|
|
RD5 Series
Rotary diaphragm pump
An eccentrically mounted bearing on the shaft, rotates within a flexible diaphragm. As the shaft rotates, the bearing flexes the diaphragm, squeezing the liquid through the pump.
|
|
Savino Barbera snc offers the new series of double diaphragm air driven pumps
Using such alternate and selected materials for the diaphragms, these pumps can be used with the major part of aggressive liquids, and can also run dry.
General specifications:
Materials: PP, PVDF, aluminium, stainless steel
Pumping of viscous fluids with air or gas (paints, resins, inks, fuels, glues, oils, juices, soaps…) or with abrasive particles
Self-priming: no internal sealing systems allows dry running without damaging the pump.
Explosion-proof
|
|
Double Diaphragm Vacuum Pumps and Compressors for greatly increased safety
The double diaphragm pumps: especially suitable where safety and gas tightness are essential, e.g., with toxic, radioactive or particularly expensive gases.
|
|
PTFE Diaphragm pump B85 T
Contamination free pumping
The B85T vacuum pump/ compressor is designed for use with corrosive gases and vapours.
|
|
Temperature-resistant and heated Diaphragm Vacuum Pumps and Compressors
Uncontaminated transfer of air and neutral, slightly aggressive gases and vapours at temperatures of 240 °C. Heating prevents condensation of gas. Versions with electronic temperature control.
|
|
Dry running diaphragm pump. Two different means of actuation: linear and vibration armature. Very high life time, low noise level, and high efficiency. Used as a vacuum and pressure pump.
Free flow: 300 l/min max.
Pressure: 0.7 bar max.
Vacuum: -550 mbar
|
|
Oil free-Linear Diaphragm Pump enviro series
Contamination free blowing
ET series linear diaphragm pumps provide a clean oil free air source, wich is exceptionally quiet in operation and vibration free
|
|
Bellows metering pumps operate on a positive displacement principle. Pumps are designed to displace both corrosive and non corrosive fluids. Accurate and repeatable to 0.5% from stroke to stroke, when pump is set 50% to 100% of full stroke. Dry run capability, self priming, and no dynamic seals. Discharge pressure is maintained over the entire flow range of the pump. Poppet valves are utilized to prevent backflow; and springs are available to provide a positive shutoff, preventing siphoning through the pump in applications where a positive suction head exists.
Typical applications include film and x-ray processors, silver recovery systems, wafer and silicon chip washers and processors, detergent dispensers, blood analyzing equipment, industrial floor scrubbers, thermo therapy equipment, waste removal systems, and wastewater and water treatment systems.
|
|
|
|
|
|
The Micro Pumps are used frequently in the fields of analysis and medicine.
CONCEPT
The Micro Diaphragm Gas Sampling Pumps from KNF
are based on a simple principal - an elastic diaphragm,
fixed on its edge, moves up and down its central point
by means of an eccentric. In this way the medium is
transferred using automatic valves.
The range of KNF Micro Pumps is for the equipped with the patented stress-optimised structured diaphragm, resulting in a high pneumatic performance, a durable product and compact size. New, very efficient
valves and sealing systems as well as the precise placement of the pump head are some of the other technical features we can offer.
For pump drive we provide a selection of dc motors with
various levels of performance, durability and price.
AREAS OF USE
KNF Micro Diaphragm Pumps are used frequently in the
fields of analysis and medicine.
For instance as pumps for gas measurement, for
example for sampling environmental conditions in the
workplace, or for exhaust gas and smoke analysis or
built into machines for measuring blood pressure.
As they are dc driven, the micro diaphragm pumps are
suited for use in portable and stand-alone equipment
|
|
Mini Bellows Pump models are ideal for low flow, low pressure metering applications. The pump is constructed entirely of plastic and utilizes GRI's time-proven bellows technology to provide an accurate chemically-resistant metering pump with a long life, at an economical price.
Tandem Pump configurations are available and the flow rate of each bellows module is independently adjustable to provide a wide range of flow rate settings.
|
|
|
|
|
|
Bleach Compatible Bellows Pump%u2122
GRI is excited to introduce to its current lines of Compact Bellows Metering Pumps and Mini Bellows Pumps, a Bleach Compatible Bellows Pump.%u2122 Engineered to withstand the corrosive and destructive nature of bleach, the Bleach Compatible Bellows Pump,%u2122 as its name suggests, will allow the pumping of bleach utilizing GRI's time-proven bellows and valving technology.
Mini Bellows Metering Pumps are ideal for low flow, low pressure metering applications. The pump is constructed entirely of plastic and provides an accurate chemically resistant metering pump with a long life, at an economical price. Now, because of GRI's bleach compatible technology, the Mini Bellows Metering Pump offers a wider range of use in the medical industry.
GRI's Compact Bellows Metering Pumps were specifically designed for metering applications requiring low discharge pressures. Compact pumps have been successfully applied in photo, X-ray and dental film processors, silver recovery, and scientific and analytical instruments. This pump now offers even more flexibility with its' bleach compatible version.
GRI's goal is to meet your special needs, whether it's modifying a current product or designing a new pump according to your exact specifications. Our technical sales staff and engineering department are uniquely structured to quickly evaluate your application and create a solution specific to your pumping needs.
As the needs of the market change, GRI stands ready with the technology, engineering expertise and manufacturing capability necessary to meet these challenges and provide superior pumping solutions to help move the markets into the future.
|
|
Dry runnig miniature diaphragm pump for liquids
Direct drive with different DC motors
Excellent transfer when handling mixed media liquid / air
Free Flow 180 ml/min
Maximum pressure height up to 80 m H2O
Suction height up to 6 m H2O
|
|
TD05
Contamination free pumping
These micro diaphragm pumps provide a clean oil free vacuum and pressure source which is suitable for continuous or intermittent duty.
|
|
Plastic corrosion-resistant pumps
Pumps for processing chemically-aggressive liquids made from corrosion-resistant thermoplastics: PP, PVC, PVDF, PE-HD. No metal parts in contact with pumped liquid. Chemical pumps designed around system specifications and chemical resistance
Quick maintenance and with easy-to-replace components, diaphragm pumps are fed with non-lubricated air and have an adjustable flow rate and head.
Their explosion-proof properties have been certified for the ATEX version according to Directive 94/9/EC ATEX Equipment.
Speed fine tuning without affecting high pressure. These pneumatic diaphragm pumps also run dry without problems and are equipped with patented internal coaxial exchangers.
|
|
D5 series
Vacuum pump/compressor
Contamination free pumping of air and gas
D5 pumps provide a clean oil-free vacuum and pressure source in a small, very quiet package.
|
|
KNF diaphragm pumps for air and neutral, slightly aggressive, high aggressive or corrosive gases and vapours offer the right choice for many applications. Irrespective of size, the special features of the diaphragm are built into every pump: uncontaminated transfer , no pollution of the media, maintenance-free and gas tightness.
|
|
|
|
|
|
VACUUBRAND's aluminum design diaphragm pump is a perfect match for many applications in the laboratory and operations because it is oil-free and whisper quiet, and because it requires so little service. Diaphragms have especially long lives, and hermetically seal the drive space from the pumping chamber to protect mechanical parts from corrosion. The pumps achieve their distinctively high performance from high pumping chamber volume relative to the minimal dead space. Highly flexible FPM double diaphragms with fabric reinforcement guarantee an extremely long diaphragm lifetime. The pumps operate absolutely oil free and do not have any sliding components on the vapor side; in normal operation they are completely free of abrasion. Besides contributing to the long service intervals, the lack of abrasion also eliminates most of the particulate impurities frequently generated on the vacuum side of scroll or piston pumps.
- innovative connections in the new NT models ensure very low leak rates for excellent flow rates under vacuum and long-term performance stability, even after thousands of hours of service.
- no abrasion, making it dust- and contamination-free
- long diaphragm and valve lifetimes: made of highly flexible FPM, with fabric-reinforced double diaphragms for improved long term stability
- new patented drive support system in NT pump models provide for uniquely quiet, low-vibration operation
|
|
|
The D7 vacuum pump/compressor provides a clean oil free vacuum and pressure source. Suitable for continous duty the D7 it ideal for use in medical and sampling applications where long term reliability is essential.
|
|
Oil free-Linear Diaphragm Pump enviro series
Contamination free blowing
ET series linear diaphragm pumps provide a clean oil free air source, wich is exceptionally quiet in operation and vibration free
|
|
Oscillating Diaphragm Pumps are rated for continuous operation, self-priming, corrosion resistant, and are available in FDA grade materials. In addition, these pumps are compact, economically priced and would make an excellent alternative to Peristaltic Pumps in many applications with the ability to provide up to 4,000 hours life under normal operating conditions.
Typical applications include detergent dispensing, chemical mixing, dish and glass washers, ice machines, analytical instruments, medical and laboratory instruments, and chiller applications.
|
|
For the dosing of liquid chemicals, Alltech Dosieranlagen GmbH has developed the piston diaphragm metering pumps of the FKM series.
These metering pumps meet the highest requirements in operational reliability and accuracy.
Alltech piston diaphragm metering pumps are built in a modular concept. This guarantees high flexibility in combining the pump elements for various areas of applications.
By using different materials and designs for the liquid end, Alltech metering pumps may be used for the dosing of almost all kinds of chemicals.
To find an optimal solution for your dosing tasks, we offer various dosing capacities and pressure ranges.
The integrated pressure relief valve guarantees maximum security.
A wide range of accessories (stroke actuators, pulsation dampers e.g.) completes the range of our production.
|
|
RD5 Series
Rotary diaphragm pump
An eccentrically mounted bearing on the shaft, rotates within a flexible diaphragm. As the shaft rotates, the bearing flexes the diaphragm, squeezing the liquid through the pump.
|
|
|
Pocket bellows models are ideal for low flow, low pressure metering applications. The pump is constructed entirely of plastic and utilizes GRI’s time-proven bellows technology to provide an accurate chemically-resistant metering pump with a long life, at an economical price. Pocket Bellows Pumps are available with fixed crank mechanism only.
|
|
Features
- Transfer and handle your dry process powders quicker, cleaner and at a fraction of the cost associated with installed "systems"
- Replaces Manual Powder Processes
- Reduce Airborne Contamination - With direct transfer from the powder container to your recipe
- Unique Patented Air-Induction System - Avoids the possibility of powder pack-out
- Economical and Simple - Unlike large, complex systems
- Portable - Can be moved from site to site
- Advanced Air-Induction Technology - 4-Way air efficiency valve, delay timer, pump major air valve, air induction valve, main air control valve and air motor muffler
- NPT, BSP and Tri-Clamp material connections
|
|
Features
- Constructed of FDA Accepted Materials
- Electro-Polished 316 Stainless Steel Fluid Section
- Bolted Construction with all Stainless Steel Hardware
- All Investment Cast Wetted Parts
Typical Applications - Food processing, cosmetics, pharmaceutical, chemical additives (food grade), paint, and applications requiring quick-disconnect fluid connections
|
|
ATEX Directive 94/9/EC
As a marketleading producer of air-operated, double-diaphragm pumps worldwide, its is natural for us to comply with the ATEX 100A directive for explosive atmospheres.
Albin Pump AB designs, develops and manufactures pumps, pump parts and peripheral accessories. Albin Pump is consistently striving to meet and exceed the tradition of service, quality and integrity by providing the market with the latest certifications to meet our customers needs. Albin Pump´s employees and its Distributor network are deeply committed to excellence, innovation and customer service.
|
|
Pumps for the printing and paper industry have to meet definite requirements. The pneumatic diaphragm pumps of the ALMATEC F-Series have been developed especially for applications with glues, flexo-print inks, and UV-varnishes.
ALMATEC pneumatic diaphragm pumps of the F-Series are available in two sizes (F 10 and F 20) with max. capacities of 600 resp. 1200 l/h.
The special design includes two separated liquid chambers as well as an integrated pulsation damper, so the pumps provide delivery as well as re-delivery. No second pump is required.
Example flexo-print ink: Ink is transported to the printing machine via the delivery chamber. The second chamber of the pump can be used as an extractor pump. Ink not needed can be sucked from the doctor chamber back to the supply container.
F-Series pumps meet the ATEX requirements of the directive 94/9/EG.
|
|
STANDARD FEATURES
Pumps are ruggedly constructed to withstand the rigors of the pressroom. The inlets and outlets can be configured to meet the requirements of bottom printing corrugated lines or the top decks of the largest CI presses. A variety of corrosion resistant constructed materials permits use with water, alcohol, and solvent-based inks and coatings.
Pump is designed for easy maintenance with a minimal amount of parts.
For situations requiring controlled flow rates from 40 gallons per minute down to a trickle.
Air operation is inherently explosion proof.
Self-priming with the ability to pump liquids containing small solids.
Optional air-powered mixer is available for in-tank agitation.
|
|
ALMATEC pneumatic diaphragm pumps of type AD 6 are a special development for laboratory applications and for sampling water from wells for continuous monitoring of the groundwater under landfills.
They have a maximum delivery volume of 250 l/h which can be infinitely varied by adjusting the air flow. AD 6 pumps are equipped with spring-loaded valves and can therefore be installed in any position.
The housing is made of solid PTFE conductive. This material is resistant to corrosion by virtually all media. Its conductivity permits use of the pump in explosion-hazard areas and for inflammable liquids.
AD 6 pumps meet the ATEX requirements of the directive 94/9/EG.
|
|
|
|
