|
|
|
Cast Iron and Bronze construction in both self priming and standard configurations. Close coupled, frame mounted and SAE engine drive options available. Flows up to 5,000 GPM and 400 feet TDH. Designed to handle a wide range of water and mild chemical applications.
|
|
The pump and driving motor are assembled as a unit on a common shaft. The transformer oil circulates through the windings thus eliminating any shaft seal and avoiding the danger of oil leakage or entry of air. The complete unit is weatherproof and can be arranged for horizontal or vertical mounting with a variety of branch positions on end suction and side outlet.
The end suction design is selected to meet specific customer duty requirements. All pumps supplied are performance tested and statically tested at 5 Bar in hot oil at 60º C for 24 hours to prove joint integrity.
|
|
SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world. Experience gained from extreme environments such as off-shore oil & gas installations has led to the creation of the SPP Unistream and Eurostream range of end-suction fire pumps, approved for fire protection by the Loss Prevention Certification Board (LPCB), Factory Mutual Approvals
(FM) and Underwriter Laboratories Inc. (UL), all of which are fully compliant to NFPA 20. Other approvals held by SPP include APSAD, CNBOP, ZUS and PSB.
Typical Applications:
Sprinkler systems
Hydrant systems
Deluge systems
Monitor systems
Water curtain
|
|
Goulds Model 5500 is the result of many years of experience designing and building severe duty slurry pumps. It's not only built to stand up to the toughest abrasive slurry services, but also is designed for extreme ease of maintenance and safety. A heavy duty bearing frame and shaft, extra thick wall sections and easily replaceable wear parts add up to many years of service even under the severest operating conditions. Also available as 5500HP.
Specifications:
Capacities to 17000 GPM (3861 m3/h)
Heads to 425 feet (139m)
Temperatures to 250° F (121° C)
Pressures to 500 PSIG (3448 kPa)
Solids to 5 inches (127 mm)
|
|
ELEPUMP DIESEL
The Elepump is also available with a diesel engine, offering better fuel efficiency and lower overall operating cost. Based on customer feedback, the Diesel Elepump offers better overall operating efficiency.
Designed for simple maintenance, Elepump requires only periodic oil checks and changes - and worn parts can be replaced quickly and simply without special tools.
* 45 gallons per minute pumping capacity for large drill site operations that demand greater throughput
* Mounted on 4-cylinder Kubota V1305-40M transmission Offers 30 horse power at 3000 rpm
* Newage 40M 4-speed transmission with integral reduction, providing ratios of approximately 13:1, 9:1, 5:1 and 3:1
* Factory-specified completion kits include a 12V starter and charger, radiator-cooler with HD guard, HD dry-type air cleaner, keystart with glowplug assist, Vernier-type throttle control, a battery rack and cables, Racor fuel filter, electric fuel pump and chain-type coupling
* Battery not included
|
|
The Gorman-Rupp line of engine driven high pressure fire pumps delivers up to 156 PSI and 250 GPM. They are equipped with an exhaust primer. All units have a built-in check valve and include a discharge pressure gauge, brass hose adapters - NPT to National Standard Fire Hose Threads, and a suction strainer.
Specifications
Size: 1-1/2" (37.5 mm), 2-1/2" (62.5 mm)
Max Capacity: 260 GPM (16 lps)
Max Head: 360' (110 m)
Max Solids: 0.3125" (8 mm)
Materials of Construction: Aluminum
Horsepower: 13 HP to 23 HP
|
|
The Fyr Port series portable pumps arespecially designed for applications involving high pressure. Standard features include brass piston type hand primer, recoil starting, and an 8-horsepower two-cycle engine which offers high horsepower in a small package. Two different mounting options are available — skid(20FP-C8SK) or wraparound frame (20FP-C8FR). The complete pumping unit weighs in at a mere 50 pounds — ideal for one-man portability.
* High Pressure performance
* Compact very lightweight design
* High horsepower weight ratio
* One man portability
Optional hose package: Contains 100 feet of 1-1/2" fire hose, adjustable nozzle, tune up kit, and 2-cycle oil in a canvas carrying bag.
|
|
Series TC and TH have been especially developed to sapply internally cooled tools with coolant fluid.
Closed impellers provide optimal hydraulic efficiencies while minimizing power consumption.
Closed impellers
High pressure / no long chips
10 ... 600 l/min
30 ... 520 m
|
|
|
Fristam FM pumps have been specially developed for generating high pressures and for operation with extreme pressure loads. The pressure is increased by several successive pumping stages.
|
|
Goulds HT 3196 is specifically designed for superior performance for high temperature applications in the chemical industry.
Specifications:
Capacities to 4500 GPM (1023 m3/hr)
Heads to 925 feet (282 m)
Temperatures to 700° F (372° C)
Pressures to 450 PSIG (3102 kPa)
|
|
HOT WATER 100 - 160 °C UNCOOLED
ZLN - Standard hot water pump
Up to temperatures of 160 °C - EN 733/ DIN 24255, can be used with an uncooled, balanced mechanical seal.
ZLI - Inline hot water pump
Up to temperatures of 150 °C and is of an economical inline design
HOT WATER 160 - 230 °C UNCOOLED
ZEN / ZDN - hot water pumps
The ZEN, a volute casing to EN 22858, & the mechanical seal has been placed at the “cold end“/drive end, of the pump and can operate up to 230 °C.
HEAT TRANSFER OIL 100 - 350 °C UNCOOLED
ZTK and ZTI - Compact design thermal oil pumps
Specially developed for installation in compact machinery. The series only differ from each other in the shape of the pump casing.
ZTN -Thermal oil pump
For handling thermal oil up to 350 °C in the heating
prosesses.
ZTK - magnetic drive
Up to 300 °C uncooled
ZTK - magnetic drive
With a heat barrier up to 400 °C – uncooled
|
|
|
|
|
|
MDM is a wide ranging line of chemical process pumps designed to solve the most demanding chemical handling applications. Two materials of construction and convenient mounting configurations allow MDM to handle many aggressive chemical and high purity applications.
Unexpected dry running won’t damage the pump or interrupt the process. Our new design allows the pump to handle these situations with ease. High purity process fluid will not be contaminated by trace metals due to our combination of high purity materials and meticulous construction.
High strength rare earth magnets are totally encapsulated within fluororesin moldings. Small, lightweight and perfectly concentric magnet capsules optimize pump efficiency. An expanded temperature range (up to 300°F) as well as increased solids handling capabilities (up to 10%) provides users with solutions for their difficult applications.
Installation and maintenance time are reduced with our compact, close-coupled design. Operating costs are reduced thanks to simple, modular construction and individually replaceable parts.
|
|
JP-840: Horizontal centrifugal pumps in Polypropylene and PVDF
These centrifugal pumps made of Polypropylene or PVDF are operated by a direct-drive motor (max 3000 rpm) for fast fluid transfer with flow rates ranging from 6 to 75 m3/hour. Their special open-impeller design allows pumping even with very dirty liquids having apparent viscosity up to 500 cps (at 20°C) and small suspended solids. There are two versions available with different internal mechanical seal depending on use: lip seal and mechanical seal.
The products of this manufacturer have a very good cost/ performance ratio. The pumps have standed the test of time since many years in nearly all industries worldwide.
|
|
The Lutz centrifugal pumps of the range TMB/AM/TMR are horizontal, dry running, single stage plastic centrifugal pumps with magnetic drive for the delivery of clean, corrosive and little solid containing liquids.
The typical industry sectors are the chemical engineering, the galvanic and surface treatment, the sewage and water treatment industry, the semiconductor industry as well as the general industry.
Since the pump is magnetically driven, no mechanical seals are required and therefore the hydraulic system is hermetically sealed from the environment.
Absolutely safe for dry running:
The model TMR execution „R“ is suitable for dry running by means of a patented magnetic „two axial directions self-alignment system“.
- Sealless and environmentally safe
- Bearings made of Carbon, Ceramic, SiC or Rulon®
- Operating safety and high efficiency
- Robust and powerful
- Long working life
- Easy maintenance
|
|
ALW horizontal type centrifugal clear water pump is used to transport clear water and other liquid has chemical and physical property similar with the clear water. It is applicable to water supply and drainage for industry and city pressure increasing water supply for high building ,garden irrigation, pressure increasing for fire fighting, long distance transportation, heating and cooling circulation, cold and warm water circulation pressure increasing and matching equipment, the using temperature is T ≤ 80 ℃.
- Stable function
- watertight
- low noise
- Low rate of failure
- convenient repair
- small occupying of the land
|
|
CB and CBI series of pumps are horizontal,multistage centrifugal pumps, with the impellers mounted on the motor shaft. The pump housing is attached to a base plate. The design makes the pump suitable for installation in small spaces. A high quality mechanical seal is included as a part of the pump.
CB: The discharge and suction chamber are made of cast iron. All other pump parts in contact with the liquid are made of stainless steel.
CBI:All parts of pump in contact with the liquid are made of stainless steel.
Operating Limits
50Hz
- Capacity : max. 14m3/h
- Head : max. 78m
- Liquid temperature : 0ﾟC to+90ﾟC
60Hz
- Capacity max.16 m3/h
- Head : max. 78m
- Liquid temperature : 0ﾟC to+90ﾟC
Applications
- Domestic use
- Liquid transfer and circulation of liquids within light industry and farming
- Pressure boosting
- Heating and cooling systems
- Specialized OEM equipment
|
|
HBI and HBN series are light-duty stainless steel horizontal multistage centrifugal pumps for use with base mounted electric motors. The mechanical seal is designed for simplified replacement.
These pumps are suitable for pumping slightly corrosive liquids because product contact parts are 304 or 316 stainless steel.
Operating Limits
50Hz
- Capacity : max. 14m3/h
- Head: max. 58m
- Liquid temperature : 0ﾟC to+110ﾟC
60Hz
- Capacity max.16 m3/h
- Head : max. 78m
- Liquid temperature : 0ﾟC to+110ﾟC
Applications
- Air-conditioning system
- Cooling system
- Industrial cleaning
- Water treatment(Water purification)
- Fertilizing/metering system
- Environmental application
- Other special applications
|
|
|
These heavy-duty and rugged horizontal centrifugal pumps are designed, engineered and constructed to handle corrosive, abrasive and other aggressive fluids, as well as those liquids which must remain free of metallic contamination. CHEM-GARD® pumps are available in a wide selection of thermoplastics and in ANSI/DIN, self-priming, close-coupled and integral pump/shaft motor designs.
|
|
Series 4 pumps can deliver a maximum flow of 14 GPM (50 LPM), and are capable of serving applications with a maximum head of 21.5 ft. (4.7 m) (49 ft. [15.6 m] when
driven by an air motor). Applications include electronic medical equipment, etching machines, photo processing equipment, hospital thermal blankets and food heating cabinets.
Standard construction is of polypropylene, with options for wetted materials that include Ryton® or Kynar®. Ceramic, Buna N rubber, and Viton® for total chemical
compatibility. Carbon bushings are available.
|
|
Hygienic Pumps
The Hovap series of hygienic pumps has been designed for continuous operation on thin liquids with viscosities of up to 500m Pa.s. such as milk, wine, cream and beer etc. For complete versatility this range can include heating jackets, frequency controllers, flushed seal and is available with unions, plane ends or flanges.
* Favourable NPSH
* EHEDG approved
* Capacity from 55m³/h to 250m³/h
|
|
Construction
- Close-coupled self-priming centrifugal pumps with built-in strainer.
- B-NMP: bronze version.
Applications
- For water circulation in swimming pool filtration systems.
- For clean or slightly dirty water with solids in suspension.
|
|
Suitable for applications where the flow required varies continuously or the pump operates against a closed discharge valve.
MODEL :- CWHA
Capacity:- 90 m3/h - 400 USgpm
Delivery head max:- 1900 m - 6300ft
Max speed:- 6800 rpm
Casing pressure:- 160 bar - 2320 psig
Lubrication :- oil
MODEL :- CWHG
Capacity:- 80m3/h - 350 USgpm
Delivery head max:- 780m / 2575ft
Max speed:- 4300 rpm
Casing pressure:- 85 bar - 1230 psig
Lubrication :- grease
FEATURES
- Wide operating range up and down the performance curve
- Complies with API 8th edition
- Complies with ATEX
- Pulsation free operation
- Seal only on suction side
- No contact between pumped medium and pump lubricant
- Ability to handle solids and gases
- Dry running capability
BENEFITS
- Handles wide variations in flow (from 20% to 110% of
BEP flow)
- Wide application in oil extraction and oil processing
- Suitable for Category 2
- Extended MTBF
|
|
UTS SERIES
TECHNICAL SPECIFICATIONS
Materials AISI 316L
Flow rate 320 mc/h
Head 140 m
Temperature range -80 °C - 320 °C
Allowable pressure rating Da PN 10 a PN 40
Viscosity 400 cSt
Impeller type Closed
Motors 0.75 - 75 Kw
ATEX 1-2G
Velocity range 1450 - 3500
Pass solids Max concentration 5 % in weight
Hardness 800 Vk, Size max. 200 µm
Standard DIN 24256 (EN22858)
Inlet outlet port ISO 2858
|
|
The model ICM is a metallic magnetic drive chemical process pump made of stainless steel, hastelloy, ductile cast iron, and special metals. Designed for normal and demanding chemical process applications.
Specifications:
Capacities to 340 m3/h (1490 USgpm) at 2900 rpm & 400 m3/h (1760 USgpm) at 3500 rpm
Heads to 160 m (525 feet) at 2900 rpm & 210 m (685 feet) at 3500 rpm
Temperature Range -40° C to 180° C (-40° F to 360° F), optional as ICMP up to 280° C (530° F)
Pressures to 16 Bar (235 PSIG), optionally 25 bar (360 psi); sizes 65-40-315 and 80-50-315: 25 bar (360 psi) standard
Materials - Ductile Iron, 316 Stainless Steel, Duplex SS, Alloy 20, Hastelloy, Titanium
|
|
|
The 3298 is designed specifically to handle moderate to severe corrosives with or without solids. As a sealless design, it's an effective alternative to pumps with mechanical seal problems. Meets strictest EPA regulations.
|
|
CQ TYPE magnetic force driving pump (called magnetic pump), is the new product, which use the permanent magnet join-axis working principle for centrifugal pump, and has advantage of reasonable structure, advanced workmanship, full sealed, non-leakage and cauterization-proof, its performance can be match to the same product of foreign countries.
- reasonable structure
- advanced workmanship
- full sealed, non-leakage
- strong corrosion-resistance
- compact conformation、good- looking appearance
- small in size 、low noise
- uniformity of operation
- convenient maintenance
|
|
Liquiflo's ENDURA® AB-Series is our Patented Air-Barrier Centrifugal Pump. This innovative revolutionary design was the recipient of the 1995 Vaaler Award. The ENDURA® AB can run dry indefinitely and handles solids - something no other pump in the industry can do.
The AB (air-barrier) combines the best features of a standard sealed pump with that of a mag-drive pump, while eliminating the drawbacks commonly associated with these designs. This patented design makes the ENDURA® AB unlike any other pump in the industry.
|
|
|
|
|
|
Process magnetic drive pumps MDM series
Unique design endurable to dry running (Non contact system)
The pump design features a mechanism to withstand dry running. High magnet power of the rare earth magnets prevents the magnet capsule coming into contact with the thrust ring of the rear casing, thus preventing melting of fluororesin components due to heat generation. This greatly improves resistance against dry running in comparison with conventional magnetic drive pumps made of fluororesin. Note: Only CF type (fitted with high density carbon bearing) can cope with dry running. Dry running is not permitted in the case of KK type.
ETFE and PFA available in standard models
Carbon fibre reinforced ETFE (CFRETFE) and PFA linings can be supplied to meet many varying duties. PFA being a natural unfilled material generates fewer contaminants and makes it ideally suited for transfer of high purity chemicals.
Back pullout system
In order to facilitate inspection and maintenance, this series employs the back pullout system. This enables one to conduct inspections internally and replace parts without removing piping. The pump is designed to include safety measures that can prevent the liquid from leaking when the foot support is pulled back.
|
|
|
FTI's DB Series Magnetic Drive Pumps are the product of advanced engineering CFD design software and superior magnetic flux technology. Using powerful neodymium magnetic technology, the DB sealless mag drive pumps are an ideal replacement for mechanical sealed pumps in corrosive duty applications.
|
|
Using the latest, patented pump technology, Hayward's Series R all-plastic, corrosion resistant pumps will stand up to the most aggressive, demanding industrial and commercial applications year in and year out. From the heavy duty, thick wall, glass reinforced polypropylene or ETFE pump body construction, to the rugged epoxy painted motors, there is simply no better mag drive plastic pump available anywhere. And Hayward backs every one of its Webster mag drive pumps with an extended two year warranty.
With horsepower ratings from 1/3 to 5 HP, applications requiring flow rates from 5 to 140 GPM and with maximum total dynamic head discharges up to 141 feet, you will find a Webster Magnetic Drive Pump to meet your requirements. And because the process media never contacts metal, there is never a danger of pump failure due to rust or corrosion. Because they are magnetically driven, they have no seals, thus no emissions, leaks or expensive seal replacements.
|
|
|
|
