- Electricity - Electronics >
- Electronic Component >
- Current isolator
Current isolators
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
... collector Isolator Signal Input Voltage / Encoder Signal Output Voltage - 5-30 VDC (TTL, RS422, line driver) Isolator Frequency Response - Max 1Mhz Isolator Supply Voltage ...
... Argodiode battery isolators, Argofet isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. ...
Victron Energy
... integrity of your datas. Description: - AC current to DC isolator / converter Input: - Current (0..5, 0..10 A) Output: - Current ...
SENECA | Automation Interfaces
... can power also all 2-wire sensors and it can be used to solve also power conflicts into the same mA loop. A 3-way galvanic isolation among Power supply // input // output circuits assures ...
SENECA | Automation Interfaces
... circuits assures the integrity of your datas. Description: - DC current isolator (self-powered) single channel Input: - Current 4..20 mA Output: - Current ...
SENECA | Automation Interfaces
... used for galvanic isolation and amplification of DC signals (mA). Description Input and output are galvanically isolated with a high degree of isolation. The integrated high-efficiency electronic power ...
Pasternack RF isolators are used for protection of radio-frequency components from signal reflection and excessive current. They are passive 2-port devices that use microwaves. These coaxial RF isolators ...
... enables compliance with the ATEX directive. • 1-channel isolated barrier • 24 V DC supply (loop powered) • Current input/output 0 mA ... 40 mA • I/P or transmitter power ...
... voltage and current are dependent on the load and the input voltage At full load, 10 V at 45 mA is available for the hazardous area application. • 1-channel isolated barrier • 24 V DC supply ...
... Auto Zero Calibrating -. 4 ~ 20mA current output -. Input Signal Types can be configurated by external USB adaptor -. Loop Power Current Limit < 30mA -. Input Over current ...
The SP02, manufactured by Aplisens, is a current signal isolator without auxiliary power that features a single or dual-circuit in a 12.5 mm wide enclosure. It features an accuracy rate ...
• galvanic separation of current loop circuits • passive separator, requires no power • linear conversion of current signal 0÷22mA into current signal 0÷22mA • high ...
• galvanic separation of current loop circuits • passive separator, requires no power • linear conversion of current signal 0÷22mA into current signal 0÷22mA • high ...
... Product details The BA201 communications isolator is a dedicated interface for connecting intrinsically safe BEKA Serial Text [Data] Displays to a safe area computer system. The communications isolator ...
... signal isolator TRI is a compact 2-wire current-to-current transmitter providing optical isolation between the input and output current loops. The isolation level is ...
Isolation amplifier with current or voltage input 4 selectable input ranges and 4 selectable output ranges 12-30 V supply, isolated from internal electronics Built-in supply for external transmitter Galvanically isolation ...
Each DSCL20 loop powered isolator provides a single channel of analog signal protection by electrically isolating its input from output for any DC process signal in the range of 0-20mA (or 4-20mA). The ...
Dataforth Corporation
Each DSCL21 loop powered isolator provides a single channel of analog signal protection by electrically isolating its input from output for any DC process signal in the range of 0-20mA (or 4-20mA). The ...
Dataforth Corporation
Each DSCL23 loop powered isolator provides 1, 2 or 3 channels of analog signal protection by electrically isolating its input from output for any DC process signal in the range of 4-20mA. The DSCL23 feeds ...
Dataforth Corporation
1202 Eliminate multi-battery drain when two or more battery banks are in a charging system. 12023A Eliminate multi-battery drain when two or more battery banks are in a charging system. 1203 Eliminate multi-battery drain when two or ...
(-50 to 50) V or (-50 to 50) mA Input Current, Voltage Or Bipolar Voltage Output Accepts Internal and External Powered Current Loops On Input and Output Powered ( 10 to 32) V AC / ...
... Input-Output Galvanic Isolator provides signal transmission and conversion between DC current or DC voltage signal source and signal processing units. The instruments ...
EM-M14 is an easy way to isolate current loop signals obtaining a good accuracy. No additional supply voltage is required. Voltage drop is minimal although the input voltage range is very wide. EM-M14 isolator ...
Electromen
This device is designed to isolate 4/20mA signals between the safe and the hazardous areas. Input:Current (4/20mA) Output: Current (4/20mA) Supply: No power supply required Model: 1, ...
GEORGIN S.A.
... batteries require independent charging with reliable battery isolators or battery combiners. Mastervolt offers several intelligent solutions: •Battery isolators that divide your charge current ...
Mastervolt
... or Panel Mounted compact Current Isolator Isolated Input, Output and Power Supply (3 Port Isolation) 4-20 mA Input 4-20 mA isolated output Output zero and span set by use of potentiometer Additional ...
The galvanically isolated safety barriers TSU400 are valid alternative to passive barriers because they don’t need a high integrity I.S. ground, being the isolation between the safe area and the hazardous area guaranteed by a transformer. ...
SISO3 is a signal isolator that electrically isolates the intrinsically safe circuit from non-intrinsically safe circuit such as a data acquisition system, e.g. AMSY-5 or AMSY-6. A SISO3 is required if an ISAS3 is installed ...
... isolation eliminates ground loops, reduces noises and blocks transient signals. What is the Galvanic 0-10V or 0-5V Isolator? The LSP-IV2 isolator is designed to make galvanic isolation between the ...
Levtech Service Production SRL
... logger, display, recorder, etc.). DIN Rail Mounted Transmitter Isolator AI-7021D5 -COMPACT SIZE -Accuracy : 0.3%FS -Input: Pt100, Cu50, K, S, R, E, J, T, B, N, WRe5-WRe26, linear current, -Output ...
The ACR-160m which is manufactured by Samlex, is an automatic charge isolator which fuses battery banks for charging, and disconnects them when they are done charging. The unit prioritizes charging of the starter battery, ...
3-way CURRENT ISOLATOR, 1.5 kV galvanic isolation, suitable for isolating a 0-4…20mA signal, ready to be mounted on DIN rail. Analogue output in active and passive current. INPUT: ...
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining