|
|
MODEL SERIES - DC30
PMDC GEARED MOTOR
Design - Motor DC30 is a carbon brush DC motor which is used in combination with many MechTex gearheads. The standard gearheads used in conjunction with this motor are GB2,GB5P, GB5H, GB38OCP, GB3, GB4, GB7,GB8 & GBW. Depending on the application, output speed, load applied, etc. the type of gearhead can be selected. Various types of gears i.e. poly acetal, sintered iron, brass or
steel gears can be used based on the requirement. Poly acetal or sintered gears damp the noise. Case hardened steel gears are always on the output for load considerations. Complete poly acetal gears are used when the output torque
required is low. Linear drive is possible with gearhead GB4, GB7, GBW with M6 x 1 mm pitch screw. The linear guide & screw arrangement can be done only on special request.
|
|
MODEL SERIES - DC33
PMDC GEARED MOTOR
Design - Motor DC33 is a carbon brush DC motor which is used in combination
with many Mech Tex gearheads. The standard gearheads used in conjunction with this motor are GB2, GB5P, GB5H, GB38OCP, GB3, GB4, GB7, GB8 & GBW. Depending on the application, output speed, load applied, etc. the type of gearhead can
be selected. Various types of gears i.e. poly acetal, sintered iron, brass or steel gears can be used based on the requirement. Poly acetal or sintered
gears damp the noise. Case hardened steel gears are always on the output
for load considerations. Complete poly acetal gears are used when the output
torque required is low. Linear drive is possible with gearhead GB4,GB7,GBW
with M6 x 1 mm pitch screw. The linear guide & screw arrangement can be
done only on special request.
|
|
MODEL SERIES - DC28
PMDC GEARED MOTOR
Design - Motor DC28 is a carbon brush DC motor which is used in combination with many Mech Tex gearheads. The standard gearheads used in combination with this motor are GB2, GB5P, GB5H, GB38OCP, GB3, GB4, GB7, GB8 & GBW. Depending on the application, output speed, load applied, etc. the type of gearhead
can be selected. Various types of gears i.e. poly acetal, sintered iron, brass or steel gears can be used based on the requirement. Poly acetal or sintered gears damp the noise. Case hardened steel gears are always on the output for load considerations. Complete poly acetal gears are used when the output
torque required is low in an economical model (GB7P). Linear drive is possible with gearhead GB4, GB7, GBW with M6 x 1 mm pitch screw. The linear guide & screw arrangement can be done on special request.
|
|
MODEL SERIES - DC32
PMDC GEARED MOTOR
Design - Motor DC32 is a carbon brush DC motor which is used in combination with many Mech Tex gearheads. The standard gearheads used in conjunction with this motor are GB2, GB5P, GB5H, GB38OCP, GB3, GB4, GB7,GB8 & GBW. Depending on the application, output speed, load applied, etc. the type of gearhead can be selected. Various types of gears i.e. poly acetal, sintered iron, brass or
steel gears can be used based on the requirement. Poly acetal or sintered gears damp the noise. Case hardened steel gears are always on the output for load considerations. Complete poly acetal gears are used when the output torque
required is low. Linear drive is possible with gearhead GB4,GB7,GBW with M6 x 1
mm pitch screw. The linear guide & screw arrangement can be done only on special request.
|
|
MODEL SERIES - DC25
PMDC GEARED MOTOR
Design - Motor DC25 is a precious metal brush DC motor which is used in combination with many Mech Tex gearheads. Conjunction with this motor are GB2, GB5P, GB5H, GB38OCP, GB3, GB4, GB7, GB8. Depending on the application, o/p speed, load applied, etc., the standard gearheads used in the type of gearhead can be selected. Various types of gears i.e. poly acetal, sintered iron, brass or steel gears can be used based on the requirement. Poly acetal gears damp the noise. Case hardened steel gears are always on the output for load considerations. Complete poly acetal gears are used when the output torque
required is low. Linear drive is possible with gearhead GB4, GB7 with M6 x 1 mm pitch screw. The linear guide & screw arrangement can be done only on special request.
|
|
MODEL SERIES - DC42/ DC52
PMDC GEARED MOTOR
Design - Motor DC42/DC52 is a heavy duty carbon brush DC motor which is used in combination with GBW gearhead only. Gearhead GBW contains heavily loaded steel gear wheels. The spur gears are fixed on steel spindles which are hardened and polished to a mirror finish & rotate in sintered bushings. The thick output shaft rotates in robust sintered bushings. All the gears are housed in between metal plates & closed by plastic dust cover. All bearings are permanently lubricated and therefore require no maintenance. Linear drive also possible on request.
|
|
MODEL SERIES - GEARED MOTORISED POTENTIOMETERS
DC MOTORS WITH POT ASSEMBLY
Design -
Mech-Tex offer various assemblies in which a potentiometer with different gear ratios can be mounted in series of the gear train. Thus the geared DC motor operation can be convert in to a close loop one. Suitable mounting arrangement to mount the potentiometer on the gearhead is provided. Use of suitable reduction gear ratios can make the potentiometer rotate more or less (as per requirement) number of rotations with respect to the output shaft. Thus the reading provided by the potentiometer can be more accurate.
|
|
5inch BZD Serial Pump DC Motor
Voltage : 12-48 V
Power : 2300 - 3000 W
Direction : CW, CCW
Rated Current : 2800 - 3450 rpm
O.D. : 125 mm
BZD-3.3 Serial Pump DC Motor
Voltage : 24 V
Power : 3300 W
Direction : CW, CCW
Rated Current : 3350 rpm
O.D. : 126 mm
4.5inchBZD Serial Pump DC Motor
Voltage : 12-48 V
Power : 1500 - 2500 W
Direction : CW
Rated Current : 2300 - 2600 rpm
O.D. : 114 mm
Small Serial Pump DC Motor
Voltage : 12-24 V
Power : 300 - 1200 W
Direction : CW, CCW
Rated Torque : 1.5 - 3.5 Nm
Rated Speed : > 1430 - 4000 rpm
O.D. : 84 mm
|
|
ISM Micro-Power Data Transmission I/O Module FC-201S
¡ôShort-distance wireless data transmission
¡ôAutomatic data collection system
¡ôWireless meter reading
¡ôIndustrial remote control and remote measurement
¡ôBuilding automation, safety and security, powerhouse equipment wireless monitor, entrance control system
Specifications:
1) Carrier frequency: 433MHz
2) FSK Manchester
3) Frequency stability: ¡À5ppm
4) Channel: 8
5) Wireless I/O function, 4-input/ 2-output, addressing range: 0000 - 9999
6) RF power: ¡Ü20mW
7) Receiving sensitivity: ¡Ü-105dBm
8) Transmitting current: ¡Ü 70mA
9) Receiving current: ¡Ü 20mA
10) Interface: RS-232/ RS-485/TTL (customization for one of the three), data rate:1,200 - 19,200bps, format: 8E1/8N1/8O1
11) Air data rate: 1,200 - 19,200bps
12) Power supply: DC 3V¡À0.3, 5V¡À0.5
13) Temperature: -25¡ãC to +60¡ãC
14) Dimensions: 48 x 33 x 12mm
|
|
|
|
|
|
Radio Telemetry Transceiver FC-201/B
Features
1. Dual PLL and dual VCO.
2. Advanced modulation mode MSK for reliable data transmission.
3. The working frequency covers 20MHz.
4. Store 16 receiving /transmitting channels.
5. Operating in multiple communication protocols with high compatibility.
6. Providing RS-232/RS-485/UART(TTL level) interface, easy to connect with various equipments.
7. Built-in software watchdog to ensure long-time reliable work.
8. SMT assembly, high integration and advanced technics.
9. Modularized design for convenient embedding.
Specifications:
1) Carrier frequency: VHF/UHF
2) FFSK
3) Channel spacing: 25kHz/12.5kHz
4) Channel: 16
5) Frequency stability: ¡À5ppm
6) Interface: RS-232, data rate: 1,200 ~ 9,600bps optional, format: 8N1/8E1/8O1
7) Air data rate: 2,400/1,200bps
8) Antenna impedance: 50¦¸
9) Temperature: -20 ~ 60¡ãC
10) Weight: 150g (antenna port included, heat sink excluded)
11) Size: 106 x 54 x 18mm (antenna port and heat sink excluded)
Receiver:
1) Receiving sensibility: ¡Ü0.25¦ÌV(12dB SINAD)
2) Adjacent channel selectivity: ¡Ý65dB
3) Frequency deviation: ¡Ü¡À5.0kHz
4) Clutter and images rejection ¡Ý65dB
5) Intermodulation rejection ratio: ¡Ý65dB
6) Audio distortion: ¡Ü3%
7) Standby current: ¡Ü60mA
Transmitter:
1) RF power: ¡Ü5W
2) Adjacent channel rejection: ¡Ý65dB
3) Audio distortion: ¡Ü3%
4) Transmitter startup time: ¡Ü50ms
5) Power supply: 9 ~ 15V DC, 13.8V typical
6) Transmitting current: ¡Ü2.0A (13.8V, 5W)
|
|
|
|
|
|
Data Transceiver FC-228 Features:
1. Frequency : 223MHz -235MH,450-470MH
2. Muti-Channels : The standard FC-228configuration provides 16channels, meeting the multiple communication combination mode of the user.
3. 3FSK Modulation : high-efficiency encoding technology
4. High Sensitivity: used high performance narrow-band chip to realize high receiving sensitivity.
5. Adjustable Bandwidth: user can adjust bandwidth among 5KHz12.5KHz18.75KHz and 25KHz
6. Adjustable power:5W/10W/15W/20W/25W
7. Abnormal Frequency Technology:The transmission and reciveing of FC-228 can work on different frequency and the channel can also exchange.
8. Safe and Reliable data transmission:adopt M series encryption and CRC32 checksum to ensure safety and reliability of data on air transmission.
9. Interface modes: FC-228 can provide three interface RS-232,RS-485 and TTL.
10. Muti Data Rate: user can set according to its system interface data rate base on 1200bps,2400bps,4800bps,9600bps,19200bps.
Technical specification:
1Power supply +12V ---+14V
2Standby current :≤80MA
3RX current :≤100 MA
9.TX current :≤6A
3Operating temperature : -40--+85
5.Channel spacing :25KHZ
6.Modulation : 3FSK
8.RF output power :25W±1W
10.Frequency :±500HZ
|
|
Specifications:
1)Frequency Band : UHF/VHF (400-470MHz 136-174MHz)
2)Channel Spacings:25KHz,12.5KHz programmable
3)RF Output Power:1W / 5W Programmable
4)Modulation type :16K0F3E ,8K5F3E
5)Intermediate Frequency: 45.1MHz&455KHz
6)Number of Channels:16
7)Frequency Source :Synthesizer
8)Operation Rating:Intermittent 5:5:90 ( TX: RX: Standby)
9)Power Supply:12.5V DC Nominal Voltage
10)Temperature Range
11)Storage:from -40¡ãC to +80¡ãC
12)Operating:from -30¡ãC to +60¡ãC
13)Current Consumption
14)Standby (Muted): ¡Ü40mA
15)Transmit 5 Watts RF Power :< 1.5A
16)Transmit 1 Watt RF Power:<0.8A
17)Frequency Bands :RX UHF: U1 400 470 MHz
TX UHF: U1 400 470 MHz
18)Dimensions: (120mm)L * (60mm)W * (20mm)H
19)Weight: ¡Ü150 grams
|
|
FC-201/SA Audio/Data RF module
Application:
¡ôWireless meter reading
¡ôIndustrial remote control and telemetry
¡ôAutomatic data collecting system
¡ôBuilding automation, safety and security, powerhouse equipment wireless monitor, entrance control system
¡ôPOS system, wireless keyboard, mouse
¡ôTraffic, under-well locating ,alarm
Specifications:
Modulation mode£º MSK
Carrier frequency£º UHF/VHF
Frequency stability£º ¡À2.5PPM
RF power£º 200mW /300mW optional
Channel Spacing: 12.5kHz/25kHz
Receiving sensitivity£º-119dBm
Interface data rate£º 1200¡«9600bps
Interface data format£º 8E1/8N1/8O1
Air data rate£º1200¡«9600 bps
Temperature£º-20¡æ¡«70¡æ(Ordinary)
-35¡æ¡«70¡æ(Industrial )
Power supply£º DC +3.6¡« 5.0V
Dimension: 61.5mm¡Á36mm¡Á12mm
Weight: 30g
Transmitting current£º ¡Ü200mA
Receiving current£º ¡Ü40mA
Humidity£º 10%¡«90%RH£¬non-condensing
|
|
FC-203/SA Audio/Data RF module
Frequency: VHF/UHF
Channel spacing 25KHz/12.5KHZ
RF Power 2W
Modulation 16K0F3E,8K5F3E
IFfrequency 1st IF45.1MHz & 2nd IF 455KHz
Channels.16
Power supply: 8VDC
Temperature
Storetemperature: 40°Cto +80°C
Workingtemperature: 30°C to +60°C
Current
RX current ≤35mA
TX current < 800mA
Dimensions.(75mm)L x (45mm)W x (12.5mm)H
Weight ≤45.5g
Frequency stability.±2.5 ppm
Sensitivity(12dB Sinad) .<-119dBm,
TX to RX < 20ms
RX to TX ....< 45ms
Modulation Type------------------------FSK
Interface data rate-------------------- 9600bps
Interface data format-----------------8E1/8N1/8O1
RF data rate----------------------------- 9600 bps
|
|
Data Transceiver /RF Radio FC-221AG
1) Comply with FCC&CE
2) PLL & TCXO
3) 25KHz /12.5KHz channel spacing
4) 19.2kpbs RF data rate
Application:
Wireless AMR system;
Wireless data collection;
Industrial control and telemetry;
Wireless queuing system;
wireless weighting scales;
Security monitor and alarm;
LED sign automatic display;
Specification :
1) Frequency band: 433MHz(default),868MHz,915MHz
2) 3FSK
3) Channel: 8, customized for more channels.
4) RF Power: <50mW
5) Receiver sensitivity: -118dBm@1200bps,-115dBm@2400bps
6) Transmit current:<45mA/TTL,<51mA/RS485,<52mA/RS232
7) Receive current:<30mA/TTL,<35mA/RS485,<35mA/RS232
8) Sleep current: 25uA
9) Cgannel spacing:25kHz
10) Interface: UART/TTL,RS-232,RS-485,Baud rate: 1200-19200bps.
11) RF data rate: 1200-19200bps
12) Power Supply: 5.0±0.5V DC(customzide for 12V)
13) Temperature: -30°C ~ 80°C
14 )Size:40mmx27mmx6mm
15) Weight: 10g
|
|
High speed Data transceiver/ data radio/ FC-222
Technical specification:
Frequency band: VHF/UHF, default band: 220MHz
Modulation : 3FSK
Channel spacing 5KHz12.5KHz18.75KHz and 25KHz optional.
Three interface RS-232,RS-485 and TTL optional.
RF Data Rate: 1200bps,2400bps,4800bps,9600bps,19200bps optional.
Power supply :+10.5V +15.0V,Nominal voltage +13.8V
Standby current :¡Ü80MA
RX current :¡Ü100 MA
TX current :¡Ü1.6A
Operating temperature : -40+85
Channel spacing :5KHZ
Modulation : 3FSK
RF output power :5.5W¡À0.5W
Frequency deviation :¡À500HZ
RX sensitivity : ¡Ü-118dBm1200bps.
|
|
Powerful traction
Available with lsuzu engines
Low center of gravity for better stability
Flexible operation with numerous optional attachments available
Simplified maintenance
|
|
Class Name：Electric forklift trucks->Three-wheel electric forklift trucks
AC Electric Three-wheel Forklift Trucks 1-1.5T
Model : CPD10S-CQ
Load Capacity : 1000 kg
Load Centre : 500 mm
Service Weight Including Battery : 2900 kg
Overall Length(Without forks) : 1784 mm
|
|
Class Name：Electric forklift trucks->Four-wheel electric forklift trucks
AC Electric Forklift Trucks 4-4.5T
Model : CPD40-A2
Load Capacity : 4000 kg
Load Centre : 500 mm
Service Weight Including Battery : 6450 kg
Overall Length(Without forks) : 2705 mm
|
|
Class Name：Electric forklift trucks->Electric powered reach forklift trucks
Electric Reach Truck-sit-down Type 1.6-2.0T
Model : CQD16S-B2
Load Capacity : 1600 kg
Load Centre : 600 mm
Lifting Speeds : 260/380
Standard Lift Height : 4250 mm
|
|
| ... products without technical information |
| |
The product is filled by a dosing auger that is designed depending on the product characteristics. The flexibly adjustable auger rotation speed guarantees a high filling accuracy even if it comes to the filling of the most diverse
For the compact filling of heavily fluidised products a de-aeration system can be integrated in the auger housing. Thanks to the resulting high compacting rate the auger packer produces robust and easily stackable bags.
Advantages of the auger packer:
- product-specific design of the dosing auger
- quick and efficient cleaning due to the divided dosing auger
- filling of paper and PE bags with low de-aeration properties
Machine output of the auger packer:
up to 150 bags per hour per spout
|
|
The TOPLINE has been especially developed for powdery products, just as flour, starch, baking ingredients, yeast, etc. as well as pet food.
All necessary steps from the filling up to the closing of the open-mouth bags take place in the compact cabinet of the TOPLINE. After the empty bag has been taken out of the bag magazine and opened it is exactly placed at the filling spout. During the filling clamping jaws grab the bag from all sides in a secure and dust-tight way. The filled and compacted bags are closed by either sewing, folding, sealing and/or hot melt activation.
Advantages:
- clean product filling
- high bag filling degree
- clean packing environment and compact packing room due to the integration of all necessary filling and closing modules in one cabinet
- empty and full bag transfer at the same height during the complete filling and closing cycle
Machine output:
200 - 800 bags per hour for filling weights from 10 to 25 kg
|
|
The "Plug 'n Pack" concepts made by BEHN + BATES unify the applicator, filling and sealing technology in one compact, pre-assembled and dust-tight unit that ensures a low-noise filling operation and shortest assembly times as the test operation is carried out in our workshop already.
Our "Plug 'n Pack" concepts can be integrated even into smallest spaces.
|
|
Electronic Weigh Packer
FNL-306CC
Main user
Food industry, Pharmaceutical industry, Agricultural chemical company, Petrochemical industry, Feed manufacturing plant, Ceramics industry.
Features
- Compact
With only 80% of previous models height, the FNL-306CC can be installed in a small space. (Comparison with Yamato FNL-306CC)
- Simple construction for easy cleaning and maintenance
The single-plate cutoff gate is directly linked to the servomotor to make adjustment of the opening angle simple. Maintenance and cleaning are simple and contamination is eliminated.
- New feed method increases weighing speed
The new digital servo-feed system achieves high-speed feeding and weighing operation at 700 bags per hour.
|
|
Once the filling process has been initialzed, depending on the chosen type of the big bag filling station, all of the functions are carried out automatically.
The ventilation and densification of the products are decisive during the coarse flow or after the end of the filling process to ensure the optimum filling output and stability of the big bags. The densification can be carried out by an integrated vibrating device or an integrated de-aeration probe. The optimum densification parameters can be set according to the specific product properties.
Advantages:
- dust-free filling thanks to the sealing of the inflatable sleeve
- product-specific dosing organ
- user-friendly with its pneumatically operated and slewing clamping hooks
- blow device for the optimum forming of the big bags
Machine output:
up to 30 bags per hour
|
|
Efficient and reliable filling of floury, powdery and gritty products, just as starch, flour, baking ingredients, soybean products, proteins, sugar, etc.
For product filling the pneumatic packer utilises air. The proven design of the chamber bottom and top fluidisation air supplies that are separately adjustable depending on the flow behaviour of the product provides an optimum product feed rate with a minimum air supply.
Thanks to the continual air suction during the filling, high filling outputs are guaranteed with a minimum internal bag pressure.
Advantages of the pneumatic packer:
- gentle, clean and low-dust product filling
- minimised product residue in the filling chamber
- easy cleaning in case of product change
- project-specific configuration thanks to the BEHN + BATES modular system
Output of the pneumatic packer:
up to 300 bags per hour per spout
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
