave (with hard anodisation + Teflon)
|
|
Magnetic roll
Materials: HF 28/15, soft iron, brass
Temperature: maximum 200°C
Execution: Magnet raw, zinc coated iron magnetised
|
|
Several types of magnetic rollers for can conveying systems are produced by Walker Magnetics
rollers for single transport
As part of our mass conveying program, we produce magnetic wide size rollers in any width. Rollers of 2500mm long are in regular production.
magnetic plates
All our rollers are built to complement our magnetic plates,
thus ensuring a good flow.
This range covers most of the requirements for modern can handling. For special applications, we produce tailor-made rollers, plates and curves according to customer's requirements.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
Omniwheels Series 2500
Features
- Conveyance in any direction possible
- Simply designed crossings and switches
- Version driven in one direction possible with hexagonal spindle
- Wheels can be coupled to one another
- Easy to assemble
- Can be used in a dusty environment
- Can be used in a moist environment (stainless steel journal)
- Bottom of the items must be flat and sturdy
- Corrosion resistant
- Load capacity: 500 N per wheel
Standard part numbers
2570 - 48 mm dia.
2580 - 80 mm dia.
Dimensions
Outside diameter 48 or 80 mm
Hub bore dia. 8.2, 12.2, 16.0 mm 11.2 hex or 19 hex
|
|
|
|
|
|
Mink web spreader rolls (BSW) – for wrinkle prevention
Systems for guiding the movement of plastic films and webs have a strong tendency to make wrinkles, resulting in defects. Mink web spreader rolls™ offer a dependable solution to this problem – at unbeatable prices. The bristles, which are inclined at a precisely determined angle, push out on the film from the middle, ensuring that it stays smooth. Marks or imprints that could impair quality are prevented. Mink web spreader rolls can easily be installed at every critical point in a system. Because they are so inexpensive, it even pays to use them as a replacement for pinch rolls. The freely turning roller, mounted on ball bearings, rotate much more easily than other types of spreader rolls. Mink web spreader rolls can be delivered ready to install within a few days, according to your dimensions and specifications.
Advantages:
• Plastic films and webs are kept perfectly smooth during processing
• The spreading effect begins right where the spreader roll and web make contact
• This sophisticated system replaces inadequate alternatives
|
|
|
|
see the results for the following category : 
