|
|
Flow rate: 80 Litres/min (21.1 USgallons/min)
Pressure up to 1.2 bar (17.4psi)
Features:
• Heavy duty robust design
• Stainless steel construction
• Long life DC motor
• Silent running
• Anti-clog impeller design
• Long life mechanical seal
• Single tool servicing
• ISO 8846 MARINE and USCG Regulations for Ignition Protection
• ISO 8849 MARINE Bilge Pump Standard
|
|
|
|
|
|
The features are as followed:
The frame plates for type EHM pumps have replaceable wear-resistant metal liners . The impellers are made of wear-resistant metal. The frame plate liner and impeller for EHM pump are adoptable of hard metal only.
Bearing assembly use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication.
The shaft seal could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications.
Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices.
Wide performance, good NPSH and high efficiency. The pump of this type may be installed in multistage series to meet the delivery for long distance.
Application:
The type of EHM pumps are using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc.
For example: Coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station.
Notation:
EHM-6E
E:Excellence
H:High concentration
M:Metal lined
6: Discharge size (inch)
E: Frame type with maximum power
|
|
|
|
|
|
Heavy duty process horizontal pumps, between bearings with a axially split casing and double suction impeller.
Pump components geometry optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis lead to an high product reliability.
Double suction, closed impeller, with a solid hub, to maintain axial balance, under different operating conditions.
Rotor operates away it's critical speeds.
Near centerline casing mounting for high temperature stability.
Deep stuffing boxes integrally cast with pump casing, in accordance to API 682 std suitable to accept any type of mechanical or packing seals.
Axial split bearing housing for easy inspection and maintenance procedure.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Fully designed according to latest edition of API 610 std.
Suction and discharge nozzles, integrally cast with casing, are arranged on side-side position.
'CARB' or hydrodynamic line bearing for high temperature application.
Three bearings arrangements available:
Ball Radial / Ball Thrust
Sleeve Radial / Ball Thrust
Sleeve Radial / Tilting Pads Thrust (Kingsbury Type).
|
|
The ToP-Flo® name represents the finest in sanitary process equipment. ToP-Flo® pumps have been designed to offer efficient transfer of product over a wide range of head and viscosity conditions. ToP-Flo® pumps are easy to install, clean, and operate.
ToP-Flo® pumps are suitable for use in CIP (clean in place) installations. This feature enables easy self-cleaning with no dismantling or take-down. Sanitizing of all product contact areas is automatic.
All ToP-Flo® pumps are available in standard inlet sizes and outlet sizes. In addition, enlarged inlet sizes are available for special applications.
|
|
Designed for heavy-duty, high-efficiency applications. Provides exceptional corrosion resistance. Impeller and shaft are one piece, which connects directly to motor shaft; eliminating such problems as vibration, short bearing life, high NPSH requirements, high seal maintenance, poor tolerance, and adverse operating conditions.
- 316L stainless steel volute, backplate, impeller and shaft
- Five-bladed impeller with deeper eye for improved inlet
characteristics
- Modular seal design - one size fits all models
- Wide range of seal options, including standard
commercial seals
-Stronge JM-type motor with large bearings and strong
shaft
- Base mounting options available with all sizes
- Temperature range of fluids up to 450° F.
|
|
Materials
Wetted parts AISI 316 Bearings SiC Bracket WCB Special alloy: Hastelloy, Incoloy, Titanium
Technical Data : Flow Rates up to 400m3/h Total delivery heads up to 1300 m Temperature Rating from -150° up to +450°C Flange Rating PN 100
Construction
Horizontal multistage centrifugal pump Permanent Magnet drive system Separation of liquid chamber/atmosphere by means of an isolation shell Synchronous drive transmitted by inner magnet and outer magnet system Sintered Silicon Carbide Bearings Barrel execution Bearing Frame construction
Applications
Pumping acids, hydrocarbon, diathermic oils, liquid gases, dangerous fluids, explosive, toxic.
Further material available if request
Various materials from the standard special Constructions
|
|
Materials
Wetted parts AISI 316 Bearings SiC / Special Carbon Bracket WCB Special alloy: Hastelloy, Incoloy, Titanium
Technical Data : Flow Rates up to a 45m3/h Total delivery heads up to 35m Temperature Ratings up to 200°C Pressure rating up to PN 16
Construction
Horizontal Centrifugal Pump for general applications Permanent Magnet Drive system Separation of liquid chamber/atmosphere by means of an isolation shell Synchronous drive transmitted by inner magnet and outer magnet system Sintered Silicon Carbide Bearings / Special Carbon Bearing Frame and Close coupled execution
Applications
Pumping acids, hydrocarbon, diathermic oils, liquid gases, dangerous fluids, explosive, toxic.
Further material available if request
Various materials from the standard special Constructions
|
|
Verdermag mag drive pumps
The Verdermag series of pumps comprises the metallic Global models complimented by the non-metallic V-MD, GPMD, GLMD, TB and U Series, as well as the Global mag drive metallic series. The Verdermag range is therefore a complete, well-balanced series of magnetically coupled centrifugal pumps.
As with all series of Verdermag centrifugal pumps, current emphasis is on maximum interchangeability and quality improvements, hence all our products are covered by a two-year guarantee. Our motto is "simple by design."
Advantages Verdermag
• Zero leakage
• No mechanical seals or packed glands
• No external flushing systems
• Ensure a clean and safe operating environment
• Close coupled design
• No alignment required
• Increased Mean Time Between Maintenance
|
|
The Verdermag pump series TB & U mag drives are developed as a result of thorough research. With thrust balancing (TB) and universal purpose pumps (U). The patented Thrust Balancing Design eliminates axial thrust bearings and provides the basis for a controlled internal environment. This design minimizes the issue of secundary containment by providing secondary bearings.
Features and benefits Verdermag drive pumps
Flows up to 300 m3/h, Head up to 110 m
Suitable for volatile liquids using non-metallic mag drive technology
Thrust balanced impeller
No axial bearing problem, no cavitation or entrained air in the fluid
Standard SiC replaceable wear parts
Particles cannot enter containment shell of inner magnet gap.
NPSHr is equal to standard sealed pumps
Best Efficiency Points are equal to standard sealed pumps
Simple maintenance
Wear rings work as secondary bearing to protect impeller/inner magnet assembly
Very good price-quality combination
|
|
Materials
Part in contact with liquid PP / PVDF Shaft / Bearings Al2O3 / PTFEC Bracket WCB
Technical Data : Flow Rates up to a 150m3/h Total delivery heads up to 58m Temperature Ratings up to 90°C Pressure rating up to PN 6
Construction
Horizontal plastic Centrifugal Pump for general application Permanent Magnet Drive system Separation of liquid chamber/atmosphere by means of an isolation shell Synchronous drive transmitted by inner magnet and outer magnet system Alumina ultra pure 99,7% shaft, PTFEC Brgs Close Coupled execution
Applications
Pumping acids, hydrocarbon, liquid gases, dangerous fluids, explosive, toxic.
Further material available if request
Various materials from the standard special Constructions
|
|
Materials
Wetted parts AISI 316 Bearings SiC Bracket WCB Special alloy: Hastelloy, Incoloy, Titanium
Technical Data : Flow Rates up to 1000m3/h Total Delivery Heads Up to 220m Temperature from -150° to a 450°C Pressure Rating Up to PN 100
Construction
Horizontal Centrifugal Pump Permanent Magnet Drive system Separation of liquid chamber/atmosphere by means of an isolation shell Synchronous drive transmitted by inner magnet and outer magnet system Sintered Silicon Carbide Bearings Bearing Frame and Close coupled execution
Applications
Pumping acids, hydrocarbon, diathermic oils, liquid gases, dangerous fluids, explosive, toxic.
Further material available if request
Various materials from the standard special Constructions
|
|
Materials
Part in contact with liquid PP / PVDF Shaft / Bearings Al2O3 / PTFEC Bracket WCB
Technical Data : Flow Rates up to a 45m3/h Total delivery heads up to 35m Temperature Ratings up to 90°C Pressure rating up to PN 6
Construction
Horizontal plastic Centrifugal Pump for general application Permanent Magnet Drive system Separation of liquid chamber/atmosphere by means of an isolation shell Synchronous drive transmitted by inner magnet and outer magnet system Alumina ultra pure 99,7% shaft, PTFEC Brgs Close Coupled execution
Applications
Pumping acids, hydrocarbon, liquid gases, dangerous fluids, explosive, toxic.
Further material available if request
Various materials from the standard special Constructions
|
|
Materials
Wetted parts AISI 316 Bearings SiC / Special Carbon Bracket WCB Special alloy: Hastelloy, Incoloy, Titanium
Technical Data : Flow Rates up to a 10m3/h Total delivery heads up to 110m Temperature Ratings up to 200°C Pressure rating up to PN 25
Construction
Horizontal Peripheral Pump for general applications Permanent Magnet Drive system Separation of liquid chamber/atmosphere by means of an isolation shell Synchronous drive transmitted by inner magnet and outer magnet system Self-balancing impeller Sintered Silicon Carbide Bearings / Special Carbon Two executions: Close coupled standard,Close coupled for high temperature ( up to 350°C)
Applications
Pumping acids, hydrocarbon, diathermic oils, liquid gases, dangerous fluids, explosive, toxic.
Further material available if request
Various materials from the standard special Constructions
|
|
Materials
Part in contact with liquid PP / PVDF Shaft / Bearings Al2O3 / PTFE Bracket WCB
Pumping acids, hydrocarbon, liquid gases, dangerous fluids, explosive, toxic.
Technical Data : Flow Rates up to a 15m3/h Total delivery heads up to 70m Temperature Ratings up to 90°C Pressure rating up to PN 10
Construction
Horizontal plastic peripheral Pump for general application Permanent Magnet Drive system Separation of liquid chamber/atmosphere by means of an isolation shell Synchronous drive transmitted by inner magnet and outer magnet system Alumina ultra pure 99,7% shaft, PTFEC Brgs Close Coupled execution
Applications
Further material available if request
Various materials from the standard special Constructions
|
|
Designed for re-circulating service in reverse osmosis and other membrane systems, the 200MS Series multistage pumps offer lower start-up and run costs due to the high efficiency, two impeller design. These pumps produce a smooth, constant flow rate that reduces RO membrane fouling. They include many of the features of the 200 Series pumps, including strong investment cast impellers, low NPSH requirements and tighter running clearances.
- Rated up to 1250 psi maximum pump casing pressure
when pumps are placed in series
- Maximum differential pressure 250 psi (based on water)
- Sanitary 3A construction for food and dairy processing;
wet ends 316L stainless steel
- Low NPSHR investment cast impeller features 5 bladed,
open design for easy CIP and gentle product handling
- Heavy duty cast iron bearing frame keeps shaft rigid and
concentric for long seal and bearing life
-Balanced, water flush, double shaft seal standard
|
|
|
|
|
|
MULTI V/NEXIS V
Overpressure
BEACHES Of USE
Flows until: 140 m3/h
Heights mano. until: 240 m
APPLICATIONS
- In the processes of the trades of water and them
derived applications:
- skid of membrane filtration
- unit of disinfection by U.V.
- adduction, overpressure, transfer...
- washing high pressure
- protection fire
- swimming pool
- In agriculture:
- watering, irrigation
Pumped fluids
- Standard Range: nonaggressive clear liquids (drinking water, glycolée water...)
- Range 316L: aggressive liquids (sea water, demineralized water, chlorinated water...)
ADVANTAGES
- Hydraulic Whole out of stainless steel
- Optimized Reliability: outputs raised thanks to the profile of the wheels, limiting the number of stages, the size of the trees and thrusts
- Easy Installation: openings In line
- Process of disassembling/particularly easy reassembly
- Range 304: nonaggressive clear liquids (clear liquids and neutrals)
- Range 316L: aggressive liquids (sea water, demineralized water, chlorinated water...)
- Mechanical seal cartridge out of standard following model
|
|
|
|
|
|
For liquids up to 50 mm²/s (cSt), which can contain air, be abrasive, corrosive and compatible with cast iron, bronze or stainless steel. Can be located above or on side of the liquid. Some pumps sizes can self-prime up to the physical limit of 8-9 m. As:
Animal meat, Bentonite, Clean or dirty solvents, Cooling milk, Diesel, Fertilizer, Fire fighting water, Flood drainage, Gasoline, Light-oil, Lime milk, Liquid manure, Petrolium products, Rain water, River water, Soda, Sump water, Transformator oil, Wash fluids, Wastewater, Water with cutting sand,
Water with mud, Water with sand, Water with solids and many more....
Used by transfer, load and unload, neutralizing, by-pass, spray, circulating, dewatering, irrigation, priming, well-point duty
In industry, water treatment, refineries, ship building, environmental projects, construction, agricultural, civil guards
closed-coupled, Bi-Block, bare shaft, wit el.motor, or engine, on base plate or trailer
24 Sizes wie many Versions adapted to the different use
from 5 m³/h to 1200 m³/h
from 0,1 Bar to 6 Bar
|
|
|
IMS models are dependable, economical replacements for suction pumps commonly supplied as original equipment on foreign manufactured machine tools. They should not be used to circulate fluids containing fine contaminants. For applications requiring the circulation of liquids containing large amounts of foreign matter, Graymills IMV Series centrifugal pumps are recommended.
|
|
NEXH
Industry: Process
BEACHES Of USE
Flows until 400m3/h total Heads until 150mCE
APPLICATIONS
A broad choice of materials makes it possible to meet specific needs in industry.
ADVANTAGES
- High efficiencies hydraulics and vibratory
- Many options
- High strength to the fluids aggressifs
|
|
The WEMCO Self-Primer is a rugged & dependable self-priming, solids handling, trash pump. A solids handling pump that is suitable for a wide range of applications. True solids handling pumps for tough jobs.
Features / Benefits
- Stainless steel 17-4 PH shaft.
- Cast steel impeller.
- Ductile iron casing and bearing.
- Ductile iron cover plate and fill port cover.
- No tools required for impeller adjustment.
- Shimless impeller clearance adjustment.
- Passes stated solids.
- BuzzSaw Self-Cleaning Wear Plate
- Higher actual efficiency.
- Solid silicone carbide seal faces.
- More rugged and dependable.
- Better value.
- Lower life cyle cost.
- Market leading 66 month warranty.
- Enhanced safety features.
- Higher operating pressure.
- Directly interchangeable - pumps and parts
|
|
|
TN Series pumps are designed to cover a wide range of pumping applications. They can handle thin and heavy liquids containing abrasives and bits of solids, while maintaining consistent and dependable flow. Except for 24" and 36" models, pumps are designed so that there are no bearings or seals in the liquid, making them virtually maintenance-free.
|
|
Floway Pumps' Vertical Hydrocarbon Pumps are built around the versatility of the vertical pump design for the API industry. Our extensive line of low NPSHR impellers allows us to meet demanding NPSHA requirements.
Features / Benefits
- Compliant with API 610 current edition
- Multi-staging in the medium specific speed range
- High pressures with premium efficiences and low operating costs
- Low NPSH first stage construction with Nss below 11,000
- Pressure and flow variations are achieved by changing number of stages or impeller type
- Pump bowl assembly is characterized as low energy per stage resulting in a broad flow range with excellenct hydraulic stability
- Thrust balanced impellers are available for pump axial thrust reduction and assist in obtaining the desired thrust bearing rating/life
- Thrust pot assembly is available in applications where non-thrust carrying motors are required
|
|
|
|
|
|
The VI line heavy duty process pumps, are vertical single stage type
with a side discharge column
These pumps are specifically used on sump applications.
Pump components geometry optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis lead to an high product reliability.
Closed type impeller with front and rear wear rings as well as balancing holes, to minimise the axial thrust.
Large eye single suction 1st. stage impeller to meet low NPSH requirements.
Deep stuffing boxes, designed in accordance to API 682 Std., suitable to accept any type of mechanical or packing seal.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Fully designed according to latest edition of API 610 Std.
Pump shaft fully machined to respect the more restrictive run-out API limits.
As a standard, the rotor axial thrust is supported by a duplex oil lubricated ball angular contact type bearings.
Discharge column, line shaft and support column may consist of multiple sections, depending upon the pump setting. Discharge column mounted with a sliding fit through the sole plate to account for thermal expansions.
Renewable intermediate bushings, lubricated by the same pumped fluid or from an external source, are provided in correspondence of all column sections.
|
|
|
|
|
|
Created by the same engineers and manufactured side-by-side with the dependable WEMCO and WEMCO-Hidrostal pumps your already have in service, the WEMCO Model CF Chop-Flow pump is just as rugged and dependable. It is a cost-effective addition to the problem-solving, trouble-free WEMCO pumps you installed years ago. The WEMCO Model CF Chop-Flow pump chops as it pumps, keeping oversized solids and stringy material from clogging your downstream process.
Features / Benefits
- Designed from scratch as a WEMCO Pump, the Chop-Flow pump brings the chopper pumps' segment the same kind of user-friendly pumps you've trusted from WEMCO for over 60 years - rugged, reliable, dependable, and maintenance free.
- High hydraulic effeciency.
- Wrap around nose vanes insure effective chopping at the center of the impeller, without the need for an impeller nut.
- Rear pump out vanes with cutting slots repel and chop any material that gets behind the impeller.
- The wearing parts - the cutting bar and rear cutting teeth - are easily and inexpensively replaceable.
- All clearances are easily adjustable externally, without the need for 2 people and the hassle to unbolt and move the pump and/or motor as required by other designs.
- Top quality materials and castings throughout - no flimsy fabricated parts to corrode.
- Although the pump is completely new technology, it is dimensionally interchangeable with your present pump. Simply remove the old technology, and the Chop-Flow will bolt up to your existing piping and coupling.
- Available with packing and all conventional mechanical seals.
|
|
The new Polylok pumps are now available in 1/4'', 1/3'', 4/10'' and 1/2'' HP sizes, including both effluent and sewage ejector models. These new pumps are designed to deliver the dependable service and long life expected from any product bearing the Polylok name. They include features required for residential and light commercial applications, as well as several new features (including an all ball bearing construction, and an integrated clip to hold the float switch) not normally found in pumps of this size.
FEATURES:
- Non-Toxic Oil
- All ball bearing construction
- Stainless steel fasteners and motor shaft
- Integrated clip to hold the float switch cable
- 2'' NPT vertical discharge
- Vortex impellers
|
|
Seal-Less Brushless Water Circulating Pumps...
offer basic pump/motor designs from 12 GPM to 26 GPM in either 12 VDC or 24 VDC motor designs. Variable speed is available for the 12 GPM pump. The seal-less pump design is magnetically coupled which provides for a leak-proof pump. There are no rotating wet seals to wear out and leak. Detailed pump information is provided on the individual product sheets. AMETEK seal-less pumps are not designed for, and should not be used in, life sustaining applications.
|
|
|
|
|
|
Standardized centrifugal pumps NOS/NOLH, INTO 733 - ISO 5199
BEACHES Of USE
Flow: up to 1800 m3/h
HMT: up to 140 mCE
Operating pressure max: 10/16 bar following hydraulics
Beach of temperature: -40 to 170 °C
DN32 with 300
Viscosity max: 150 cST
APPLICATIONS
Effluents: Slightly charged clear fluids and, fluid corrodents, acids, solvents...
Transfer of fluids for the following applications:
- Industrial Applications
- Water supply industrial
- Industrial Water supply
- Périprocess (circuits coolant, buckles heating...)
- Systems of filtration
- Systems of cleaning, washing in industry
- Protection fire (Sprinklers) for certain models
ADVANTAGES
- Hydraulic High efficiencies
- Simple Maintenance, interchangeability with all pumps in conformity with the standard IN 733 (NFE 44111)
- Tree and stages reinforced in accordance with standard ISO 5199
- For the drinkable water supply, a certified version ACS is available on request
In option: Spacer, wheel bronze, hydraulic stainless, version ATEX
|
|
NFCH
Centrifugal pump standardized INTO 733 for coolants and thermal oils
BEACHES Of USE
Flows: up to 1000 m3/h
HMT: up to 95 mCE
From 0 with 120°C: pressure max 16 bar
From 120 with 300°C: pressure max 13 bar
From 300 with 350°C: pressure max 10 bar
DNN 32 to 200 mm
Viscosity max: 150 cST
Hydraulic material: Cast iron GGG40.3
APPLICATIONS
- Chemical industry: circuits of heating, engines, process of polymerization, transfer of viscous products, plastics and synthetic fiber factories...
- Industry of the plastic and rubber: circuits of heating, machines of moulding, automatic injection, production of adhesive tape...
- Food industry: furnaces of faisandage, distillation of fatty-acids and glycerin...
- Industry of paper and laundries: corrugated cardboards, washing, drying machines and of the desiccators...
ADVANTAGES
Fund of body with weak heat transfer
Car-cooled mechanical seal
Standard construction in accordance with the standard IN 733
|
|
NESH (IN 733)
NESD-NESE (IN 22858)
Centrifugal pumps monocellulaires normalisees car-cooled for overheated water
BEACHES Of USE
Flows: up to 600 m3/h
HMT: up to 90 m EC
NESH: PN16, T°max 180°C, DN32 to 150 mm
NESD: PN25, T°max 207°C, DN32 to 125 mm
NESE: PN40, T°max 230°C, DN32 to 125 mm
Hydraulic material: Cast iron GGG40.3
APPLICATIONS
Water circulation and transfer pump overheated in the following scopes of application:
- Energy production
- Climatic Genius
- Industry general, plastic, painting, textile, paper, etc
- Possible Version ATEX
ADVANTAGES
- Supports with double fitment female conforms to the DTU 65.3 for pumps NESD/NESE
- Car-cooled Pump not requiring an additional cooling system of the trimming or bottom of body
- Easy Maintenance thanks to the system "process" allowing the disassembling of the mobile without unslinging the pump housing (option spacer)
|
|
|
|
|
|
Pumps autoamorçantes with side channel:
- EX: version stainless 316L
- EZ: version Cast iron
Pump EX:
Fluids: lights and/or corrodents like the acids, solvents or foams, fluids dyphasic...
Débit : up to 22 m3/h
Height mano. : jusqu'à 180 mCE
Beach of temperature: -60 to 250 °C
Operating pressure max: 10 and 16 bars
DNN: 12 to 50 mm
Viscosity max: 300 cST
Pump EZ:
Fluids: lights, hydrocarbons, solvents, viscous fluids until 300cST...
Débit : up to 20 m3/h
Height mano. : jusqu'à 120 mCE
Beach of temperature: -30 to 180 °C
Operating pressure max: 10 and 16 bars
DNN: 12 to 50 mm
Viscosity max: 300 cST
APPLICATIONS
Important suction head, difficulty or risk of draining
Discharge, taking away and transfer of chemical fluids in fields of chemistry, petrochemistry, pharmacy, the nuclear power...
Mobile or fixed groups of discharge for various products, food of loops of distribution, equipment of machines with automatic cycle with reversible operation, injection of reagents for water treatment...
ADVANTAGES
- Aspiration up to 8,5 mCE.
- Low number of revolutions
(1450 rpm EX-EZ 12,20,32,40,50)
- Strong total head
(2900 rpm EX-EZ 12,19)
- Compactness
- Reversible
- Interchangeable standardized Engine
- In option, magnetic coupler on pump EX
|
|
|
|
