|
|
Pitot Tube - Series 160/166/167
Insertion Lengths from 6 to 216 Inches, Designed to Meet AMCA and ASHRAE Code
Ellipsoidal Tip Pitot Tube - Series 160E
Insertion Lengths from 0.2 to 1.52 Meters, Designed to Meet British Standard 1042.
"S" Type Stainless Steel Pitot Tube - Series 160S
Insertion Lengths from 18 to 72 Inches, Designed to Meet EPA Spec. 40 CFR (Ch. 1)
Telescoping Stainless Steel Pitot Tube - Model 166T
Adjustable Insertion Length from 11.5 to 36 Inches
|
|
KIMO offers a wide range of high-quality and accurate Pitot tubes, as per the AFNOR NFX 10-112 and ISO 10780 norms.
Pitot tubes Type L
Accuracy : More than 1 %, for a ± 10 ° alignment to the fluid flow.
Pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Body made of stainless steel.
Pitot tubes Type L with TCK
Accuracy : More than 1 %, for a ± 10 ° alignment to the fluid flow.
Pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
Pitot tubes type S with TCK
Accuracy : More than 4 %, for a ± 15 °alignment to the fluid flow.
Pitot tubes with TIG welding and protective tube made of stainless steel. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
The deltaflow pitot is the portable counterpart of the deltaflow DF 25. It is the ideal sampling instrument for performing integrated measurements according to DIN 2640 standards. It possesses the same highly precise profile as the deltaflow DF25 and is used to verify and calibrate existing measurements. The deltaflow pitot is currently in use, for example, in power plants, by measurement teams, and-in the heating and air conditioning industry-to test airflow efficiency, air intake and exhaust, or to test the efficiency of ventilators.
Because the deltaflow pitot can be disassembled, it can be comfortably transported in a carrying case. Its straight construction design allows it to be easily inserted into the sampling cross-section through previously-existing apertures. The sampling profile is extremely impervious to pollution or to the accumulation of condensation. The highly durable stainless steel and the non-sealed design resist temperatures of 1040°C in constant application and can withstand temperatures of up to 1200°C for temporary measurements.
Media: Gasses
Conduit / Channel Diameter: 100..8500mm
Process Requirements: -250..1200 °C / 0..6 bar
ultra-pure through highly polluted, aggressive gasses
Tests / Certifications:
Calibrated at the Department of Flow Technology at the University of Erlangen
|
|
|
|
|
|
• Pitot tubes Type L : pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Body made of stainless steel.
• Pitot tubes Type L with TCK : pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
• Pitot tubes type S with TCK : pitot tubes with TIG welding and protective tube made of stainless steel. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
• Air Flow Measuring blades DEBIMO : simple and cost effective method of providing permanent air flow measurement in rectangular or circular ducts. When used with a KIMO differential pressure device (pressure, transmitter, electronic micromanometer, liquid column manometer, differential pressure switch, ...).
DEBIMO air flow measuring blades ensure accurate indication, control or recording of air flow velocity and volume. Permit velocity measurements from 3 to 100 m/s (9 Pa to 10000 Pa).
Join our distribution network all over the word....Contact us !
|
|
|
Preso’s patented Ellipse Pitot tube DP flow meter offers the highest accuracy and lowest pressure loss of any pitot tube on the market today. Typical performance specifications include +/- 0.75% accuracy, 0.1% repeatability and 17:1 turndown ratio. Typical pressure loss is 3% in a 12” (300 mm) line, with no noise transmission. NIST-traceable calibration also available. The Preso Ellipse is available for liquids, air, gas or steam, in pipe sizes from 2" (50 mm) to 72" (1830 mm) and larger.
|
|
| ... products without technical information |
| |
|
ANVER is the largest manufacturer of Vacuum Tube Lifting systems in the United States with the widest selection of Vacuum Tube Lifters and Replacement Vacuum Tube Lifter Parts in the industry. ANVER VT Vacuum Tube Lifting Systems can be configured to handle all load types: porous, semi-porous and non-porous. For porous and semi-porous load handling, we recommend you allow us the opportunity to test your load in order to determine the actual system capacity and capability. ANVER can provide an ergonomic vacuum tube lifting system for many special and customized lifting applications, a few examples of which are shown on our website.
|
|
The vacuum tube lifter JumboFlex is ideal for the frequent and very rapid movement of lighter goods, i.e. those with a weight of up to 35 kg.
The modular Jumbo system can do almost anything: regardless of whether you want to stack boxes on pallets, load barrels on a truck, move cans, furniture bodies, rolls of film and foil - with the Jumbo, you always have the best solution. All transport operations can be carried out faster, more ergonomically and more safely with the Jumbo.
For anyone who has to lift objects, the Jumbo is an investment in good health, since it relieves the stress on the spine and joints.
|
|
Lifting, lowering, swivelling, loading and transporting loads is "child's play" with the vacuum-tube lifters.
The modular Jumbo system can do almost anything: regardless of whether you want to stack boxes on pallets, load barrels on a truck, stack metal or wooden sheets, move stones or furniture - with the Jumbo, you always have the best solution. All transport operations can be carried out faster, more ergonomically and more safely with the Jumbo.
For anyone who has to lift heavy objects, the Jumbo is an investment in good health, since it relieves the stress on the spine and joints.
|
|
Assembled according to your schedule of conditions, the Mobirail® systems adapt to the configuration of the workstation for an easy handling of the loads (from 75 to 1500 kg) by the operators.
Available in 2 ranges:
- profile hollow rail steel and
- profile hollow rail aluminum.
Combinable with wish according to the degree of expected performances.
Easily integrable pendular systems in any type of building.
Complete program of accessories and adjustable suspensions.
|
|
EM modules for bundles
Electromagnetic modules with capacity up to 8 tons.
They allow to clamp bundles or packs of rounds, sections, sheets and other ferrous loads already strapped.
|
|
| ... products without technical information |
| |
Ranges : 0...1/0...600 bar and vacuum
Industrial service, Liquid filled
For Process Industry
For oil industry, NACE std.
For Food and Sanitary Industries
Laboratory and Test
With Electric contact and micro-switches
|
|
Pressure Gauges
2" and 2.5" diameter
Brass or Stainless Steel construction
Pressure ranges from subatmospheric to 10,000 PSIG
1/4" NPT connections
|
|
|
|
|
|
At any point with limited space, where the process pressure has to be indicated locally, and, at the same time, a signal is wanted to be transmitted to a central controller or remote control room, the model PGT23.063 INTELLiGauge can be used.
Through the combination of a mechanical measuring system and electronic signal processing, the process pressure can be read securely, even if the power supply is lost. The model PGT23.063 INTELLiGauge fulfils all safety-related requirements of the relevant standards and regulations for the on-site display of the operating pressure of pressure vessels. An additional measuring point for the mechanical pressure indication can thus be saved.
The model PGT23.063 is built upon a high-quality, stainless steel pressure gauge in safety pattern version model 23x.30 with nominal size of 63. The pressure gauge is manufactured in accordance with EN 837-1.
The durable, fully-welded Bourdon tube measuring system produces a pointer rotation proportional to the pressure. An electronic angle encoder, proven in safety-critical automotive applications, determines the position of the pointer shaft - it is a non-contact sensor and therefore completely free from wear and friction. From this, the pressure-proportional, 4 ... 20 mA electrical output signal is produced.
The electronic WIKA transmitter, integrated into the highquality mechanical pressure gauge, combines the advantages of electrical signal transmission with the advantages of a local mechanical display.
The measuring span (electrical output signal) is set automatically along with the mechanical display, i.e. the
scale over the full display range corresponds to 4 ... 20 mA.
|
|
Bourdon Tube Pressure Gauges Models RSCh / RSChG / RSK / RSKG
This model is suitable where high safety standards are required, e.g. for oxygen service acc. to EN 837-2.The highly chemical resistant stainless steel case is provided with a solid front between measuring system and dial and a full blow-out safety back, according to S3 of EN 837-1.
Different case sizes are availabel: 63 mm (2½"), 100 mm (4") and 160 mm (6").
Electrical accessories and chemical sealscan be mounted. Numerous options are available to suit the pressure gauge optimized for almost all kinds of industrial applications.
|
|
Pressure Gauges
Utilising its vast experience of providing high quality instrumentation solutions to the worldwide industry, Delta Controls has launched a comprehensive range of instrument gauges.
These guages are produced to the usual high specification and quality that process plant operators, engineering contractors and OEM customers demand and expect from Delta Controls.
By carefully selecting worldwide suppliers that produce to the high quality demanded by Delta, customers can now specify gauges to complement Delta's comprehensive range of pressure process instrumentation.
|
|
MI 150 S/113/1,6
Application:
For all gaseous and low-viscosity liquid media that will not obstruct the pressure system orattack copper alloy parts.
Suitable for industry, heating, water supply,air-conditioning, pneumatics.
|
|
Description & Features:
• StabiliZR™ dampened movement minimizes effects of pulsation and vibration without liquid filling
• Stainless steel case
• Back, bottom, or panel mounted
• 316L stainless steel wetted parts
• CRN registered
• 5 year warranty
Applications:
• Ideally suited for process, chemical and petroleum industry
• Where chemical compatibility and contamination is a concern
|
|
|
|
|
|
The LT120 automatic laser tube cutting system is the ideal solution for exploiting the benefits of laser technology within a contained cost.
Starting from a tube bundle, all the work processes are done automatically within the system: selection of individual bars, measurement, feeding, cutting, conveying and unloading of the finished part.
The LT120 automatic laser tube cutting system is perfect for light metal and thin walled tubes up to 120mm diameter generally used in the most important industrial sectors (furniture production, automotive, assembly plant and heating). The machine can also be efficiently used for simple operations like straight cuts.
Features of LT120 automatic laser tube cutting system:
* low running costs
* proven system reliability
* easy and fast production changeovers
* fully automatic working cycle
* standard CAD-CAM software control packages specifically designed by ADIGE for single and assembled tube programming.
ADIGE also develops customized solutions to meet customer specific requirements.
|
|
|
|
|
|
FL 600 3D
The FL 600 3D system was designed for machining tubes and structural profiles with a maximum external diameter of 610 mm and a maximum length of 24000 mm.
The FL600 3D was conceived to work on tubes with round, square and rectangular sections, which are loaded automatically with a tube loading system from a bundle, while the open section profiles are loaded with a chain loading system. Work range is 90 to 610 mm diameter, for tube lengths to 14000 mm and more. The "heart" of the plant is a tri-dimensional system called "Sphera" which allows any point in a spherical space to be worked: the movement is along 5 interpolated axes, with recirculating ball screws and linear motors. The movements of the workpiece along the work axis are guaranteed by four self-centring mandrels that enable different diameters and sections to be machined, with no change tool change being required.
Variations in workpiece straightness during work are compensated by an integrated floating system, which ensures machining precision even on particularly irregular tubes, preventing dangerous mechanical stresses on the mandrels.
|
|
|
|
|
|
FL 250 3D
Tube Tech Machinery has complemented its range of laser systems with the launch of the new FL 250 3D which allows the tri-dimensional machining of tubes and profiles, with a diameter range of 20 to 254 mm.
The workpiece is placed between the four sliding self-centring jaws of the mobile mandrel. Owing to their design, the jaws do not require claw replacement. The fixed mandrel itself, which consists of a solid structure where four self-centring idling rollers are accommodated, does not require tool-changing. The FL 250 3D loading cell comprises a pick-up system which collects the workpiece from the bundle, while open section profiles are loaded with a chain loading system: three independent manipulators allow the mandrels to be loaded with the tubes from the bundle and the profiles from the chain system.
The "smart" unloading enhances the productivity of our system while substantially reducing downtime caused by the stowing of workpieces. Long workpieces are handled by controlled axes for containing and supporting any tube or profile during machining.
|
|
Speedfly 5
Revolutionary plant for the in-line laser cutting of tubes. It can be used for any profile with diameters of up to 220 mm and more. It overcomes the great drawbacks of the traditional cutting systems still used in today's production of welded tubes.
High cutting quality, absence of burrs and cooling fluids, noiseless operation, and no need for machine downtime for frequent tool changes are the distinctive features of this innovative plant.
|
|
|
|
|
|
TL 312 3D SPEED
The TL 312 3D Speed plant was designed to obtain the best performances in the laser cutting of large-sized sheets with dimensions of 12000 x 3200 mm and more.
The TL 312 Speed 3D is equipped with an automatic pallet change system and with a dual portal where the tri-dimensional cutting head and the laser source are positioned. The first portal, which is very lightweight, carries the cutting head and can therefore move rapidly, performing all the required machinings with high acceleration. The second portal follows the first one like a rubber band, as it is connected to it by pressurised rubber bellows; it carries the laser source enabling all the work area to be reached and its machining tasks to be performed with consistency, precision and rapidity.
The effectiveness of Tube Tech Machinery's solution is proved by the translation speed of 100 m/min that can be reached on axis X, over three times greater than that of traditional laser systems for large-sized sheets, which carry head and source on a single carriage. The use of linear motors ensures excellent dynamic behaviour and high performance.
The system is fully automated and governed by a CNC facility for full independent operation, while the user-friendly CAD-CAM software complements this extraordinary equipment, which is truly unique in the global scene.
|
|
Our TS 4.20 2D system cuts and welds metal sheets by means of a single, special cutting and welding head. The system can process metal sheets with dimensions from 1000 x 2000mm to 2050 x 4100mm and thicknesses from 1 mm to 8 mm, with laser power of 5000W or 6000W. After the process, the metal sheets can measure 4000 x 20000 mm and more. The machine is equipped with an automatic loading system, which allows a high degree of automation and prolonged continuous operation.
Like all TTM machines, the TS 4.20 2d was designed using FEM (Finite Elements Method) structural computation software that enables the dimensional features of the structures to be defined and the strain and deformation states to be optimised in relation to the stresses applied. With this new solution developed to meet customers' specific needs, TTM once again presents itself as a partner-supplier of ideas that translate into innovative, reliable and technologically advanced machines.
|
|
|
|
see the results for the following category : 
