|
|
Gear Shaving Cutters. Gleason manufactures
and resharpens precision shaving cutters to
support Gleason Hurth shaving machines and
any other gear shaving machines. The
Gleason shaving cutter design is optimized
for maximum tool life.
|
|
|
Dathan disc type cutters can be designed and produced for cutting any type of gear, internal or external, spur or helical. They can also be designed to cut splines, serrations, sprockets or other involute forms. The cutters are full form generated using the Dathan 'pass thro' method. These cutters may be manufactured with bore diameters from 10mm to 120mm or ½" up to 4", cutter diameters (pitch circle diameter) from .75"(19mm) to 10"(250mm) and can be manufactured to any world standard or to any specified requirement.
|
|
SHANK TYPE CUTTERS
These are primarily designed for cutting internal gears, splines and serrations, both spur and helical. May also be designed for externals if required. These cutters are full form generated however small the pitch circle diameter (PCD) although strength of the cutter produced is the limiting factor. The strength and rigidity of shank type cutters is greatly improved by the Dathan ribbing method and is especially advised for those of small PCD.
HUB TYPE CUTTERS
Dathan hub type cutters are designed for cutting internal components where maximum rigidity is required. Hub type cutters are recommended for cutting long face widths or for coarse pitches.
In general terms, any tooth form, face width or number of teeth that is available on a shank cutter, can be manufactured with a hub type fitting. Note: these cutters screw directly onto the spindle of the machine therefore rely on the spindle being in a good true state.
|
|
STRAIGHT BEVEL GENERATING TOOLS
These are produced for Gleason machines, 24", 18", 12", 11" ,6" and 3" both roughing and finishing and also for Heidenreich and Harbeck machines, 15KH, 25KH, 26KH, 60KH and 75KH. These are manufactured as standard in M2 HSS, though tools in 5% colbalt steel can be supplied to order.
|
|
Convert now to cutting reliability at higher speed
At Sandvik Hard Materials we regard the cutting function as a single system that forms an integral part of the converting line. Using Sandvik CRC (Carbide Rotary Cutters), your converting line will face no restrictions in the cutting function (up to 1800 pieces/min).
Sandvik CRC are designed on the basis of a powder metallurgy process. The resulting material is both harder and stiffer with superior thermal conductivity compared with steel which makes cemented carbide ideal for rotary cutters. It is possible to resharpen the cutters several times during their lifetime.
|
|
Gear Milling Cutters
- Gear Roughing Cutters
- Circular-type Gear Profile Cutters with Form Indexable Inserts
- Roughing Cutters for Rotors with Indexable Inserts
- Rotor Profile Cutters with Inserted Blades
|
|
| ... products without technical information |
| |
|
Tough, reliable and easy to use. Vemeer is the inventor and the world's leading seller of stump-cutting equipment. The reason is simple - Vermeer offers machines that are tough, reliable and easy to operate. With features like the exclusive AutoSweep system, beltless cutter-wheel drive systems, Pro Series teeth and state-of-the-art remote controls, the Vermeer name has become synonymous with innovation. Proven on virtually every type of hardwood stump, the Vermeer line of labor-saving stump cutters lets you do it all.
|
|
Features:
- Cutterwheel is equiped with FERMEX teeth
- Very solid construction
Advantages:
- Easy to operate
- Easy to transport
- Long lifetime
Benefits:
- 30 % more productivity
Additionally to the well known piling machines Vermeer MT also supplies auxiliary equipment. Examples are the Easy Cutter (pipe cutting system), drop weights (750 - 4000 kg class,with or without connections),
tubes (114 up to 508 mm) and swaging units.
Swaging units expand tubes in such a way that the original
tube size fits into the swaged end giving the connection a
high quality after welding it.
It also saves labour against other coupling methods like connection rings.
The TU-series Vermeer MT swaging units can be supplied as Standard
and as a Wide Range model.
Both systems are suitable for swaging pipes that are regularly used in the foundation industries.
|
|
Features:
- Cutterwheel is hydraulicly driven
- Cutterwheel is equiped with FERMEX teeth
- Optimal balance between motor, pump, hydraulic motor
and cutterwheel
Advantages:
- Easy to use
- Solid construction
- Highest periphirical speed
Benefits:
- up to 70% more productivity
- 20% less cost
FERMEX, manufactured by Vermeer MT, has 6 standard models of stump cutters.
It is possible to chose from hydraulicaly or mechanicaly driven machines, and machines which use the P.T.O. of a tractor or it's own power unit.
FERMEX stump cutters are designed and built for the professional user.
The machines are robust, have few wear parts and are making a high production.
The applied teeth/ pockets system results in quick mounting because
no gauges are required.
The locking of the teeth combined with the pockets lead to safe usage.
The Vermeer MT teeth are provided with tungsten carabide plates that extend the lifetime.
|
|
| ... products without technical information |
| |
|
Rugged, reliable and powerful, Vemeer concrete cutters can be found working repair and replacement projects on streets and roadways worldwide. Vermeer concrete cutters are perfect for patch and joint placement on interstates, streets and highways. Other applications include cutting highway and bridge relief joints, creating lateral ditches for highway drainage, work on street and airport lighting projects, installation of airport guidance systems and demolition work for widening shoulders and airport pads.
|
|
|
|
|
|
RZ 111 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 110
Blade diameter mm 300 (350)
Engine HONDA Type GX 160
Max. engine power @ RPM kW 4,0/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 3600
Water tank capacity l 15
Water supply aqua spojka
Weight kg 55
RZ 120 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 120
Blade diameter mm 350
Engine HONDA Type GX 270
Max. engine power @ RPM kW 6,6/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 3400
Water tank capacity l 20
Water supply aqua spojka
Weight kg 95
RZ 121 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 120
Blade diameter mm 350
Engine HONDA Type GX 270
Max. engine power @ RPM kW 6,6/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 3400
Water tank capacity l 20
Water supply aqua spojka
Weight kg 72
RZ 170 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 170
Blade diameter mm 450
Engine HONDA Type GX 390
Max. engine power @ RPM kW 9,6/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 2800
Water tank capacity l 20
Water supply aqua spojka
Weight kg 106
RZ 171 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 170
Blade diameter mm 450
Engine HONDA Type GX 390
Max. engine power @ RPM kW 9,6/3600
Travel ruční
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 2800
Water tank capacity l 20
Water supply aqua spojka
Weight kg 78
|
|
|
Floor Saw Blades from TYROLIT and Floor Sawing Machines from TYROLIT Hydrostress - an unbeatable combination.
|
|
|
|
|
|
SHARK CUTTER SUCTION DREDGE
Dredging Supply Company's Shark Class Cutter Suction Dredge features a conventional dredge-operating configuration with modular design for ease of transportation. With standard discharge sizes ranging from 10-inch through 24-inch, our Shark dredges are most commonly used by sand & gravel producers and contractors. The tough yet portable design offers many rewards for the end user. With the proven reliability of the Shark Class cutter suction dredge, the end user can expect a very long life expectancy for this type of equipment. The Shark dredge will provide a high percentage of uptime and availability, which makes it one of the best selling models in the world!
DSC's Shark Class Dredge features standardized systems throughout all of the various sizes and configurations. The operating systems are all PLC based and offer the operator an ergonomic and user-friendly control panel. With the simple touch of a few switches, you are off and dredging. The Shark dredge also features power up/down spud systems with API rated winch drums for proper cable storage.
|
|
TF: automatic cutters for custom-sized spools of PS film, thickness range: min 0.15 max.0.3 mm.
Final sheet size: min 400x 400, max 1000x1500 mm.
A V-shaped corner-cutting system is available on request.
The cutter is electronically controlled from a panel with auto, single, manual and double cycles, the latter indispensable to obtain lenghts of more than 800 mm
|
|
| ... products without technical information |
| |
|
Double E offers core cutters in manual, semi-automatic and fully automatic models. Each model cuts cores efficiently and quietly without creating sawdust. The machines accept cores with diameters ranging from 38 mm (1.5") to 200 mm (8"), and wall thickness up to 20 mm (.75"). A simple and quick modification allows the machine to switch between various core ID’s.
|
|
| ... products without technical information |
| |
Better cutting - manual cutting systems
the ergonomically formed cutting carriage with cutter cassette cuts with absolute safety in both directions.
The cutter cassette can be replaced in one easy operation.
cassette with circular knife for paper, corrugated board etc.
cassette with blade for film
for use with roll material, such as paper, corrugated board or foil, we offer you the time-tested cutting systems with dispenser
freestanding or directly at the packing location
with changeable cutting cassette
standard cutting widths up to 160 cm, vertical cutting stand up to 200 cm
|
|
|
|
|
|
900 Series Belt Cutter
Safely and Accurately cuts belts up to 1-1/2" (38 mm) thick and up to 84" (2130 mm) wide.
Advanced features allow the 900 Series* Belt Cutter to achieve accurate cuts, every time:
- Robust blade design is guided at the top to ensure perpendicular cuts
- Single-sided clamp feature allows belt to fall free from cutting edge for reduced operator effort
- Integrated belt grip surface with gentle serrations for added clamping strength
- Cambered bottom beam provides uniform clamping force across the entire belt width
840 Series Belt Cutter
Make straighter cuts with the lightweight, easy-to-use 840 Series aluminum belt cutter.
Designed to enhance operator safety on belts up to 84" (2.1m) wide, the 840 Cutter grips belts securely. The chain-driven, double-edged safety blade is shielded from operator contact, and cuts rubber or PVC belts up to 1" (25mm) thick. The blade can be driven from either end of the cutter and cuts in both directions.
Sturdy aluminum construction means lighter weight for easy maneuverability and corrosion resistance in wet underground mining environments.
Clipper® 845LD Belt Cutter
A sturdy, safe, simple and portable tool specially designed for cutting wide belts. The enclosed blade is handle-driven from either end, cutting belts up to 1/2" (12mm) thick. Available in widths of 36", 48", 60", and 72" (900, 1200, 1500, and 1800mm).
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|