|
|
ALMATEC's A-Series made of plastic has been developed on the basis of extensive experience in the production of pneumatic diaphragm pumps and offers numerous advantages meeting market requirements.
Six sizes with max. delivery volumes of
0,6 m³/h (A 08)
1,2 m³/h (A 10)
3 m³/h (A 15)
6 m³/h (A 25)
18 m³/h (A 40)
32 m³/h (A 50)
make it possible to choose exactly the right pump for the specific application.
A variety of materials is available for the A-Series pumps:
Housing - PE, PE conductive, PTFE, PTFE conductive
Diaphragms - EPDM, PTFE/EPDM
Ball valves - EPDM, PTFE, stainless steel
Cylinder valves - PE, PTFE
A-Series pumps made of PE conductive and PTFE conductive meet the ATEX requirements of the directive 94/9/EG.
|
|
For a pump that can pass the acid test, consider the Marathon® M Nonmetallic Pump Series. Rugged, all-bolted construction. No clamps. Models in PVDF, Nylon, Conductive Acetal and Polypropylene. Specially-coated, chemically-resistant hardware. Optional spill containment and leak detection.
Product range from:
Pipe Size: .25" / 6mm
Displacement Per Stroke: .01 gal / .04 ltr
Max. Flow per Minute: 4 gal / 15 ltr
Max. Solids Handling: .03" / 1mm
Max. Discharge Pressure: 100 PSI / 6.9 BAR
To:
Pipe Size: 3" / 80mm
Displacement Per Stroke: .9 gal / 3.41 ltr
Max. Flow per Minute: 238 gal / 901 ltr
Max. Solids Handling: .71" / 18mm
Max. Discharge Pressure: 100 PSI / 6.9 BAR
|
|
The bellows pump is a pneumatic, self-priming pump. The fluid is pumped between the two chambers, airside and liquidside. This pump is adact for to transfer of ultrapure acids and solvents used in the semiconductor industry.
Their pumping frequency is much lower than an equivalent diaphragm pump and results in an extended life. Due to this low frequency and amplitude of the bellows pump, we guarantee a lower level of particle contamination. All PFD pump wetted components are manufactured with TEFLON® (PFA HP, PTFE and FEP). All other components are manufactured with high technology materials; e.g. PVDF and PEEK.
The use of material chemically inactive allows no ionic contamination. This pump is assembled in cleanroom.
Flow rate: 20 l/min
Max. suction head: 3,5 m
Max. air pressure: 5 bar
Max. back pressure: 4 bar
Max. air consuption: 13,5 m^3/h
Max. air connection: 4 mm I.D.
Weight: 4 kg
|
|
| ... products without technical information |
| |
The J+J electric actuator is widely used in the plastic valve market because it has a plastic housing making it light in weight, and as it has more standard features than any of its rivals, offers exceptional value.
The new J3 Series electric actuators offer an LED status light and plug & play conversion kits that change the function from on-off to failsafe, or modulating, or both.
|
|
|
Cam-Line plastic-lined trunnion ball valves offer the same proven design benefits as the Cam-Tite product line, including tight shut-off, reliable stem sealing, and unsurpassed torque reduction—all unique features in a plastic-lined ball valve design. With special Tefzel or polypropylene linings and option PVDF coatings, Cam-Line ball valves are well suited for highly corrosive applications within the chemical processing industry such as sulfuric and hydrochloric acid.
|
|
Rugged, Compact Design:
Hayward's rugged, low cost QIC2 all plastic PVC ball valves incorporate many design features found only on higher cost ball valves. Features such as PTFE seats, full porting and a 150 PSI pressure rating are all standard on every size of QIC2 ball valves.
Cost Sensitive Applications:
The QIC2 ball valve is perfect for OEM and other applications that require a reliable ball valve at an economical price. The QIC2 valve has been designed and tested to make certain it will perform year in and year out in the most demanding applications without leakage or failure. The internal components of the QIC2 ball valve are completely encapsulated inside the one piece valve body which means that the valve never requires adjustment. The QIC2 valve is ready to be put into service right out of the box.
Lightweight and Compact:
QIC2 lowcost ball valves are designed to fit into spaces too small for other valves. They are about 1/3 the overall size of a true union ball valve and they weigh an average of 50% less. This makes them ideal for skid mounted and other applications where space and weight are critical considerations.
Can't Rust, Won't Corrode:
Their all plastic construction means that they will never fail, stick, or jam because of rusted or corroded parts. And they'll work in places and environments where metal valves must be painted or coated just to survive.
|
|
The VKD is a True Union ball valve, particularly suitable for industrial applications, where high performances and long time reliability are a must.
The patented Seat Stop® system assures great longevity of the seals in situations where vibration or thermal expansion occurs. A micro-adjusting of the PTFE seals is also allowed.
As any accidental loosening of the ball carrier is not possible, the radial dismounting of the valve body can be done in full safety.
The new patented Dual Block® system allows a proper nut tightening, without any risk for unscrewing due to vibrations.
|
|
Design Features:
- Shown with KZCO's EH2 low voltage electric actuator
- 3/4" to 2" Full Port Single Valves
- Max PSI 150 @70F (Poly)
- Max PSI 300 @70F (Nylon)
- Wiring (most configurations available)
- NEMA 6P Actuator housing
- Ball: 316 SS
- Stem: 316 SS
- Valve Body: Polypropylene or Nylon
- Seat: Virgin PTFE
- Stem Seal: Dual VITON O-Ring
- Body Seals: EPDM
- FNPT or Flanged outlets available
- Quick Hairpin (QH)(1" Only)
|
|
The VKD is a True Union ball valve, particularly suitable for industrial applications, where high performances and long time reliability are a must.
The patented Seat Stop® system assures great longevity of the seals in situations where vibration or thermal expansion occurs. A micro-adjusting of the PTFE seals is also allowed.
As any accidental loosening of the ball carrier is not possible, the radial dismounting of the valve body can be done in full safety.
The new patented Dual Block® system allows a proper nut tightening, without any risk for unscrewing due to vibrations.
|
|
In the field of drying, Piovan has developed the application of an innovative technology: the use of a rotor with a honeycomb structure to eliminate the humidity released by plastic material during the drying process.
This brand-new series, presented for the first time at the K2007 show, consists of four models that operate in a temperature range from 80 to 150°C, with air flows from 50 to 200 m³/h: HR50, HR100, HR150 and HR200.
The new HR dryers present numerous advantages such as:
• No expense for the connection of cooling water or compressed air and no running costs for such services because the HR units require only electric power supply;
• 50% reduction of the use of energy;
• Stable Dew Point, featuring set-up values in a range down to -50°C;
• Easy access to all machine components allowing Simplified maintenance
• Guaranteed absence of dust and of material contamination, making the HR dryers suitable for application in the medical and optical sectors too;
• Continuity of operation of the honeycomb rotor ensured by the new drive mechanism furnished with a wear-resistant Kevlar reinforced belt which eliminates traditional maintenance operations or lubrication, necessary when using rudimental belts or chains.
|
|
DRYMAX D30, D60 and 100 Compact Dry Air Dryers
The DRYMAX Series dry air dryers are equipped with two desiccant beds to supply continuous
dry process air and constant quality for the perfect drying of plastic resin.
- Ambient Independent Dew Point to -60°C
- Motorized Switchover Valve – Operation without compressed air lines and optimized control of drying and regeneration cycles in both desiccant beds.
- Energy Saving Counter Airflow Regeneration – Reduced energy costs through fastest dehumidification of the desiccant beds during the regeneration phase.
- Material Protection Function – Avoids over-drying and thermal degradation of the plastic resin through short term lowering of the drying temperature during the production stoppages of the processing machine.
– Micro Particle Filter in Return Air – Dust separation efficiency of up to 99.9% for high process safety.
- SmartReg Energy Saving Function – For the time optimized control of regeneration and cooling of the desiccant beds (on DRYMAX D60 and 100).
- SmartFlow Intelligent Air Distribution – Automatic air distribution to adjust to different materials and fluctuating material demands (available on units with 2 drying hoppers).
|
|
SOMOS®
- Plastic Analyser
The Plastic Analyser serves to define and monitor the material properties of free-flowing plastic bulk materials. The moisture content or filler content are determined by the relationship between the electrical performance characteristics and the specific composition of the plastic in this process for example. The Plastic Analyser can be employed as a permanent component of a processing machine (a granule extrusion system, for instance) or as an auxiliary unit for intermittent operation (during inspection of incoming shipments, for example).
|
|
| ... products without technical information |
| |
Our company is specialized in design and construction of NUMERICAL CONTROL MACHINING CENTRES 3, 4, 5 axis for cutting and machining soft materials (aluminium, composites, plastic, wood).
Ranges of application are extremely different (aeronautics, automobil and plastic industries, appearance cover, houseold furniture, naval construction, shaping, molds and patterns...).
Our range represents single and multispindle machines with and without automatic tool changers.
Standard capacities from 2000 mm x 1000 mm to 40 metres x 6 metres.
Machines are designed with :
- moving gantry and fixed table for long products,
- fixed gantry and one moving table for smaller components and two moving tables for higher productivity.
- overhead moving gantry.
High velocity movements due to brushless or linear motors combined with high speed spindles allow increased productivity. The installation of an automatic Tool Changer or multi-spindles also allows the regrouping of different operations within the same machining area.
The efficiency increases by a connection between your CAD system and CRENO CAD CAM softwares :
- complexe 5 axes machine(mould or triming)
- nesting software for optimizing the use of material.
We trust our product range is of interest to you, please do not hesitate to contact us for any further information.
|
|
Our company is specialized in design and construction of NUMERICAL CONTROL MACHINING CENTRES 3, 4, 5 axis for cutting and machining soft materials (aluminium, composites, plastic, wood).
Ranges of application are extremely different (aeronautics, automobil and plastic industries, appearance cover, houseold furniture, naval construction, shaping, molds and patterns...).
Our range represents single and multispindle machines with and without automatic tool changers.
Standard capacities from 2000 mm x 1000 mm to 40 metres x 6 metres.
Machines are designed with :
- moving gantry and fixed table for long products,
- fixed gantry and one moving table for smaller components and two moving tables for higher productivity.
- overhead moving gantry.
High velocity movements due to brushless or linear motors combined with high speed spindles allow increased productivity. The installation of an automatic Tool Changer or multi-spindles also allows the regrouping of different operations within the same machining area.
The efficiency increases by a connection between your CAD system and CRENO CAD CAM softwares :
- complexe 5 axes machine(mould or triming)
- nesting software for optimizing the use of material.
We trust our product range is of interest to you, please do not hesitate to contact us for any further information.
|
|
Our company is specialized in design and construction of NUMERICAL CONTROL MACHINING CENTRES 3, 4, 5 axis for cutting and machining soft materials (aluminium, composites, plastic, wood).
Ranges of application are extremely different (aeronautics, automobil and plastic industries, appearance cover, houseold furniture, naval construction, shaping, molds and patterns...).
Our range represents single and multispindle machines with and without automatic tool changers.
Standard capacities from 2000 mm x 1000 mm to 40 metres x 6 metres.
Machines are designed with :
- moving gantry and fixed table for long products,
- fixed gantry and one moving table for smaller components and two moving tables for higher productivity.
- overhead moving gantry.
High velocity movements due to brushless or linear motors combined with high speed spindles allow increased productivity. The installation of an automatic Tool Changer or multi-spindles also allows the regrouping of different operations within the same machining area.
The efficiency increases by a connection between your CAD system and CRENO CAD CAM softwares :
- complexe 5 axes machine(mould or triming)
- nesting software for optimizing the use of material.
We trust our product range is of interest to you, please do not hesitate to contact us for any further information.
|
|
With its ranges WINNER and NORMAPROFIL, MECANUMERIC offers to you various solutions for the applications of machining 5 axes.
Range NORMAPROFIL is intended for the machining of large thermoformées parts, rotomoulées, injected, and the manufacture of moulds and large-sized models.
The range WINNER which uses the architecture of the fixed gantry with a mobile table will be used for the applications of machining 3D of precision.
Many formats useful (X, there, Z) since 1000 X 700 X 600 mm for 3750 X 2250 X 1380 Misters.
|
|
Machining centres of the M 7/MM 7 series are designed for highly dynamic
finishing of moulded parts and panel components made of aluminium,
thermoplastics or duroplastics as well as for the machining of hard foam
blocks. The machine concept stands for highly dynamic rigidity and meets the requirements for top machining quality with maximum feed rates.
This series guarantees availability and economic efficiency thus being profitable even for users with small-quantity production. The tandem table technique allows alternating operation and minimizes downtimes for loading and unloading of the workpieces. Both tables can be coupled for the machining of large workpieces.
|
|
For materials like as Nomex, Kevlar, Aluminium usw.
Shafts / receptions.
Circle-knives.
Special-circular saw-leaves.
|
|
|
|
see the results for the following category
