|
|
OMICRON's CT Analyzer is a unique lightweight electronic multifunctional instrument designed to meet the highest standards for performing excitation, ratio, polarity and winding resistance tests on current transformers (CTs) as well as burden-impedance measurement.
Benefits
* Extremly small and lightweight (< 8kg/17 lb), beneficial for on-site testing
* Reduced commissioning time due to fully automatic testing
* Allows testing and result assessment according to IEC 60044-1, IEC 60044-6 or IEEE C57.13 (ANSI standard)
* Accuracy level (0.02 %/1 min.) enables field calibration and verification of class 0.1 CTs for metering
* Testing of specialized CTs such as TPS, TPX, TPY and TPZ
* Automatic analysis of CTs with unknown data ("name plate guesser" function)
* Recalculation of test results after tests with different burden and different primary current (no further on-site measurements)
* High level of safety - all tests utilize low voltages (120V)
European Patent EP 1 398 644 A1
* Almost unlimited in: Ratio (50 000 : 1), Primary current (999 000A max.),
Knee point voltage (15kV max.)
* Automatic demagnetization of the CT after the test
* Data storage on a removable Compact Flash (CF) card, which can be read by any standard memory card reader
* Remote interface to integrate CT-Analyzer into an automatic production process
* Easy importing and editing into MS OfficeTM standard software
|
|
296: 4,000 count manual ranging digital clamp-on meter with analog bar graph, True RMS, frequency, % harmonic distortion, data hold, Min/Max/Peak, and sleep mode/auto off.
293: 4,000 count manual ranging digital clamp-on meter with analog bar graph, True RMS, frequency, trim mode, data hold, peak hold, and sleep mode/auto off.
291: 4,000 count manual ranging digital clamp-on meter with data hold, and peak hold
275: 11,000 count autoranging digital clamp-on meter with True RMS, frequency, capacitance, temperature, non-contact voltage detection, data hold, relative mode, Min/Max/Peak, peak hold, sleep mode/auto off, 0.5% Basic DC accuracy
270: 4,000 count autoranging digital clamp-on meter with analog bar graph, frequency, capacitance, temperature, non-contact voltage detection, data hold, relative mode, Min/ Max/Peak, peak hold, sleep mode/auto off
265: 4,000 count autoranging digital clamp-on meter with frequency, capacitance, data hold, and sleep mode/auto off
250: 4,000 count manual ranging digital clamp-on meter with data hold, and peak hold
|
|
| ... products without technical information |
| |
The leak detector ET97W represents the best solution on the market in terms of precision, flexibility and execution speed of seal tests with measure in flow rate.
This instrument allows to measure in a direct way the air flow generated by the leak-off rate.
ET97W is composed of a pneumatic circuit optimized in order to reduce the filling times, of a mass flow sensor, of a pressure
sensor and of an electronic pressure regulator, that guarantees stable and safe test pressures without the operator assistance.
The instrument detects the leaks through continuous seal measure of the pressurized piece, this method allows to reduce
drastically the time of the test phase.
ET97W is specially used in seal tests where the volume of the piece is unknown and variable (oil motors, elastics bags or
bottles), when the leak entity is so elevated that a Äp system does not succeed to maintain constant the test pressure (cartridge valves, oil distributors, between filaments) and finally when is requested a continuous leak measurement in order to allow the operator to look for and repair the same one.
|
|
DELTA F is an electro-pneumatic equipment able to measure the air flow rate and the generated pressure through the piece in test.
The output pressure control assure the test is always performed on the same condition.
The equipment can be used manually or managed by a PLC or Personal Computer.
So it can be used also with automatic system in every industrial situation.
* 16 programmable test parameters tables: each table includes all the parameters defining a test cycle so it is easy to make predefined test setting for different products
* Selectable pressure measurement units
* Selectable flow measurement units
* Selectable languages for display messages
* Print out of customized test report (with external RS-232 printer)
* RS422 serial line MODBUS protocol for PC supervisory system
* Opto-isolated interface with PLC
* An aided procedure making it possible to calibrate the pressure sensor
|
|
|
Designed to slip easily into the bed of a pick-up truck, Seraphin® Slip-On Volumetric Calibration Unit can speed the job of calibrating multiple fuel dispensing units, while at the same time, enhancing safety. The unit consists of three 5 gallon or 20 liter NIST compliant bottom drain provers individually plumbed to 80 gallon stainless steel transfer tanks. The 80 gallon configuration allows for up to 48 calibration tests before returning to the fuel station's storage tank for dumping.
|
|
|
The Seraphin® waterdraw system is comprised of bottom drain stainless steel provers and at least one top drain measure mounted on top of a stainless steel water reservoir. The provers drain via gravity into the reservoir. A 5 HP pump takes suction from the bottom of the reservoir tank and discharges to an inlet fitting of the customer's dynamic pipe prover, via a portable quick-connect hose. The discharge side of the customer's pipe prover connects to a stainless steel manifold which is plumbed to the top neck of each individual prover. Various combinations of Seraphin® provers can be used to calibrate different size pipe provers. A solenoid operated valve at the inlet of the waterdraw manifold is connected, through relays in the control panel, to the detector switches of the pipe prover. The system will shut down when the sphere reaches the second detector switch. The volume between detector switches will be captured in the Seraphin® measures.
|
|
|
|
see the results for the following category
