|
|
EFP MultiPosition Cylinder
Provides three position output on extension using the same EF bore footprint to save space.
Easily interchangeable to other compact extruded cylinders of the same bore size.
Available in 10 bore sizes from 12mm to 100mm.
Versatile to easily connect and operate with application's pneumatic logic.
PTFE impregnated, hard anodized aluminum body for superior wear resistance.
|
|
|
|
|
|
Flat-II
Flat-II nonrotating, double-acting cylinder provides the answer to applications where rotation cannot be tolerated and space is at a minimum.
Nonrotation is achieved with dual piston rods and a rod end block that insures the rods work in tandem. Eliminates the need for external alignment devices, such as guides, rods and alignment posts or pins.
Body - 304 Stainless Steel
Heads - Anodized Aluminum Alloy
Piston Rod - Ground and Polished 303 Stainless Steel
Piston Seals - Buna N (High Temperature Seals Optional)
Rod Bushing - Oil Impregnated Bronze
Rod Seals - Buna N O-ring (High temperature seals optional)
Rod End Block - Anodized Aluminum Alloy
Pressure Rating - 200 PSI Maximum (Air only)
Temperature Rating - From -20°F to +150°F (-25°C to +65°C) Buna N seals with a temperature range of -20°F to +150°F (-25°C to +65°C) are standard in all Bimba air cylinders. Fluoroelastomer seals rated for higher temperature applications are available. If cylinders are operated below -0°F (18°C) for extended time periods, special modifications may be required.
Special seal materials are available upon request!
|
|
Non-Rotating Air Cylinders
* Bimba’s new Non-Rotating Original Line stainless steel body air cylinder design consists of a unique square piston rod with rounded corners. The square rod prevents rotation better than other rod configurations, and the rounded corners provide longer seal life than conventional hexagon rods. The unusual geometry of the square rod also provides superior rotation control.
* All bore sizes have a rotational control of less than or equal to ±3 degrees. Bore sizes for the non-rotating cylinders are 9/16", 3/4", 1-1/16", 1-1/2", 2", and 2-1/2".
* The special high strength aluminum alloy rod guide provides high load carrying capability and abrasion resistance. The urethane-based rod seal provides excellent seal life and leak-free service.
* The Non-Rotating Original Line cylinder is dimensionally interchangeable with the standard Original Line stainless steel cylinder.
* Available in Double Acting and Reverse Acting models.
|
|
Magnetic piston is included as standard.
Rugged body is machined from aluminum extrusion and mounts rigidly to equipment in a minimum of space.
A variety of styles are offered to meet different application requirements.
The direction of rollers are adjustable for use in different applications.
Shock absorbers are available as safety stops.
Magnetic sensors can be mounted on cylinder surfaces when input signals are required for controllers.
|
|
Twist Clamp Cylinders
Combines linear and 90-degree rotary motion with an internal pin/cam mechanism.
Rotary action moves a clamping arm away from the workpiece, allowing for easy loading and unloading of parts.
|
|
|
|
|
|
These products offers a wide range of traditional cylinders and innovative ones as well:
Cartridge Cylinders : Threaded piston rod, No-threaded piston rod. Bore size: 6 - 10 - 16.
Mini Cylinders Iso 6432: Single and Double-acting cushioned, Single or through piston rod. Bores: 8, 10, 12, 16, 20 and 25.
Mini Cylinders Inox ISO 6432: Double-acting magnetic; Double-acting without magnet. Bores: 16, 20 and 25.
Cylinders A95: Single and Double-acting cushioned; Single or through piston rod. Bore size: 32, 40, 50 and 63.
Compact Cylinders: Single and Double-acting magnetic; Single or through piston rod magnetic; Antirotation magnetic. Bore size from 12 to 100 mm.
Short Stroke Cylinders: Single and Double-acting magnetic; Single or through piston rod magnetic; Antirotation magnetic. Bore size from 12 to 100 mm.
Cylinder VDMA ISO 6431: Double-acting cushioned magnetic; Single-acting magnetic; Single or through piston rod magnetic; Tandem. Bores from 32 to 125 mm.
Rotary Cylinders : Double-acting cushioned and magnetic with male pinion; Double-acting cushioned and magnetic with female connection. Bores from 32 to 100 mm.
Magnetic Switches, Guide Units, Piston Rod Lock, Mounting Accessories.
|
|
Our Bansbach Feinmechanik AG Swiss facility manufactures special pneumatic cylinders and pneumatic accessories. Our Quality, Reliability and Durability is second to none!
Our contract manufacture business is the third main pillar of our company. Our customer's satisfaction is the Center point of this business. All products are customer specific and correspond exactly to the requirements of the application; even for very low quantities we maintain the highest quality cylinders.
Special pneumatic cylinders:
Custom products are designed, developed and manufactured according to the customer's request. That means we can help you with any application. Any project, Any time!
|
|
Standard Air Cylinders
* The "Original", with a "mirror finish" 304 stainless steel body, double-rolled end caps, sintered bronze rod bushing, Buna N "U" cup seals and our specially formulated HT-99 lubricant.
* Bore sizes: 5/16", 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3". Wide variety of mounting styles. Many standard catalog options: bumpers, extra rod extension, Magnalube® G lubrication, heavy spring, rotated ports, low and high temperature options, magnetic piston, rod wipers, no-thread rod and more!
* Quick delivery of catalog models -- we stock more than 150,000 and can make any catalog model in 5 days or less.
* If you need something a bit different than what's in the catalog, call us! More than half of our business is "special" cylinders that we designed for specific applications.
|
|
ISO Cylinders
Conforming to ISO 6431/6432 Standard Specifications, Bimba's ISO cylinders are designed to be easily interchangeable throughout the world. Bimba meets your needs.
Reliable service from a world-wide leader producing millions of actuators each year
Pre-lubricated for longer, maintenance free operation
Shock absorbing bumpers
Roll formed threads
High strength pistons permanently rivetted and sealed
Roller burnished stainless steel rods
Advanced bearing and seal materials for higher speed applications
Double rolled construction
Permanent mechanical retention; needles cannot blow out under pressure
Space savings available resulting from smaller external dimensions
Heads available i n Aluminium, Stainless Steel and Delrin®
Rapid design and delivery time for custom modifications
|
|
Original Pancake® Cylinder available in 8 bore sizes Multi-Position Series PD3
Square 1® Series Cylinder offers space saving design "F" Series Stainless Steel Body Cylinders
Global SeriesTM Cylinder is a true metric interchange Hi-PowerTM Cylinder offer strokes to 42"
"GT" Series Guided Toolplate Cylinder is based on the Global SeriesTM Cylinder LongstrokeTM Cylinder offer strokes to 42"
Pancake® II Standard Series PSD, PSR, PSX, PWD & PTD
NFPA Air Cylinders
Pancake® II Nonrotating, Twin Rod Series PND
Swing Clamp Cylinders
Stopper Cylinders
|
|
Diameter 10, 16, 20, 25, 32 mm
Stroke length 10 ... 100 mm
Force 94 ... 966 N
Position sensing
Fixed cushioning
Plain-bearing guide
Recirculating ball bearing guide
|
|
For simple tasks using a standard cylinder: the DNCB, latest member of the DNC family. Ideal in all applications where technically and functionally advanced drives are utilised.
• New piston system distinguished by extremely smooth running and significantly increased energy absorption
• Compatible with accessories and mounting attachments from the DNC modular system
• Diameters 32 ... 100 mm
• Strokes 2 ... 2,000 mm
• New precision adjustment with scale for end-position cushioning
|
|
High performance, long life, low maintenance: the top quality of Parker-Origa`s rod type cylinders is a result of decades of experience. Special customer specific solutions are part of our daily business.
Innovative cylinder concepts with excellent characteristics are the basis of the Parker-Origa cylinder programme. The inherent advantages are important factors for operation in system solutions. Modern automation with high efficiency is no longer a dream. Special solutions, which are developed for individual projects, guarantee optimal efficiency.
|
|
Air Cylinders with Adjustable Cushions
The Bimba Air Cylinders with adjustable cushions have a readily accessible cushion needle for easy adjustment, double acting models, and a 304 stainless steel body with mirror finish I.D.
High strength aluminum alloy porting ends and ground and roller burnished 303 stainless steel piston rods come standard. Also, the air cylinders have Buna N "U" Cup Seals, low breakaway friction - less than 5 PSI - and special stroke lengths available on request.
Air cylinders come in 3/4", 1-1/16", 1-1/2", 2", 2-1/2", and 3" bore sizes.
Bimba's cylinders with air cushions provide a possible solution to destructive energies. The air cushion traps a small amount of exhaust air at the end of stroke, providing an air pocket that decelerates the load. This reduces the potentially destructive energy being transmitted to the cylinder and other components.
|
|
|
Agroalimentary jack ICL Specific ISO 6431 Diameters: 32, 40, 50, 63, 80, 100 and 125 mm Races: 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500 (longer races on request) Corrosion resistant, including fixings Measurements according to the standards ISO Sensor easy to install and adjust
|
|
Extruded Flat Lift Table
EF1-based, guided cylinder with four shafts for maximum rigidity. It is designed for lifting applications where other non-rotating cylinders cannot handle an overhung load and space is at a premium.
Four-shaft support withstands offset loads and moments.
Simple, efficient design provides economical alternative to other costly guided actuators.
Joins the EF family of products, so shares all the same benefits--long service life, low friction operation, fast delivery.
Convenient wide tooling mounting surface.
Intended for vertical lifting applications (should not be mounted horizontally or with tooling plates facing down).
|
|
Z Line Air Cylinders
The Bimba Z Line Air Cylinders are for extremely tough applications.
The Z-Line air cylinder has the rolled-in construction of the Original Line but features the following: Larger diameter, two-piece 303 stainless steel piston rod HEX-STUD rod end thread of heat treated alloy steel - easily removed in case of failure due to overload, and cushion quiet elastomer bumpers.
No charge options include the Magnalube G, Molycoated body, and magnet.
Bore sizes for the Z Line cylinders are 3/4", 1-1/16", 1-1/2", and 2".
|
|
Hole Punch Cylinders
Designed to punch millions of holes in plastic or other thin sheet materials 2 to 3 mils thick, the long-life BIMBA Pneumatic Hole Puncher will give you more cycles per penny.
The hardened steel cutter with ground razor sharp edges is an integral part of the cylinder. A small air jet ejects the slugs from the cutter preventing slug build up, and Elastomer Bumpers insure cushion quiet operation.
Less than 1" in diameter, several cylinders can be closely mounted. Available in seven hole cutter sizes from 1 / 4 " to 5 / 8".
This stainless steel body, single acting spring return cylinder has a 3 / 4" bore and 1" stroke. A nickel plated steel rod guide is threaded for easy nose mounting, and a 1 / 8" NPT air inlet is conveniently located in the rear head.
Prelubricated with HT-99, the cylinder can be operated with ordinary shop air at pressures up to 250 psi.
|
|
MRS Cylinders
* The Bimba MRS® Magnetic Reed Switch Air Cylinders are specifically designed to operate Bimba position sensing switches to actuate programmable controllers, relays, solenoids, timers, or any other electrically operated equipment.
* MRS cylinders have an additional groove in the piston to accommodate a magnet. They differ from the Moption because they combine features of the "Z" line with Original Line construction. Type 303 stainless steel rods are standard.
* Options at no additional charge include Magnalube G, no thread, and switch track for standard reed switches.
* Bore sizes available are 9/16", 3/4", 1-1/16", 1-1/4", 1-1/2", 1-3/4", 2", and 2-1/2".
|
|
69-032/090-F
GENERAL CHARACTERISTICS
type of construction: with tie-rods
operation: double-acting
materials: AL tube and endcovers - NBR seals - other cementated steel
type of mounting: by means of holes in the body
type of mounting: any
Operating temperature: 0° + 50° C (with dry air -20°C)
standard rotation: 90° - 180° (others on request)
PNEUMATIC DATA
operating pressure: 0,5 -M0 bar
Fluid: filtered air, without lubrication
|
|
More reliability, more possibilities, more than just standard: modular round cylinder DSNU. A wide variety of variants and mounting options: the best solution for every application, both technically and economically.
• Diameters 8 ... 63 mm
• Stroke lengths 10 ... 500 mm
• X-strokes
• Standard types available from stock
|
|
Stopper Cylinders
EF1 Cylinder was modified for a conveyor stopping application.
Featuring a heavy-duty mounting, the cylinder's rod/bearing design was developed to withstand side impact loading.
Stroke lengths: 15, 20, 25mm.
Max Side Load: 12, 11, 10lb.
|
|
Rod Lock Cylinders
* The Bimba Original Line Rod Lock Cylinder is a normally clamped unit that holds the piston rod in position when air pressure is not present. It is ideal for preventing drift at machine shut-down.
* The rod lock air cylinder has dowel pins that ride in the cam groove. When air pressure is present, piston actuates and dowel pins follow cam to open position, allowing piston rod to travel freely through clamp. In the absence of pressure, the spring actuates the piston and dowels follow to closed position, activating the rod clamp.
* The Rod Lock is not a safety device. It cannot be used for intermediate stopping; the cylinder is designed to prevent drift from a stationary position.
* Load weight must not exceed the stated holding force for the cylinder.
* Bore sizes are 3/4", 1-1/16", 1-1/2 ", and 2".
|
|
|
Stroke is contained within the cylinder itself for space saving advantage. Allows force to be applied in both directions. Single acting, double acting, double purchase and track models available. Wide range for bore sizes and options
|
|
Ultran Rodless Cylinders
The Bimba Ultran rodless cylinder provides one of the highest coupling strengths available. This means it can carry higher loads without causing the piston to uncouple from the carriage.
Bimba also offers two magnetic coupling strength options (Gold and Silver) to suit a wide variety of applications. The Silver option uses two sets of magnets instead of three.
Bore sizes are 5/16", 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", and 2".
Bimba offers a model with built-in guides (Ultran Slide) and an unguided unit (Ultran).
Save space and streamline your design with the Bimba Ultran rodless cylinder! Application possibilities include transferring, feeding, door opening, cutting, silk screening and overall length savings.
|
|
Guiding cylinder
with two slide guides
with short slide guide
with safety unit
with slide guide underneath
Technical Information
· ZSS and ZKS have been designed for higher loads.
· By mounting a linear guide way on the bottom side of the cylinder, very high loads and moments can be carried forward
· Maximum stroke 3000 mm, longer on
· ZSS with two guiding carriages and a fitting length just like the ZS standard cylinder
· ZKS with a guiding carriage
|
|
The outstanding short-stroke cylinder. Space-saving - powerful - tried and tested. With sensor slots for SM..-8/SM..-10 proximity sensor.
• Diameters 4 ... 100 mm
• Stroke lengths 2.5 ... 25 mm
• Hole pattern to ISO 6431 for attachment for diameters 32 ... 100 mm
|
|
All Stainless Steel Non-Repariable Cylinder
Corrosion resistant 303 Stainless Steel end caps.
304 SS body with mirror finish ID for long, reliable seal life.
Urethane rod wiper designed to withstand exposure to harsh chemical solutions while limiting ingress of the solutions and application matter into the cylinder.
PTFE-based rod and pivot bushings selected for their resistance to many commonly used cleaning solutions.
Nitrile seals are standard with optional high temperature or other materials available.
|
|
All Stainless Steel Repairable (Bell Ring Style)
* The new all stainless repairable Original Line cylinders are ideal for food processing, chemical, medical, pharmaceutical, offshore or marine equipment, and energy production or waste management applications. The bell ring design also offers the added benefit of full repairability without the need for hand tools by securing the body to the rod guide with a knurled, threaded nut.
* Bore sizes for the all-stainless steel repairable cylinders are 3/4" and 1-1/16".
* Engineering specifications include 304 Stainless steel body, low friction Buna N "U" Cup seals and rod wiper, 303 Stainless steel endcaps, piston rod, and bell ring nut, and Composite FDA approved rod bearing and FDA approved lubricant.
|
|
The first friction-free cylinder: extremely smooth surface of Ra 0.6 µm, highly corrosionresistant and repairable.
• Diameters 32 ... 100 mm
• Stroke lengths 10 ... 500 mm
• Constructed from of stainless steel
• Rod wiper seal material PUR
• Fully repairable (cover connected to profile)
• Food industry approved lubricating grease (to USDA-H1) and piston rod wiper seal (to FDA)
|
|
|
|
