|
|
|
The mvBlueFOX is a compact industrial CCD & CMOS camera solution for any PC with USB ports. A superior image quality makes it suited for most applications. The driver in combination with the FPGA represents a perfect team which reduces the PC load to a minimum during preprocessings like Bayer color conversion. The standard Hi-Speed USB interface guarantees an easy integration without any additional interface board.
|
|
Ultraviolet (UV) option
An increasing number of applications make use of UV light. This makes surface artifacts appear in greater clarity and allows visualization of even smaller features.
The DVL Series cameras are offered with a UV-sensitive option for resolutions of 512, 1024 and 2048 pixels. These cameras incorporate a high-sensitivity imager with fused silica windows for use in the UV down to 200nm.
|
|
sensicam uv
This UV sensitive cooled digital 12bit camera system comprises advanced CCD and elctronics technology. With this on-chip multiplication of the light signal the readout noise of the camera can be neglected ( 50). With its excellent resolution of 1004x1002pixel this high performance cooled digital 12 bit CCD camera system is best suited for extremely low light camera applications. The system features thermo-electrical cooling of the image sensor down to -12°C and an outstanding quantum efficiency in the UV range of the spectrum (QE 15% @254nm and 10% @193nm). Exposure time modes (software selectable) range from 75 µs - 1h. A high speed serial data link connects the system to the PC (fiber optic link available). This low light UV camera system is perfectly suited for scientific imaging (e.g. metrology, semiconductor quality control, nano particle measurements and bio label imaging) applications.
|
|
Visible phenomena are not the only ones of interest for scientific or industrial applications; uv imaging for UV laser beam alignment and diagnostic, semi-conductor mask alignment, lithography, etc are increasingly important. Our cameras sensitive in the UV and low energy X ray region use the latest solid state device technology and offer the following capabilities:
40% quantum efficiency at 200nm can be achieved with new interline chip while offering very good noise characteristics at high frame rates.
High resolution is also available with UV sensitivity with 1.3 million pixels on several CCD chips.
IEEE 1394 (Firewire), RS422, LVDS and camera link frame grabber outputs are used and also analogue video output.
|
|
pco.4000
This high resolution 14bit cooled CCD camera system comprises advanced CCD and electronics technology. With the new approach to integrate the image memory (camRAM) into the camera itself, it enables unmatched fast image recording with 128MB/s. The system features thermo-electrical cooling (delta vs. ambient -45°C), a superior high resolution (4008 x 2672pixel) and low noise (down to 12e- rms). It consists of a compact camera with an external intelligent power supply. The image data are transferred via customer selectable standard data interfaces to a computer (IEEE 1394 (“firewire”), camera link). The available exposure times range from 5µs to 49days. This cooled digital CCD camera system is perfectly suited for low light and high resolution camera applications, like microscopy, aerial photography or quality control.
|
|
pco.1600
This high dynamic 14bit cooled CCD camera system comprises advanced CCD and electronics technology. With the new approach to integrate the image memory (camRAM) into the camera itself, it enables unmatched fast image recording with 160MB/s. The system features thermo-electrical cooling (delta vs. ambient -50°C), a superior high resolution (1600 x 1200pixel) and low noise (down to 12e- rms). It consists of a compact camera with an external intelligent power supply. The image data are transferred via customer selectable standard data interfaces to a computer (IEEE 1394 (“firewire”), camera link). The available exposure times range from 5µs to 49days (500ns opt.). This digital CCD camera system is perfectly suited for low light camera applications like fluorescence imaging and microscopy.
|
|
Digital Wavefront Cameras® deliver fast and reliable evaluation of wavefronts with ultimate performances at any wavelengths. Integrating state of the art Digital Wavefront Sensors®, these cameras measure tilts, divergence and convergence of wavefronts with an outstanding resolution only limited by CCD sensor.
Thanks to its flexibility in dynamic and resolution, Digital Wavefront Cameras® can address the most demanding applications in optics, laser beam analysis or in ophthalmology. Digital Wavefront Cameras® represent the latest advances in wavefront sensing providing unique advantages compared to conventional Shack-Hartmann sensors.
|
|
With immediate effect, the DFW-SX910 will replace the DFW-SX900 model. With his high resolution, range of features, and internal colour treatment, the DFW-SX910 camera is ideal for quality-critical colour imaging applications, in any type of fluctuating lighting conditions.
This new advanced digital camera incorporate an IEEE 1394 digital interface, is easy to install and use, and produce highly detailed, uncompressed images.
|
|
|
|
|
|
The Alta U16M uses a very large format 16-megapixel full frame sensor with microlensing and anti-blooming gates, ideal for applications requiring large field of view, such as sky surveys and radiology.
4096 x 4096 array, 9 x 9 micron pixels
5 MHz 12-bit and 1 MHz 16-bit digitization
32 Mbyte camera memory
USB 2.0 interface: no plug in cards or external controllers
Programmable, intelligent cooling to 40º C below ambient
Binning up to 8 Horizontal x 4095 Vertical
Subarray readout and fast sequencing modes
Precision time delayed integration readout
Programmable fan speed for low / zero vibration
Two serial port outputs for control of peripheral devices
General purpose programmable I/O port
External triggering and strobe controls
ActiveX drivers included with every system (other software sold separately)
Field upgradeable firmware
Self-test capability with data simulators
Fused silica windows
Runs from single 12V supply with input voltage monitor
Compact enclosure
Programmable status indicators
|
|
|
These are cameras with high resolutions suitable for high detail image observation and measurement.
|
|
|
|
|
|
pco.1300 solar
This versatile high performance 12 bit CCD camera system is specifically designed for electro luminescence (EL) applications in the range of 850nm - 1200nm. The pco.1300 oem has an extraordinary quantum efficiency of up to 11 % @ 900nm. At the heart of the camera is an FPGA processor allowing for sophisticated control and accurate timing of the CCD and associated electronics. In addition, a proprietary offset control algorithm has been developed which provides very high offset stability, regardless of ambient temperature or signal changes ensuring accurate and repeatable quantitative data over long periods of time. The pco.1300 solar’s most unique feature is its increased sensitivity in the NIR range of the spectrum. ROI, binning, cooling, as well as other features of the camera can be selected and optimized to accommodate the user's application. Camera features excellent resolution (1392 x 1040 pixel), 12 bit dynamic range, exposure time 5 µs to 1 hour, internal frame buffer for continuous image capture (64 MB min), excellent low noise of 7 e¯ rms @ 10 MHz, selectable regulated cooling to 5 ºC, standard interface IEEE1394a, optimal offset stability and control (< 1 count). This low light camera system is perfectly suited for many sensitive and low noise imaging applications, such as solar cell quality control, NIR fluorescence imaging, EL applications etc..
|
|
|
|
|
|
Lumenera's Lu165 CCD USB 2.0 Camera
Lumenera’s Lu165 series of megapixel cameras are designed to be used in a wide variety of applications,particularly in low-light conditions and where high dynamic range is required. Both color and monochrome, enclosed and board level product models are available.
This ultra high-performance USB 2.0 camera provides 15 fps at 1392x1040 pixels. Based on a high-quality 2/3" CCD sensor with fast global shutter - ideal for capturing objects in motion. 1.4 megapixel ExView HAD CCD provides capture in the lowest of light conditions with, 8 or 12 bit digital output. I/O control for synchronization with strobe and peripheral devices. Advanced camera functions are available through a comprehensive Software Developers Kit, with sample code and full technical support to quickly integrate camera functions into your application.
CAMERA SENSOR
Image Sensor 2/3" format, color or mono, 10.2mm x 8.3mm array
Effective Pixels 1392 x 1040, 6.45µm square pixels
Frame Rate 15 fps at 1392x1040, 30 fps at 640x480 (binned)
Sensitivity High
Dynamic Range 72dB
Exposure Manual
White Balance Auto / Manual
Dimensions (W x H x D) 2.00 x 2.50 x 1.63 inches
Mass ~150g
Power Requirement External 6VDC, 800mA (included)
Power Consumption ~6.0 Watts
Operating Temperature 0° C to +50° C
Operating Humidity 20%-80%, Non-condensing
Interface Connector Standard USB 2.0
Lens Mount C-Mount
Frame Buffer 1 frame buffer (optional expansion to 12 frames)
|
|
Apogee Instruments Inc has been in development of a low cost, high performance follow on to the successful Alta line. This camera fills the current void of lower cost cameras with higher speed and smaller footprints.
Apogee Instruments offers a broad range of professional imaging solutions. Over the years we have built an impressive list of satisfied customers. We are confident that you will find a solution to fit your needs at a cost that won't break your budget.
Contact our Sales Department with any questions you may have about our products or would like to pre-order an Ascent system.
|
|
|
|
|
|
Lumenera's Lu075 High Speed Camera
This high-speed USB 2.0 camera provides 60 fps at 640x480 pixels. Based on a high-quality 1/3" CCD sensor with fast global shutter - ideal for capturing objects in motion. Low light sensitivity provides capture in even low light conditions with 8 or 12 bit digital output. I/O control for synchronization with strobe and peripheral devices. Advanced camera functions are available through a comprehensive Software Developers Kit, with sample code and full technical support to quickly integrate camera functions into your application.
CAMERA SENSOR
Image Sensor 1/3" format, 5.8mm x 4.9mm array
Effective Pixels 640 x 480, 7.4µm square pixels
Frame Rate 60 fps at 640x480, 100+ fps 320x240 (binning)
Sensitivity High
Dynamic Range 60dB
Exposure Auto / Manual
White Balance Auto / Manual
Dimensions (W x H x D) 2.25 x 3.85 x 1.56 inches
Mass ~300g
Power Requirement USB 2.0 bus power, or external 6VDC, 500mA
Power Consumption ~2.5Watts
Operating Temperature 0° C to +50° C
Operating Humidity 0%-95%, Non-condensing
Interface Connector Standard USB 2.0 cable
Lens Mount C-Mount (CS-mount option)
Frame Buffer 1 frame buffer (optional expansion to 50 frames)
|
|
Alta Scientific Imaging Systems
Highest Speed, lowest noise, 16/12 bit dual digitization to >10MHz, TEC cooling to >55C. Lifetime warranty on CCD chamber seal. Fast USB 2.0 and 100Base-T Network Interfaces, advanced I/O control. The Alta imaging systems represent cost effective advanced imaging technology not found anywhere else.
For a full listing of Alta Series models please see:
Alta U Series USB 2.0 Cameras
Alta E Series Network Cameras
Apogee Instruments offers a broad range of professional imaging solutions. Over the years we have built an impressive list of satisfied customers. We are confident that you will find a solution to fit your needs at a cost that won't break your budget.
|
|
|
Hamamatsu has been a pioneer in the world of ultrafast science and technology, i.e. phenomena occurring faster than one billionth of a second. Streak cameras are an indispensable tool in the world of picoseconds and femtosecond phenomena, capturing information that no other instrument can provide. Hamamatsu Systems Division also offers dedicated streak camera systems for specific applications such as the C4780 - Fluorescence Lifetime Measurement System - as well as Picosecond Light Sources and Picosecond Photodetectors.
|
|
|
|
|
|
See incredible resolution with this USB 2.0 camera, providing 3.5 fps at 4008x2672 pixels. Based on a high-quality 43.3mm CCD sensor with global shutter. Unique 10.7 megapixel sensor provides incredible sensitivity with large 9µm pixels and with 12 bit, >65dB dynamic range . I/O control for synchronization with strobe and peripheral devices. Advanced camera functions are available through a comprehensive Software Developers Kit, with sample code and full technical support to quickly integrate camera functions into your application. 3 different lens mount options available: Canon-Mount, F-Mount, K-Mount
CAMERA SENSOR
Image Sensor 43.3 mm (diagonal) format, color or mono, 36.1mm x 24.0mm array
Effective Pixels 4008 x 2672, 9.0ìm square pixels
Frame Rate 3.5 fps at 4008x2672
Sensitivity Excellent
Dynamic Range >65dB
White Balance Auto / Manual
Dimensions (W x H x D) Lw11059 – 3.25 x 2.98 x 5.59 inches
Lw11058 – 3.25 x 2.98 x 5.61 inches
Lw11057 – 3.25 x 2.98 x 5.56 inches
Mass 850g
Power Requirement External 12VDC, 2A (included)
Power Consumption ~18.7 Watts
Operating Temperature 0° C to +50° C
Operating Humidity 5%-95%, Non-condensing
Interface Connector Standard USB 2.0
Lens Mount Canon-Mount, F-Mount, K-Mount
Frame Buffer 1 frame buffer (optional expansion to 6 frames)
|
|
The CoolView VHR is a high resolution CCD camera which has 4000x2672 pixels and interline transfer architecture which allows the CCD to operate without a shutter and at 100% duty cycle. The CCD has a high quantum efficiency of typically 45% @ 550nm.
The camera is deep cooled with DT of 35°C, and uses a Peltier with secondary air cooling. A water cooled version for deeper cooling is also available. The camera has a fast 10MHz readout rate with digitisation to 12 bits and also features a high dynamic range 16-bit mode. The camera features on chip binning and sub area readout.
|
|
dicam pro
This is a high performance intensified CCD camera system with gating times down to 1.5 ns. With its 12 bit dynamic range and a high resolution CCD image sensor it features an excellent signal-to-noise-ratio and the ability of single photon detection. The system is suited for applications in environments with high electromagnetic disturbances. A high speed serial fiber optic data link connects the system to the PC. The camera can be triggered by light or electrical input.
|
|
hsfc pro
Having a single optical input, this camera system comprises a image splitter unit, four intensified CCD camera modules with fast switchable MCP image intensifiers and high resolution CCD image sensors. Each module with its 12 bit dynamic range and a high resolution CCD image sensor features an excellent signal-to-noise-ratio and the ability of single photon detection. Four high speed serial fiber optic data links connect the system to the PC. It can be triggered externally by light or electrical input.
|
|
|
|
|
|
CoolView IDI:
The CoolView IDI features a 1392 x 1040 pixel CCD coupled, by the latest bonding technology, to a specially-developed high resolution image intensifier. Spectral response can be chosen for red, green or blue peak response. A gated version with 5ns gating is also available.
ISIS-4:
The ISIS-4 is an ultra-high gain intensified CCD camera with a double micro-channel plate image intensifier, allowing photon-counting efficiency and ultimate sensitivity. The image intensifier features an extremely low noise photocathode even without cooling, and the optimised electron-optical design produces detection efficiencies in excess of those achieved with standard GaAS (‘third generation’) photocathodes. CCIR or EIA readout.
ISIS-4/1000:
The ISIS-4/1000 is designed for very fast imaging applications and uses camera electronics to provide 1000 frames per second CCD. The double MCP is used to provide sufficient flux, and combined with manual gain control can be used in a variety of light levels from photon counting to fast dynamic imaging at higher light levels. The camera system can be provided with a frame grabber PC and software to provide a complete imaging solution.
ISIS-3:
The ISIS-3 is an intensified camera with the latest image intensifier technology. The use of high resolution MCPs and the technique of using a fibre optic taper to couple the intensifier to the CCD results in excellent image quality.
|
|
sensicam qe
This high performance cooled digital 12 bit CCD camera system comprises advanced CCD and electronics technology. The system features thermo-electrical cooling of the image sensor (down to – 12 °C), extremely low noise (down to 4 e- rms) and an outstanding quantum efficiency, which achieves a high spectral sensitivity in general and especially in the NIR. Exposure time modes (software selectable) range from 500 ns (fast shutter) to 3600 s (long exposure). A high speed serial data link connects the system to the PC (fiber optic link available). This low light camera system is perfectly suited for many sensitive and low noise imaging applications, such as fluorescence imaging, confocal & light microscopy etc..
|
|
pixelfly vga
This high performance digital 12 bit CCD camera system features state of the art in CCD and electronics technology. The system consists of an ultra compact camera head, which either connects to a standard PCI or a compact PCI board via a high speed serial data link. The available exposure times range from 10 µs to 10 s. A digital temperature compensation is integrated instead of a space consuming thermo-electrical cooling unit. All camera functions can be remotely accessed and controlled via digital interface. This compact digital CCD camera system is perfectly suited for many scientific and industrial imaging applications, like microscopy, spectroscopy and quality control.
|
|
|
|
|
|
Lumenera's Mini Lm165 Industrial USB 2.0 Camera
Measuring 44x44x56mm, these compact cameras offer the same performance as our enhanced USB 2.0 camera line, delivering outstanding image quality and value. Features include new locking industrial mini USB and RJ45 GPI/O connector, multiple mounting points, 60 fps at full 640x480 resolution, 100+ fps at 320x240 binning mode, and on-board processing and sensitivity provide outstanding image quality. Both color and monochrome product models are fully supported by the Lumenera Software Developer’s Kit with an application programming interface compatible with C++ and Visual Basic.
CAMERA SENSOR
Image Sensor 2/3” format, color or mono, 9.0mm x 6.7mm array
Effective Pixels 1392 x 1040, 6.45µm square pixels
Frame Rate 15 fps at 1392 x 1040, 30 fps at 640x480 (binned or ROI)
Sensitivity Extremely High
Dynamic Range 66dB
Exposure Manual
White Balance Auto / Manual
Dimensions (W x H x D) 44x44x56mm
Mass TBD
Power Requirement USB bus power or external 5VDC, 500mA
Power Consumption ~2.5 Watts
Operating Temperature 0°C to +50°C
Operating Humidity 5%-95%, Non-condensing
Interface Connector Locking mini USB cable & RJ45 GPI/O connector
Lens Mount Adjustable C-Mount (CS-Mount option)
Frame Buffer 1 frame buffer (optional expansion to 50 frames
|
|
OEM Solutions
When it comes to integrating vision or optical measurement capabilities into one's original equipment, picking separate components on the sole consideration of their state-of-the-art specifications doesn't make it right every time. When it makes it. What is of utmost importance, rather, is the supplier's skills in sorting out the very requirements that govern the final system performance and customizing the right solution for the right cost.
We specializes in supplying industry OEMs with specific solutions that exactly meet their exact vision or optical application requirements.
Here is one example of customization and application-specific solution:
a compact, high sensitivity linescan camera used in genomic instrumentation for the biotechnology industry.
|
|
|
|
|
|
Lumenera's LuX73 OEM Camera
• Slim 2-board camera design
• Identical performance and functionality of full sized cameras
• Tethered cable up to 15cmlength for variablemounting options
• 1, 2, or 3 megapixel sensor options (Lu173C, Lu173M, Lu273C, Lu373C)
• ½" format CMOS sensors
• No lensmount available (intended for integration into OEM enclosure design)
• Mini-USB connector, or locking 4-pin Molex cable for tethered USB and I/O cables
• CCD sensor options can bemade available—call for customization details
As an OEMcustomer you can leverage the success of Lumenera’s line of high-performance USB 2.0 cameras.
Lumenera’s custom cameras can be adapted to fit your application requirements
whether simple or complex. Rely on Lumenera’s expertise for timely modifications, ranging fromsmall hardware and software adjustments such as private labeled enclosures, to complete made-to-spec solutions with alternate form-factors and uniquemechanicals.
As a Lumenera OEM customer, leverage the success of ourwide range of high performance USB 2.0 cameras and expect the following advantages:
• Improve time to market for megapixel cameras
• Reduce development costs/risks
• Differentiate from your competition
• Expertise in integrating peripheral components
Satisfy your application and industry-specific requirements with Lumenera’s “easy to do business with”practices.
|
|
|
|
|
|
The INFINITYX-32 pixel shifting camera has been specifically designed for customers in the clinical, life and material science fields. Available at a fraction of the cost of competitive cameras, this complete imaging solution is an extraordinary tool for professionals who require multi-megapixel resolution, sub-pixel detail, precise color accuracy, high sensitivity, 12-bit data, and low noise levels
Live video provides for real-time focus, while auto exposure and auto white balance add to workflow efficiency and throughput. A USB 2.0 digital interface ensures a simple plug-and-play installation with no need for costly and difficult-to-handle framegrabbers.
The INFINITYX-32 includes INFINITY ANALYZE, an advanced and easy-to-use software tool with a wide variety of functions for image enhancement and analysis, including measurement, annotation, archiving and image processing.
CAMERA SENSOR
Image Sensor 1/1.8" format, 32 megapixel CCD, color or mono, 7.1mm x 5.4mm array
Effective Pixels 1616 x 1216, 4.4µm square pixels
Digital Output 8 and 12-bit uncompressed
Frame Rate 12 fps at 1616X1216, 25fps at 640x480
Dark Current (e-/s) 12
Dynamic Range >66dB
CAMERA CONTROLS
Integration Time 1/1000 to 2 sec.
Global Electronic Shutter
Auto Exposure Automatic / Manual
White Balance Automatic / Manual
Gain Programmable / 1 to 10X optimizable
Lens Mount Adjustable C-Mount lens adapter
Dimensions (L x W x H) 3.85 x 2.00 x 2.75 inches
Mass 300g
Power Requirement USB 2.0 bus power, or external 5VDC – 2.5mA
Power Consumption ~4Watts
Operating Temperature 0° C to +50° C
Operating Humidity 5%-95%, Non-condensing
|
|
It allows quick and precise setting of specimen and microscope, and hence provides comfortable operation.
SPECIFICATION
- Sensor : 3.15 Megapixel Color, CMOS, 1/2"
- Active area : 6.55 × 4.92 mm
- Sensor resolution : 2048 × 1536 Pixel
- Pixel size : 3.2 ¼m × 3.2 ¼m
- 3 × 10 Bit RGB
- Pixel clock : 36 MHz
- Dynamic range : 58 dB (at 10 ms exposure time)
- Max. exposure : 3 s
- Max. frame rate : 35 fps (682 × 512)
- Image resolution : 2048 × 1536
- Binning : 1024 × 768 (2x) und 682 × 512 (3x)
- Digital Interface : IEEE1394a Firewire
- IR-Cut-off filer : fixed in C-Mount
- Optical Interface : C-Mount (0.5× TV Adaptor recommended)
APPLICATIONS
- Life Science
- Pathology
- Histology
- Cytology
- Live Cell Imaging
- Strong Fluorescence
- Documentation / Archiving
- Material Science - Metrology
- Mineralogy
- Manufacture / Semiconductors
- Plastic & Polymers
- Agriculture & Food Science
|
|
The OSCAR family at a glance.
The AVT OSCAR family consists of three very compact IEEE1394 C-mount cameras, which are equipped with sensitive high-resolution, high quality sensors (CCD). Each of these cameras are available in color with IR cut filter. Operating in 12-bit mode (16-bit in High SNR mode), these cameras convince with their outstanding image quality under almost all conditions.
The OSCAR is equipped with an asynchronous trigger as well as true partial scan and integrates numerous smart features which are useful for image processing and microscopy. Three different resolutions of 3, 5 and 8 megapixels leave no wish unfulfilled and offer the right camera for all highly-detailed applications.
|
|
|
|
|
|
STINGRAY – The Transfomer Camera
The STINGRAY falls into the mid-range in terms of price, but offers a breadth of functions unrivaled in its class and an unbeatable price/performance ratio. The six different versions are equipped with a fast FireWire IEEE1394b interface and high-end CCD sensors in color with IR cut filter and monochrome with clear glas filter, with resolutions from VGA up to 2 megapixels. To meet the highest requirements in the industry, the STINGRAY comes optionally in a version with a copper daisy chain connection or 1 x copper combined with 1 x GOF connector (2 x optical fiber on LCLC).
The camera is loaded with typical AVT intelligent functions for image pre-processing, like look-up tables, shading corrections, white blance and 2 to 8x binning for enhanced photosensitivity. Grabber functions, including an internal memory and deferred transport mode, make the STINGRAY ideal for multi-camera operations, while the sequence mode enables lightning-fast parameter changes. The STINGRAY is designed to be modular and flexible, offering a wide selection of lens-mounts, sensors, case variations, interfaces and cable outputs, which can be flexibly configured using buildingblock principles.
|
|
|
|
