|
|
|
|
|
|
Current Rating: 3 amps max
Dielectric Withstanding Voltage:
600 VAC RMS
Insulation Resistance:
5000 Meg ohms min @ 500 VDC
Contact Resistance:
26 milliohms (65 mv) max @ 2.5 amps
Mating/Unmating Force:
Forces not to exceed 6 oz/contact
Temperature Cycling:
-55 ° C to +125 ° C, 5 cycles
Humidity (Mated):
IAW MIL-STD-1344, Method 1002.2, Type II, Omit Steps 7A & 7B
Vibration:
IAW-MIL-STD-1344, Method 205.1, Test Condition IV, 20 g's
Mechanical Shock:
IAW-MIL-STD-1344, Method 2004.1, Test Condition E, 50 g's
Durability:
500 cycles
Contact Resistance after Durability:
26 milliohms (65 mv) max @ 2.5 amps
Mating/Unmating after Durability:
Forces not to exceed 6 oz/contact
Salt Spray:
48 hrs IAW-MIL-STD-1344, Method 1001.1, Test Condition B
Low Level Contact Resistance after Salt Spray:
28 milliohms max (2.8 mv) max @ 100 milliamps
Contact Resistance after Salt Spray:
28 milliohms (70 mv) max @ 2.5 amps
Mating/Unmating force after Salt Spray:
Forces not to exceed 6 oz/contact
Contact Retention after Salt Spray:
Minimum of 5 lbs contact retention
Thermal Vacuum Out gassing:
NASA SP-R-0022
Solder Heat & Contact Retention:
360 ° C for 10 sec. & contacts must withstand 5 lbs retention force
Solder ability:
MIL-STD-202, Method 208
|
|
Audio Miniature Bayonet Lock Connectors
AB06 Series. AB06 connectors are a development of the established AB05 range and are particularly suitable for tinsel cordage applications in audio equipment.
Designed to the requirements of the Royal Signals and Radar Establishment, AB06 connectors are available in shell sizes 8, 10 and 12, and offer all the performance characteristics and design features of AB05 (Pattern 105) connectors. An alternative 'snatch' type coupling nut for quick release applications is available in shell size 10.
Accessories include straight polychloroprene sleeves for tinsel cordage, 90° outlets, and protective caps.
|
|
|
The small yet robust M8 x 1/Ø8 mm round connector is ideally suited for compact and space limited industrial applications. Please choose from pre-assembled and fully encapsulated versions, flange and field-wireable connectors, ranging from 3 to 6-pole versions.
|
|
|
Mencom Corporation manufacturers a full line of receptacles for mating with quick disconnect cord sets. The product line includes front mount, rear mount, PCB mount, through mount, and solder type receptacles. The receptacles can be ordered with either Metric, PG, or NPT threads.
|
|
|
The quick-connect S12 x 1 is fully compatible with your terminals. You can replace the standard M12 round connector easily without having to adapt the complement. The S12 x 1 is a quick and safe solution for your industrial application.
|
|
QUIK-LOC 600 VOLT CONNECTORS
Electrical Parameters
3 or 4 contacts; with or without pilot circuit contacts. #8 AWG through 500 MCM cable. Up to 600 Volts; 625 Amps.
The Quik-Loc Connector was designed for service under the most severe mining conditions. Constructed of resilient neoprene and sturdy neoprene covered alloy castings, it is tough, watertight, corrosion-resistant — practically indestructible.
ELECTRICAL PARAMETERS 3 POWER GROUND AND 2 PILOT CONTACTS, #8 THROUGH 500 MCM CABLE UP TO 1000 VOLTS; 500 AMPS.
|
|
|
150°C round connector by ESCHA. Thermal load is an increasingly relevant issue concerning modern machines and systems. In order to comply as well with requirements in the field of connection technology, ESCHA has developed a new family of round connectors which sets standards with respect to thermal load. A permanent service temperature between -20°C and +150°C enables a broad ranged application without additional protection against high temperatures. Beyond the permanent service temperature, extreme thermal loads of up to +200°C in the application can be tackled. For the standard housing types M8x1 and M12x, ESCHA developed different polarities in order to offer a comprehensive solution with the new product family. The new connector type features degree of protection IP65 and thus fulfills the requirements of your application .
|
|
| ... products without technical information |
| |
|
|