|
|
Modular high-performance CNC-turn-mill-centers
The UniCen is a turning and milling center with integrated B-axis where all requirements for complete machining have already been implemented: turning, milling, drilling and thread-cutting all on one machine. The workpiece is loaded on one machine only and can then be finished completely. With up to five interpolating axes even complex free form faces can be machined.
|
|
|
|
|
|
The Unicom 6000 machining centre is ideally suited for vertical turning and multi-sided machining of complex components. This highly flexible and powerful machining centre for complete machining results from the continuous development of vertical machining centres over a period of more than 25 years.
The concept of Unicom 6000 is based on a moving table with integrated carousel turning station and an interface that can receive pallets of up to 2.500 mm in diameter. The table movement is designated as Y-axis and it runs underneath a traverse with cross slide and spindle carrier. The movements of cross slide and spindle carrier are designated as X-and Z-axis respectively.
Unicom 6000:
4-Axes complete machining centre with HSK100-A interface, carousel turning station and pallet changer. The machine can be equipped with a right angular head or a universal head, in combination with C-axis mode in the carousel turning station.
Unicom 6000-HV:
5-Axes complete machining centre with carousel turning station, pallet changer and HSK 63-A interface in the integrated Unisign Nutator NC machining head as 5th axis, in combination with C-axis mode in the carousel turning station. This configuration is capable of 5-axes machining of complex components.
|
|
Highly productive milling-turning centers with one (MT) or two (MT-TWIN) milling spindles and one or two turning spindle(s) for complete machining of semi-finished products and saw sections.
Maximum workpiece quality by complete machining on one machining center. Workpiece clamping is done by means of clamping chuck or device.
The MT-S is designed for highest flexibility and ideal for small batches. The MT and MT-TWIN series offer maximum productivity for medium and large batches.
Reduction of costs per part by up to 30 % thanks to TWIN technology and 5-axes complete machining.
|
|
|
|
|
|
The Leonard machines are a complete and modular range of Horizontal Lathes for the machining on medium to large work pieces with highest performances in terms of rigidity for rough operations and precision for finishing operations. The main feature of these machines is the technology of the preloaded Hydrostatic ways which are successfully used for both cross and longitudinal slides.
Other machining operations can be performed with the Leonard system, like Boring, Milling or Drilling operations. The different working units can be Combined on a column with rotating base ("B" Axis) or on different Pallets to be manually or automatically installed in the carriage.
The Leonard lathe can be supplied with different type of Steady rests according to the work piece and the required machining.On demand different accessories are available like the work piece probe, the tool probe and the Automatic tool changer.
Safop has developed some special system for the measuring of high sophisticated work pieces like the turbine rotors. The Run Out Measurement System and Blade Measurement System are used with success by the main producers of this type of work pieces.
|
|
Drilling
Machining with coolant supply through the tool, regardless if the tool is in radial, axial or in an inclined position. Accuracy-killing changes between various machines is avoided.
Thanks to very high feed forces and high power also at low speed drills with large diameter can be used with optimum performance. A single look into the speed-power-diagram or the speed-torque-diagram shows the difference...
|
|
| ... products without technical information |
| |
Renishaw probe systems provide an innovative solution to improve the efficiency of your machine tools.
Tool setting can measure the size of tools before cutting starts, and to check for tool damage or breakage during the machining operation.
|
|
| ... products without technical information |
| |
HMC Chucks feature the "Perma Fix" Roll Lock System, with its long fine slots of the internal bore, is an integral part of the entire body. This design assures ultra accuracy and rigidity. When tightening the nut, the needle roller bearings rise on the exterior taper of the chuck body and clamp evenly around the entire 360° tool perimeter. As a result, the greater the clamping pressure, the higher the concentricity.
Superior steel alloy allows tough hardening treatment for greater durability. The New Hi-Power Milling Chuck can be operated thousands of times before even the slightest wear will become apparent. The patented pin mechanism assures positive non-slip locking for large diameter 2" shank cutters under the heaviest cutting conditions.
|
|
|
|
|
|
Increased productivity
need not mean heavy investments in new machines.
3Refix is remarkably simple way to lay a solid foundation from which to view the future with confidence – tool up without indication and cut your production costs!
3Refix technology is based on a modular hole pattern with 100x100 mm pitch and 20 mm diameter reference holes. The reference tables have clearly-marked reference holes – A1, A2, B1, B2 etc – and every accessory has two 20 mm diameter holes, which pick up the references from the table. The R0-hole gives the X/Y-position and the R1-hole gives the angle relative to the axes of the machine. This makes it possible to set up the workpiece without the need for alignment and gauging afterwards. So 3Refix accessories provide an unmistakable and fixed position with known references.
The accessories in the 3Refix range usually have a reference height of 30 mm, among other things to allow machining straight through the workpiece. The design also allows a flush pot to be pushed in under the workpiece during EDM machining.
The full effect of 3Refix technology is attained by consistent application with general systemization and standardization of all machine tables and accessories. System 3R can supply reference tables for practically all types and sizes of machines – reference tables that give a distinct interface between machine table and auxiliary tool.
|
|
|
|
see the results for the following category : 
