|
|
MODEL SERIES - DC33
PMDC GEARED MOTOR
Design - Motor DC33 is a carbon brush DC motor which is used in combination
with many Mech Tex gearheads. The standard gearheads used in conjunction with this motor are GB2, GB5P, GB5H, GB38OCP, GB3, GB4, GB7, GB8 & GBW. Depending on the application, output speed, load applied, etc. the type of gearhead can
be selected. Various types of gears i.e. poly acetal, sintered iron, brass or steel gears can be used based on the requirement. Poly acetal or sintered
gears damp the noise. Case hardened steel gears are always on the output
for load considerations. Complete poly acetal gears are used when the output
torque required is low. Linear drive is possible with gearhead GB4,GB7,GBW
with M6 x 1 mm pitch screw. The linear guide & screw arrangement can be
done only on special request.
|
|
MODEL SERIES - DC30
PMDC GEARED MOTOR
Design - Motor DC30 is a carbon brush DC motor which is used in combination with many MechTex gearheads. The standard gearheads used in conjunction with this motor are GB2,GB5P, GB5H, GB38OCP, GB3, GB4, GB7,GB8 & GBW. Depending on the application, output speed, load applied, etc. the type of gearhead can be selected. Various types of gears i.e. poly acetal, sintered iron, brass or
steel gears can be used based on the requirement. Poly acetal or sintered gears damp the noise. Case hardened steel gears are always on the output for load considerations. Complete poly acetal gears are used when the output torque
required is low. Linear drive is possible with gearhead GB4, GB7, GBW with M6 x 1 mm pitch screw. The linear guide & screw arrangement can be done only on special request.
|
|
MODEL SERIES - DC28
PMDC GEARED MOTOR
Design - Motor DC28 is a carbon brush DC motor which is used in combination with many Mech Tex gearheads. The standard gearheads used in combination with this motor are GB2, GB5P, GB5H, GB38OCP, GB3, GB4, GB7, GB8 & GBW. Depending on the application, output speed, load applied, etc. the type of gearhead
can be selected. Various types of gears i.e. poly acetal, sintered iron, brass or steel gears can be used based on the requirement. Poly acetal or sintered gears damp the noise. Case hardened steel gears are always on the output for load considerations. Complete poly acetal gears are used when the output
torque required is low in an economical model (GB7P). Linear drive is possible with gearhead GB4, GB7, GBW with M6 x 1 mm pitch screw. The linear guide & screw arrangement can be done on special request.
|
|
Miniature DC Coreless motor
Miniature DC Brushless motor
* Coreless Motor Characteristics
-Diameter Ø 4 to 18
-Voltage 3 to 12 V
Spur or Planetary gear box and Feedback device are available.
* Brushless Motor Characteristics
-Diameter Ø 1.5 to 30
- Voltage 3 to 24 v
Spur or Planetary gear box , feedback device are availabe.
Application :
* Optical and Measuring instruments
* Medical instruments and apparatus
* Factory Automation and instrumentation
* Servo system for Remote control
|
|
Small Coreless motor
Small Brushless motor
* Coreless motor
- Outer diameter : Ø7 to 18
=Voltage 3 to 12v
- Output power : 0.19 to 3.5 W
- No load speed : 9,000 to 17,500 rpm
- Starting torque : 0.43 to 3.5 mNm
Spur or Planetary gearbox and feedback device are available.
* Brushless motor
- Outer diameter Ø 1.5 to 30
- Voltage 3 to 24 v
Spur or Planetary gearbox and feedback device are available
* Applicatition
- Optical and Measuring instruments
- Medical instruments and apparatus
- Factory Automation and instrumentation
- Servo system for remote control
|
|
Johnson Motor Permanent DC (PMDC) flat motors below Ø 15 mm
Dimension: Ø 6 x 9, flat 5, shaft Ø 0.8 mm
Supply: nominal 1.8 VDC
Torque:
@ stall 0.17 mNm
@ max. efficiency 0.045 mNm
@ max. power 0.087 mNm
@ constant 0.307 mNm/A
Speed:
@ no load 42400 rpm
@ max. efficiency 31350 rpm
@ max. power 21170 rpm
Max. current:
@ no load 0.072 A
@ stall 0.566 A
@ max. efficiency 0.2 A
@ max. power 0.319 A
|
|
Ultra flat dimensions
No cogging or preferred rotor position
No iron losses
Extremely low current consumption
Low starting voltage
Low rotor inertia for extremely fast acceleration and braking
Extremely light and compact
Custom systems available from design to production
Very cost effective
Precision gearboxes available in all sizes
|
|
Johnson Motor Permanent DC (PMDC) flat motors Ø 15.0 ~ 19.9 mm
Dimensions: Ø 15.5 x 18.6, flat 12, shaft Ø 1.505 mm
Supply nominal: 5 VDC
Torque:
@ stall 1.871 mNm
@ max. efficiency 0.381 mNm
@ max. power 0.649 mNm
@ constant 3.267 mNm/A
Speed:
@ no load 10500 rpm
@ max. efficiency 8363 rpm
@ max. power 5250 rpm
Max. current:
@ no load 0.04 A
@ stall 0.613 A
@ max. efficiency 0.157 A
@ max. power 0.326 A
|
|
Key Attributes and Characteristics:
- Frame sizes from 8mm (0.31 in.) to 35mm (1.38 in.)
- Speeds up to 12,000rpm
- Torque range of 0.64 mNM (0.09 oz. in.) to 115 mNm (16.3 oz. in.)
- Low power consumption ratings
- Ironless rotor
- Central stator magnet
- Compact bearings
- Precious metal commutation system
- Copper-graphite commutation
Advantages
- High acceleration
- High efficiency
- Low losses and low electromagnetic interference
Portescap Brush DC motors can be customized with options such as gearboxes, connectors and cables, custom coil designs and more.
|
|
Single-phase capacitor motors Series KD.1 and three-phase motors Series DR.1
The motors are solidly designed and are maintenancefree for life.The multi-grooved stator contains a threefold winding which, together with the phase-shifting capacitor, creates a symmetrical rotating field at the rated working point of the motor.The rotor is of the squirrel-cage type. Two- or four-pole motors with a variety of design Iengths and diameters provide rated torques from 0.75 to 12.6 Ncm. Can be combined with reduction gear units, brakes, and tachogenerator systems.
|
|
|
The DC-motors can be combined with control electronics, gearboxes, brakes and encoders in a modular system to provide a flexible, adaptable, market-oriented solution.
|
|
Appliance Motors
Applications
Semiautomatic washing machines of unique speed, automatic washing machines top load and automatic washing machines front load.
Characteristics Standard
Single-phase motors
Unique speed (4 poles) or double (2/12, 2/16, or 2/18 poles)
Permanent Capacitor
Thermal protector
Level of protection IP00
Isolation class "B"
Tension 110V or 220V
Frequencies: 50 or 60Hz
Rests with bearings or bushings according to application
Optional Main
Axis with pulleys
Fixation by spear
Fixation by the legs
|
|
Since more than 25 years Giem is a leader in the field of induction motors characterized by high electromagnetic efficiency. Available in a rich variety of versions, they represent the most reliable solution for different applications in the thermal ventilation field.
Induction motor Ø 58
Long duration version available (ball-bearing)
Double speed version available
Thermal protection based on the motor impedance or by means of a thermostat or a fuse
Voltage: 12 -110 - 240 VAC
H class available
VDE and UL approvals on request
|
|
Main features of Iskra AC Induction motors:
* High efficiency.
* High specific power.
* Small size.
* Low noise operation.
* Long life without maintenance.
* Precise control.
|
|
Type
0RK1A-AW2J
Series
Reversible motors (1 W)
Technical data
Type
0RK1A-AW2J
Frame size [mm]
42
Output power [W]
1
Shaft type
round
Gear ratios [1:x]
no gear
Rated speed for 50 Hz/60Hz [r/min]
1000/1200
Max. permissible torque for 50 Hz/60 Hz [Nm]
0.01/0.008
Protection class
IP20
Power supply
single-phase 100 VAC
RoHS-compliant
yes
|
|
|
Brush DC motors are mechanically commutated motors that are good for high speed applications where responsiveness and small package size is needed. Brush DC motors are easy to drive and cost effective when long life is not required.
|
|
4-Pole Electrical Designs for High Current Capability
Ball Bearing Construction for Heavier Load and Long Life Capability
High Efficiency Permanent Magnet Designs
Rugged Welded Clip for Magnet Retention, Not Glued
Castings Designed for Maximum Heat Dissipation
1/4 HP - 4HP, up to 5000 RPM, 12-72 VDC
|
|
Single-stage AC Motor, Used in Hand Dryer
Model Number:ND-B
Key Specifications/Special Features:
* Application: vacuum cleaners, hand dryer
* Stage: single
* Voltage: 100 to 240V (50 to 60Hz)
* Input power: 200W to 1,800W
* Insulation class: A, E, B and F
* Maximum vacuum: 26kPa
* Maximum airflow: 3.5m3/minute
* Maximum efficiency: 36%
* Dimensions: 130mm
* Height: 114, 116 and 118mm
* Outer packing: 12 pieces/carton
* Loading volume:
800 carton/9,600 pieces per 20-foot
1,534 carton/18,408 pieces per 40-foot container
|
|
DC Electric micro -motor
*DC Brushless motor
Diameter Ø 1.5 mm to 22mm
Voltage : 3 to 24 v
Driver is available.
Spur gearbox or Planetry gearbox and feedback device are available
-Applicaion
Endscope
catheter
Medical robot
Micro actuator
|
|
|
Canon Precision's brushless motors are compact in size and provide high output power. Two types are offered; an outer rotor type with high rotational stability and an inner rotor type with quick response. Inner rotor types can be equipped with reduction gears and encoders. Various custom options can be incorporated to fit your applications.
|
|
Canon's 26mm Gear Head Motor
Rated Voltage: 12V
Gear Ratios: 1/20-1/410
Rated Load: 58mNm – 294mNm
Rated Speed: 15 r/min – 245 r/min
Rated Current: 170mA – 342mA
Starting Torque: .25Nm- 3.23Nm
Canon will gladly attempt modifications to achieve the exact speed, power and current required of your application.
|
|
No cogging or preferred rotor position
No iron losses
Extremely low current consumption
Extremely light and compact
Smooth and accurate speed, position, and torque control
Electronic commutation for extremely long operational lifetime
High precision gearboxes available in all sizes
Control electronics available for all motor series
Available as linear actuator
Custom systems available from design to production
|
|
No cogging or preferred rotor position
No iron losses
Extremely low current consumption
Low audible and electrical noise
Extremely light and compact
Smooth and accurate speed, position, and torque control
Low vibration
Speeds up to 100,000 rpm
Electronic commutation for extremely long operational lifetime
High precision gearboxes available in all sizes
Feedback components available in all sizes
Control electronics available for all motor series
Custom systems available from design to production
|
|
No cogging or preferred rotor position
No hysteresis or eddy current losses
Extremely low current consumption
Ultra flat dimensions
Extremely light and compact
Smooth and accurate speed control
Speeds up to 60,000 rpm
High power rare earth magnets
Electronic commutation for extremely long operational lifetime
High precision gearboxes available
Control electronics available for all motor series
Custom systems available from design to production
Autoclavable and vacuum rated motors available
|
|
• Fast speed up to 50,000 rpm and up to 30W of continuous output power
• Ultra compact. At 32 mm (1.26”) diameter by 11.7 mm (0.46”) length, the nuvoDisc is over 75% shorter and over 90% lighter than typical competitor motors.
• With a weight of only 26g, applications benefit from being lightweight.
• High efficiency. Reduces power supply requirements by drawing less current,
resulting in less generated heat.
• Low vibration. High speed slotless design provides characteristic smooth operation.
*A slotted design is also available on request when detent torque is needed, for applications such as Damper Control.
|
|
|
Brushless DC motors provide high power density and long life for applications requiring speed control. NMB’s BLDC motors are available in 0.1W up to 1kW.
|
|
|
These motors are a marvel of modern engineering! They combine rare earth magnets with a coreless design to produce high torque motor with diameters ranging from 4mm to 36mm. They feature a sintered bronze bearing to support the output shaft. Originally designed for vibration functions in mobile phones, these come without the weight and are finding increasing applications in models, miniature toys, medical instruments and many miniaturised consumer applications.
|
|
FHA-C mini Series Servo Actuators, combining precision Harmonic Drive gearing with AC servo motors, offer unique features unsurpassed by conventionally geared drives. Used in highly demanding industrial servo systems they provide precision motion control and high torque capacity in a very compact package.
Sine-commutated AC servo motors provide smooth torque without the brush wear or commutation limit associates with DC servo actuators. Encoder, mounted directly onto the motor shaft, provide position feedback information. The backlash-free Harmonic Drive gear is provided with grease lubrication specially developed to ensure minimum maintenance requirements and long service life.
The fully digital SC-610 Series Controllers are available for the control of these Servo Actuators. A menu driven setup software running under MS-Windows allows a comfortable parameter optimisation and system diagnosis.
|
|
|
Nanomotion's EDGE motor is the smallest industrial motor of its kind available in the marketplace today. Providing unlimited linear or rotary motion, the EDGE motor offers extensive opportunities in applications that suit a wide range of industries. The EDGE motor works with a uniquely designed, compact ASIC-based driver, and can be operated with any servo controller. The EDGE motor can be easily integrated into most bearing structures, and is ideal for mass production opportunities.
|
|
DC Electric Micro Gearmotor
* Gear Coreless motor
Diameter : Ø7 to 18 mm
Voltage 3 v to 12v
Gear type: Spur gear :Planeteary gear
Several gear ratio are available
* Gear Brushless motor
Diameter Ø1.5 to 30 mm
Voltage 3 to 24 v
Gear type : Spur gear , Planetary gear
Several gear ratio are available
|
|
|
|
